Dewalt DW745 Support Question
Dewalt DW745 Support Question
Find answers below for this question about Dewalt DW745.Need a Dewalt DW745 manual? We have 1 online manual for this item!
Question posted by inksew on August 5th, 2013
Loose Miter Guide
Just bought a dw745. I find it mostly impressive as to quality, ease of use and ripping lumber. However the miter gauge does not fit well in the track. There is a lot of slop or play. There is a definite 1/32" difference. There is probably no fix or remedy except using a different miter gauge. Is dewalt miter gauge #391921-00 a good alternative and a better fit?
Current Answers
Related Dewalt DW745 Manual Pages
Instruction Manual - Page 3
...;nitions: Safety Guidelines
The definitions below may result in minor or moderate injury. WARNING: Indicates a potentially hazardous situation which , if not avoided, will not fit the outlet, have a ...a potentially hazardous situation which permits you and the tool's electrical system. THIS MACHINE MUST BE GROUNDED WHILE IN USE.
Use only three-wire extension cords that have three-prong...
Instruction Manual - Page 4
...safer at all through sawing. • DO NOT PERFORM RIPPING, CROSSCUTTING OR ANY OTHER OPERATION FREEHAND. • NEVER reach...use the next heavier gauge. No loose clothing, gloves, neckties, rings, bracelets, or other conditions that accept the tool's plug. Keep blades sharp and clean for Table Saws
WARNING: ALWAYS USE SAFETY GLASSES. The use depending on another tool. Don't leave tool...
Instruction Manual - Page 5
... piece or cut and violently thrusts the work piece with loose knots, flaws, nails or other foreign objects. The splitter can result.
• CLEAN THE TABLE/WORK AREA BEFORE LEAVING THE MACHINE. For less than 2" (51 mm) wide, you must use of a miter gauge or rip fence or any cut that completely severs the work...
Instruction Manual - Page 6
...lumber (...Use of harmful chemicals. Miter gauge C. ON/OFF switch L. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Specifications
15 AMP Miter Angle Bevel Angle Blade Size Max. Miter gauge 5.
Examine all loose items from power sanding, sawing, grinding, drilling, and other construction activities. Rip... the risk of injury, do this tool can generate and/or disburse dust, ...
Instruction Manual - Page 7
...PLATE 1. Rip fence (NOTE: Adjust rip scale before attempting to Rip Scale Adjustment.)
2. Blade guard
3. Blade height adjustment crank
Tools needed for...Miter gauge (if required for assembly include a Phillips screwdriver and the wrenches included with
your table saw . Raise the saw . Rip Fence
The rip... on the plate and pull it clockwise.
Use the arbor wrench (supplied) to snap both...
Instruction Manual - Page 8
... the guard and splitter for proper alignment and clearance with the DW745 mounts to the right of serious personal injury, have push stick ready to use , the blade guard can be in place
at the top of...the back of the arbor nut wrench into the saw as shown in the mechanism.
5. NOTE: For ease of the throat plate should be flush or slightly below
the surface of the table top and secured ...
Instruction Manual - Page 9
... of the saw table. A hole (KK) is in use with this tool does not operate, check the power supply.
Refer to fit beneath the footprint of a FIG. 14 padlock with the nameplate... To reduce the risk of the rip fence if the user switches between thick and thin kerf blades. TO ATTACH THE MITER GAUGE
FIG. 13
The DW745 includes a miter gauge for proper performance of serious personal ...
Instruction Manual - Page 10
... locator screw and adjust the position of the blade to the miter slot first. Check rip scale adjustment. Use a Phillips screwdriver to Miter Slot)
WARNING: Cut Hazard. English
NOTE: Your saw is ...PP) holding the lock lever in the locked position. NOTE: The rip scale only reads correctly when the fence is still loose, tighten the
spring further. Tighten the locator screw and repeat on the...
Instruction Manual - Page 11
... miter gauge. Use extra care when the guard assembly cannot be kept sharp. Allowing them to fit on the side of
9 WARNING: Before connecting the table saw , always inspect the guard and splitter for the use the fence to reduce the risk of 5,000 RPM or
greater.
4. WARNING: Ripping or crosscutting may cause saw to the...
Instruction Manual - Page 12
... enters the blade to prevent contact with the desired cut location. Remove the rip fence and place the miter gauge in Figure 25.
4. While using a block as a cut-off , allow the blade to stop on
the...at the same height as a guide or length stop , and carefully slide the work piece an inch or so in a thrown work piece and possibly injury.
1.
Use the push stick(s) to
hold ...
Instruction Manual - Page 13
...gear may not lift
the guard properly.
Three Year Limited Warranty
DEWALT will maintain the tool and replace worn parts caused by feeding the work piece into a liquid. This ...the work piece
shapes, such as crosscutting except the miter gauge is locked at the rear of injury, only DEWALT recommended accessories should be used with the wing screws. Repairs
To assure product ...
Instruction Manual - Page 44
...., 701 Joppa Road, Baltimore, MD 21286 (JAN07) Form No. 650150-00 DW745 Copyright © 2006, 2007 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; the array of pyramids on the surface of lozenge-shaped humps on the handgrip...
Similar Questions
Dcr015 Will Not Turn On When Plugged In
Just bought it clearance and when I plug it in it doesn't turn on. Red light blinks once and nothing...
Just bought it clearance and when I plug it in it doesn't turn on. Red light blinks once and nothing...
(Posted by Ijdelafuente92 7 years ago)
Led Light Stopped Working
I have just bought a dw717xps I plugged it in to the power supply and switched it on the light lit u...
I have just bought a dw717xps I plugged it in to the power supply and switched it on the light lit u...
(Posted by Garycrewe 9 years ago)
Dw745
Will the Freud SBOX8 box joint cutter set work with the DW745 table saw?
Will the Freud SBOX8 box joint cutter set work with the DW745 table saw?
(Posted by Dennisbertuccelli 9 years ago)
Changing Chuck
just bought a secondhand d25404k drill. chuck very rusty, how do i change it.. thx
just bought a secondhand d25404k drill. chuck very rusty, how do i change it.. thx
(Posted by denimpatch 10 years ago)