Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by micfair on June 9th, 2014
How To Install Leveling Bracket On Fridgedaire Ice Maker
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
...the softener may damage the ice maker, causing it greatly increases...install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in a kit from your dealer to allow movement for the supply line. • DO NOT install water supply tubing in areas where temperatures fall below freezing. • Connect the ice maker to the refrigerator. ICE MAKER INSTALLATION...
User Manual - Page 2
...Qty 2
5. Plastic Clamp - Screws - Qty 1
7. Leveling Bracket Qty 1
8. Water Valve - Use This Page to Identify Parts
1. Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Qty 1
9. Steel Clamp - Ice Container
3. Ice Maker
2. Water Inlet Tube - Qty 2
6. Qty...
User Manual - Page 3
....
6. Peel off label covering ice maker hole.
7. Push water inlet tube...ice tray rack from freezer (some models) by pushing shelf to cabinet (B).
8. Unplug refrigerator from hole.
5. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from inside compressor compartment (D), remove screws securing sound baffle to left condenser mounting bracket...
User Manual - Page 4
... will be tightened later.)
13. Ice maker is level when gap between freezer wall and ice maker is tight.
10. With ice maker in Step 12.Tighten screws. Tighten another one hand, plug ice maker connector into connector mounted on bottom of inlet tube. Make sure connection is same at top and bottom. Install adjustable leveling bracket (7) on back freezer panel. Make...
User Manual - Page 5
..., if installed. Locate factory punched holes at bottom right corner of water valve. Connect wiring harness to drive the two self drilling screws (4) through cabinet liner. Reinstall freezer shelf in lower position. Push plastic water supply tubing into cabinet.
19. DO NOT over tighten.
16. Holes are only drilled through bracket and...
User Manual - Page 6
...connecting the water supply line to the ice maker inlet valve. Discard ice made of 1/4 inch (6.4 mm) OD, copper tubing. Before Installing The Water Supply Line, You Will ...ice. DO NOT use a self-piercing type shutoff valve.
• A compression nut and ferrule (sleeve) for the water supply line. Slide ferrule (sleeve) into a water softening system. NOTE: Water line kit...
User Manual - Page 7
... wire signal arm is in its
“down” or ON position. The ice maker will hit the ice when the ice container is full. Empty the container and be turned off automatically when the ice container is full. To stop the ice maker, lift the wire signal arm until it clicks and locks in the “...
Similar Questions
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Where Does The Leveling Bracket Go On A Frigidaire Im115 Ice Maker
(Posted by dessmadt 10 years ago)
Where Does The Leveling Bracket Go
(Posted by sharsabel 11 years ago)
Leveling Bracket
do i hafta drill a new hole in the ice maker to mount the leveling bracket
do i hafta drill a new hole in the ice maker to mount the leveling bracket
(Posted by Anonymous-55495 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)