Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by sharsabel on June 30th, 2012
Where Does The Leveling Bracket Go
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... Property Damage: • Copper tubing is not tied into a water softening system. ICE MAKER INSTALLATION INSTRUCTIONS
To avoid electric shock, which can cause death or severe personal injury, disconnect the ... for water leaks.
The following items will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures fall...
User Manual - Page 2
... Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Qty 2
5. Plastic Clamp - Qty 1
11. Qty 2
6. Steel Clamp - Plastic Water Supply Tubing
4. Leveling Bracket Qty 1
8. Ice Maker
2. Qty 2
10. Use This Page to Identify Parts
1.
User Manual - Page 3
... inside compressor compartment (D), remove screws securing sound baffle to left condenser mounting bracket screw(s). Rotate while inserting tube until right side of shelf is out of hole. Slowly lift up and pull on back of refrigerator.
3 Peel off label covering ice maker hole.
7. Remove freezer shelf (some models).
3. Remove plugs from freezer (some...
User Manual - Page 4
... screws (5) you installed in one half turn with screw (6). Adjust leveling bracket (7) to level ice maker (1). With ice maker in Step 12.Tighten screws. Make sure connection is same at top and bottom. Ice maker is level when gap between freezer wall and ice maker is tight.
10. DO NOT tighten bracket. (Bracket will go and finger tighten nylon compression nut onto threaded end...
User Manual - Page 5
... or alcohol before applying clamps.
17.
NOTE: Clean back of cabinet with exterior condenser, reinstall condenser brackets and tighten down screws.
21. On models with two plastic clamps (9). 15. Reinstall freezer shelf in lower position. Set ice container (2) on shelf.
18. Finger tighten nylon compression nut onto threaded end of rear panel...
User Manual - Page 6
..., lower wire signal arm. (See ice maker front cover for on/off position of the refrigerator to your household water system. Slide ferrule (sleeve) into water valve inlet as far as shown.
7. NOTE: Water line kit number 5303917950, available from electrical power before making a full tray of 1/4 inch (6.4 mm) OD, copper tubing. Reconnect...
User Manual - Page 7
... the water supply valve to the closed position.
7 Empty the container and be turned off automatically when the ice container is full. Automatic Ice Maker Tips
Remember that is softened. Do not connect the ice maker to the water supply or
whenever the water supply is turned off. • The following sounds are normal when...
Similar Questions
How To Install Leveling Bracket On Fridgedaire Ice Maker
(Posted by micfair 9 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Where Does The Leveling Bracket Go On A Frigidaire Im115 Ice Maker
(Posted by dessmadt 10 years ago)
Leveling Bracket
do i hafta drill a new hole in the ice maker to mount the leveling bracket
do i hafta drill a new hole in the ice maker to mount the leveling bracket
(Posted by Anonymous-55495 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)