EdgeStar BR3001BL Support Question
EdgeStar BR3001BL Support Question
Find answers below for this question about EdgeStar BR3001BL.Need a EdgeStar BR3001BL manual? We have 1 online manual for this item!
Question posted by ecuff on April 30th, 2023
My Digital Temp Adjustment Wont Move. How Do I Fix That?
My digital temp adjustment is not responding, neither is the F and C push button. Is there a way to reset or correct it?
Current Answers
Answer #1: Posted by SonuKumar on April 30th, 2023 10:07 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,800
Member since:
May 9th, 2021 Points: 16,617,800
https://www.powerequipmentdirect.com/manuals/2c15e0b001059a4f3632f6332a1849de.pdf
page 10 onwards
or
Check the temperature sensor: Make sure that the temperature sensor is properly connected and not damaged. A damaged temperature sensor may cause the unit to malfunction.
Reset the unit
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related EdgeStar BR3001BL Manual Pages
Owner s Manual - Page 4
... the Guardrail 5 Installing the CO2 Cylinder and CO2 Regulator 6 Installing the Keg Coupler-Tapping the Beer 7
OPERATING YOUR BEER DISPENSER Grounding Instructions Setting the Correct Pressure for the CO2 Regulator Setting the Regulator Dispensing the Beer & Draw Technique Beer Clean Glasses Understanding Beer Temperature Understanding the Temperature Control Setting Automatic...
Owner s Manual - Page 6
... plug with your hand from inside the cabinet removed set the beer dispenser on the power. Install the four screws to open the cabinet and push up
the openings for 8 hours before turning on its side. 2.
Align the bottom of the cabinet and match up on the top of the cabinet...
Owner s Manual - Page 7
... only required if the regulator does not have a gasket.
4.
When you decide to convert the unit into the CO2 cylinder valve and tighten with an adjustable wrench.
5. Although price will vary with care. Insert the CO2 tank into the regulator to cylinder attachment nut. Connecting the CO2 Cylinder to the CO2...
Owner s Manual - Page 8
...coupler is now tapped.
5. Now connect the beer line (from the coupler and push down until the gauge reads 12-14 PSI (for more information.
1. Remove the .... When connecting the beer line, it locks into the final downward position. After handtightening the nut, use an adjustable wrench to tighten the nut a bit further.
4. Close the door.
6. Please contact EdgeStar customer service online ...
Owner s Manual - Page 9
... CO2 that the plug is for Ale and Lager types of broken out CO2 to keep the CO2 level prescribed by the brewer. Setting the Correct Pressure for electrical current.
Plug your kegs from the power cord. Most breweries in over time more CO2 will reduce the risk of electric...
Owner s Manual - Page 10
...brief pull of the PRV ring to the gas cylinder:
1. Slowly turn the regulator adjustment screw until the desired pressure is shown on the output pressure gauge.
5. Note:... and turning counter-clockwise will permit gas to vent. Note: on the regulator, and if necessary re-adjust using step #2 until the pressure has equalized. Close the shut-off valve on the cylinder completely.
...
Owner s Manual - Page 11
... to 2/3 full.
5. Using a glass for anything else may leave residues that you to a 120V, 60Hz, 15Amp grounded outlet.
2. Let the glasses air dry in a dish rack. Open faucet handle quickly and completely and fill the glass to get rid of.
If water droplets cling to the glass or if spots show...
Owner s Manual - Page 12
...(vinegar-like or lemonlike) occurs after drinking your lines for warm spots along them, and adjust accordingly. Such thermometers are enclosed in poured beer appearing hazy or cloudy. The same holds true...as it travels through the system from the keg to the
Note: During summer months, adjust the temperature control to be placed in foaming. The foaming occurs because the pressure being ...
Owner s Manual - Page 13
...build up the excess water with a towel. However, if the door is not usually necessary to adjust temperature by the expanding and / or contracting of this case, turn off . Understanding the Temperature... cool a new warm kegerator.
Press the button again to switch between Fahrenheit or Celsius. Only use this mode after 24 hours. Press the F/C button to exit Deep Chill mode. The machine ...
Owner s Manual - Page 14
Adjust the temperature of clearance around the appliance.
In order to prevent vibration and noise, the refrigerator should be converted to an all the removed accessories ...
Owner s Manual - Page 16
... not cold - Improper draw technique
Handle not fully returned to close properly. Contaminated dispense system. Replace Beer Keg
TROUBLESHOOTING YOUR REFRIGERATOR The refrigerator is inserted correctly into the wall socket - Check that there is not in another appliance or furniture.
15 Check that neither are frozen. Food in either the air...
Similar Questions
Dual Zone Wine Cooler
dual zone wine cooler model # TWR325ESS one of the zones is not cooling , how to fix problem ???
dual zone wine cooler model # TWR325ESS one of the zones is not cooling , how to fix problem ???
(Posted by mel3976 2 years ago)
I Want To Turn 32 Bottle Wine Cooler Off? Where Is The Switch?
(Posted by pargazzi 3 years ago)
Wine Refrigerator Edgestar Cwr262dz
My unit has stopped cooling and the lights are flashing rapidly. Has the control board gone bad?
My unit has stopped cooling and the lights are flashing rapidly. Has the control board gone bad?
(Posted by jolesky 4 years ago)
Recommended Temp. For Wines
What are the recommended temp. for red and white wines.
What are the recommended temp. for red and white wines.
(Posted by genesan 6 years ago)
Running Too Cold After Thermostat Adjustment.
Which direction do you turn the adjustment screw to raise the temperature?
Which direction do you turn the adjustment screw to raise the temperature?
(Posted by dnastauf 8 years ago)