Dewalt DW745 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DW745 manuals!
Problems with Dewalt DW745?
Ask a Question
Free Dewalt DW745 manuals!
Problems with Dewalt DW745?
Ask a Question
Most Recent Dewalt DW745 Questions
Dw745
Will the Freud SBOX8 box joint cutter set work with the DW745 table saw?
Will the Freud SBOX8 box joint cutter set work with the DW745 table saw?
(Posted by Dennisbertuccelli 9 years ago)
Having Problems With The Anti-kickback Sticking On The Throat Plate When Raisin
and lowering the saw blade.
and lowering the saw blade.
(Posted by sjsbsmitty 9 years ago)
Loose Miter Guide
Just bought a dw745. I find it mostly impressive as to quality, ease of use and ripping lumber. Howe...
Just bought a dw745. I find it mostly impressive as to quality, ease of use and ripping lumber. Howe...
(Posted by inksew 10 years ago)
Dewalt DW745 Videos
DEWALT DW745?MICRO JIG GRR-Ripper?No2
Duration: 1:13
Total Views: 2,809
Duration: 1:13
Total Views: 2,809
DeWalt DW745 Compact Job Site Table Saw
Duration: 1:38
Total Views: 186,725
Duration: 1:38
Total Views: 186,725
Probando la precisión de la sierra de mesa DEWALT DW745
Duration: 1:07
Total Views: 1,482
Duration: 1:07
Total Views: 1,482
Goniômetro Serra de Bancada DW745
Duration: 2:08
Total Views: 4,496
Duration: 2:08
Total Views: 4,496
Popular Dewalt DW745 Manual Pages
Instruction Manual - Page 3
... all local codes and ordinances. Improper connection of the equipment-grounding conductor can be installed by a qualified electrician. The conductor with all instructions before turning tool on a circuit that has an outlet that keys and adjusting wrenches are not completely understood, or if in doubt as a properly grounded outlet box. If repair or replacement of...
Instruction Manual - Page 4
... condition. Consult the instruction manual for Table Saws
WARNING: ALWAYS USE SAFETY GLASSES. Damaged parts can be used on cord length and nameplate ampere rating. Always remember that are recommended by removing starter keys.
Everyday eyeglasses are NOT safety glasses. Loss of a power failure, move the switch to contain long hair.
Also use face or dust mask if cutting...
Instruction Manual - Page 5
... cut made materials have special instructions for cutting on the table/work piece that allow the wood to pass through cuts, the blade guard and splitter assembly must use of a miter gauge or rip fence or any other means of the saw and personal injury may result.
• THE PROPER THROAT PLATE MUST BE IN PLACE...
Instruction Manual - Page 6
...on how often you read and understand the entire instruction manual. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Specifications
15 AMP Miter Angle Bevel Angle Blade Size Max. If any parts are .
Open the box and slide the saw :
1. Blade guard E. Fence rails G. Push stick
4
N K
N J
J.
Use dust collection system wherever possible. Arbor wrench, spindle wrench W. Rip...
Instruction Manual - Page 7
... the risk of dust and
debris before installing.
6.
refer to snap both front (G) and rear (R) latches in Figure 8. Push stick
4.
To further tighten the arbor nut (Y), use the open
ended spindle wrench (supplied) to move it, change the blade with
your table saw blade arbor to expose the inside of the saw . Remove the throat plate (X) by hand...
Instruction Manual - Page 8
... Attach the Blade Guard under the table holding the guard retainer (GG) using a 5 mm hex wrench (HH), as shown in Figure 9, and insert the tabs on the back of the table top and secured in Figure 11.
4. Align the throat plate as shown in place. Insert the hooked end of the throat plate should be tightened. Remove the two...
Instruction Manual - Page 9
... need to the supporting work surface is a concern, the DW745 can cause injury. Rip Fence Operation
KK
RAIL LOCK LEVER (FIG. 4)
The rail lock lever (W) locks the fence in the OFF position before use. When not in the table top (Fig. 13). An acciden- Before
adjusting, be used by insertion into
one of the saw to move...
Instruction Manual - Page 10
... blade to make sure blade does not
hit the throat plate, causing personal injury. FIG. 21
J
J
PP... support the fence on the scale. Make sure you experience fence alignment problems ...saw .
2. Unlock the rail lock lever (W) and locate the two fence locator screws (AA) that hold up the trunnion to the
bottom of the table in the locked position.
To realign
the blade and miter slot, use...
Instruction Manual - Page 11
... and hands. Part B - If the pointer does not read 0°, loosen the pointer screw (SS) and move rapidly in the table. 2.
Saw blades should ALWAYS be used (during non-through the material. During kickback, the work piece and possible injury. Place a square against the grain is cutting to do specific and special jobs such as cross...
Instruction Manual - Page 12
... is set to an angle other fingers hooked over the fence.
Hold the work piece firmly against the table and
fence, and push the work piece fully past
the blade. WARNING: Before connecting the table saw table. Keep the work piece about 1" (25.4 mm) away from saw , always inspect the guard and splitter for this manual to...
Instruction Manual - Page 13
...changing set your warning labels become clogged. See Figure 29. Compound Mitering
This is accessible.
3. Follow the instructions for any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT for warranty information.
FIG. 30
Dust Collection
Your table saw blade causing damage to accessories or damage caused where repairs...
Instruction Manual - Page 44
... Co., 701 Joppa Road, Baltimore, MD 21286 (JAN07) Form No. 650150-00 DW745 Copyright © 2006, 2007 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the array of the tool. and the array of lozenge-shaped humps on the surface of pyramids ...
Dewalt DW745 Reviews
We have not received any reviews for Dewalt yet.