Fujitsu XG2600 Support Question
Fujitsu XG2600 Support Question
Find answers below for this question about Fujitsu XG2600.Need a Fujitsu XG2600 manual? We have 2 online manuals for this item!
Question posted by m1esteinberg on June 28th, 2014
Admin Password
I bought a XG2600 switch from a bulk company auction and it has an admin password set so I can't log in to it. How do I reset that password via console
Current Answers
Answer #1: Posted by TrickyRicky65 on April 21st, 2019 6:18 AM
TrickyRicky65
Member since:
April 21st, 2019 Points: 110
Member since:
April 21st, 2019 Points: 110
Fujitsu XG2600 PASSWORD RESET PROCEDURE!!!! I figured it out!!! First, press the 'reset' pin-hole on the device before you plug power into the device. Plug power into the device. Continue holding the 'reset' for a few seconds only. Holding it too long will negate the process. On your computer, configure your network card ip address to 192.168.1.2 with subnet mask of 255.255.255.0. Plug in a network cable from your computer directly to the 'management port' on the device. Create a telnet session, I used putty, to 192.168.1.1. You should get a 'backup#' prompt. Type 'reset clear' with no quotes and press enter. The device will restart. I waited for the restart based on the led lights on the device. I had to do this because the device had just been reset, therefore it has no ip address anymore when it starts 'normally' with out the 'reset' being pressed. After it seemed like it had restarted, I unplugged the device from power. Disconnect the network cable from the 'management port'. These next steps were to confirm the device had been reset completely. Password and all! Connect the RS232 to rj45 conversion cable to the console port on the device. Connect the RS232 side of the conversion cable to your computer. I had to use a 9 pin serial to USB conversion cable and plugged that into a USB port on my computer. I did have to wait for my computer to 'recognize' the 'serial COM Port' that had just been plugged into a USB port. Plug power back into the device. Use a 'dumb terminal emulator', I used Termite, to initiate a console session. Configure the port for 9600,N,8,1 no flow control. You will get a 'Login:' prompt. Type 'admin' with no quotes and hit enter. You should get a 'Password:' prompt. Just hit enter' Viola!
Answer #2: Posted by TechSupport101 on June 28th, 2014 8:54 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. See page 35 of the Hardware Guide here http://www.helpowl.com/manuals/Fujitsu/XG2600/143065 for assistance with factory reset.
Related Fujitsu XG2600 Manual Pages
Hardware Guide - Page 1
XG2600 Hardware Guide Introduction
TA41001-7426
Hardware Guide
Hardware Guide - Page 2
... Corporation. This manual explains the procedures required to install your XG2600 and should be read and understood before you start using your XG2600. Copyright FUJITSU LIMITED 2011
2
XG2600 Hardware Guide
Preface
You have purchased the XG2600, a compact, 26 port 10 Gigabit Ethernet layer 2 switch that achieves unsurpassed standards of high throughput and low-latency performance...
Hardware Guide - Page 3
...connection with additional unit of the XG Series switch product or other intellectual property right ("Intellectual Property...repeated corrections or provision of information within reasonable limits as set forth in subsection (1) above, Fujitsu shall be liable for... such event, Fujitsu will not be non-infringing; XG2600 Hardware Guide
LICENSE AGREEMENT
Product Name
XG Series Basic Software...
Hardware Guide - Page 4
XG2600 Hardware Guide
c. if in Fujitsu's sole judgment it is not commercially reasonable to perform either of the above options, subject to the limitation of liability set forth above is... for any damages (including, but is not designed, developed and manufactured as otherwise expressly set forth in subsection (2) above, Fujitsu shall pay for any damages Customer has incurred due to...
Hardware Guide - Page 5
XG2600 Hardware Guide
Contents
Contents
Preface ...2 LICENSE AGREEMENT ...3 Organization and Usage of ...Items in the Package, Descriptions and Functions 18
1.1.1 Parts List ...18 1.1.2 Installation of Switch: Front Access or Rear Access (User Configured Airflow 19 1.1.3 Switch Fan Unit Side ...20 1.1.4 Switch Port Side ...22 1.1.5 Top Surface ...25 1.1.6 BOTTOM Surface ...26
1.2 Option ...27
...
Hardware Guide - Page 6
XG2600 Hardware Guide
Contents
2.3.4 Plugging in the USB Memory ...50
2.4 Connecting a Setup PC ...51 2.5 Time Setting ...55 2.6 Set up IP address ...56
Index...57
6
Hardware Guide - Page 7
... is required. Indicates cautionary notes related to Console PC. To use this device safely. This chapter describes how to install the switch and connect it to the Product Liability (P.L.)...Started
Chapter 2 Installation
Contents This chapter lists the items that must read the file. XG2600 Hardware Guide
Organization and Usage of This Manual
This manual explains what you must be ...
Hardware Guide - Page 13
... time may become damaged. Use of the device or upgrading the device firmware implies acceptance of the device.
13 Only use of the device is set a password. XG2600 Hardware Guide
Notes on the network can configure this device. Precautions for any purpose other than the original purchase price.
• Fujitsu and its partners...
Hardware Guide - Page 18
... to the rear side of the rack, and 2 screws for mounting the switch in a rack.
18
Items in the package.
‰ XG2600
‰ Power Cables (Qty 2)
‰ SFP+ Dummy Caps (Qty 26)
XG2600
‰ Console cable adapter
‰ Rack Mounting Rails (1 set ) Rails for fastening the switch (rack mounting brackets attached to the side of the...
Hardware Guide - Page 19
...switch to install the switch in the rack, depending on user's requirements.
19
Items in a PDF format) necessary for connecting the switch to equipment whose port side is facing forward such as other switches, routers...in a rack, which serves better for operating and configuring the switch.
XG2600 Hardware Guide
Chapter 1 Getting Started
• CD-ROM
It contains the Firmware and ...
Hardware Guide - Page 44
...air or nitrogen. Precautions
• Unplug both ends of the twisted pair cable from equipments (HUB, router, and workstation) during discharging operation.
• Do not use ground wire of SFP+ Module
1.... and conduct operation below for how to the switch. XG2600 Hardware Guide
Chapter 2 Installation
2.3 Connecting the Equipment
We recommend discharging static electricity of twisted pair ...
Hardware Guide - Page 46
...cable
Management port of cascading connection with other than auto negotiation.
XG2600 Hardware Guide
Chapter 2 Installation
2.3.3 Connecting Twisted Pair Cable /...+ slots only support 10Gbps full duplex mode fixed setting.)
Ports automatically apply to the maximum speed that .... Use the straight cable in case of the switch is set auto negotiation enable by the auto negotiation function....
Hardware Guide - Page 51
... fix them with the RS232 cable to connect the set up PC to the switch. Connect the RS232C cable and the console cable adapter which is used with the screw.
3. XG2600 Hardware Guide
2.4 Connecting a Setup PC
This is required to connect the set up PC to the switch. Chapter 2 Installation
Necessary Hardware / Software
Please prepare the...
Hardware Guide - Page 52
... change plug adapter. Connect the power cable to the power connecter of the switch.
# clear logging error #
Reference User's Guide "5.18.1.5 clear logging error" (pg.365)
• When turning off easily.
• Please connect the power cable in the following order.
XG2600 Hardware Guide
Turn on the Power
Chapter 2 Installation
Caution
• Please use...
Hardware Guide - Page 53
... PSU2 and PSU2 LED of PSU2. Set the setting conditions to the power connecter of the switch will light in the power cable to the following message may appear When pressing the [Return] key or [Enter] key.
XG2600 Hardware Guide
3. Next, plug in green.
Precautions
The following ; Key in password, then press the [Return] key...
Hardware Guide - Page 54
Confirm "#" is shown on screen.
If the key in the wrong password, "invalid password." Please repeat your process from item 5.
54
Connecting a Setup PC will be displayed, then the "Login :" will be displayed again. XG2600 Hardware Guide
Chapter 2 Installation
8.
Hardware Guide - Page 55
... "Jan 1, 2011 12:30:00am".
55
Time Setting XG2600# date 2011/01/01.12:30:00 Set time and date to be "-0500". XG2600 Hardware Guide
Chapter 2 Installation
2.5 Time Setting
Make sure to set at the initial timing of the switch. The time is not set up time manually using console or telnet.
XG2600(config)# save
Save the configuration. z Command...
Hardware Guide - Page 56
... ip" address command at the initial state of the purchase. Please set the IP address through console. • When logging in from
the console after setting up the IP address. • Please set at
the same time.
56
Set up IP address XG2600 Hardware Guide
Chapter 2 Installation
2.6 Set up the IP address (ex. 192.168.1.1)
z Command (When connecting through...
Quick Start Guide - Page 1
... required for purchasing the Fujitsu XG2600 10Gb Ethernet. Connect the switch console port to a host system using a serial
crossover cable (not supplied) and the serial-to-RJ45 cable adapter included with VT100 terminal emulation.
4. When the switch Ready LED stops blinking, login via the terminal
session:
Login: admin Password: [ENTER] weak admin's password: set the password XG2600# _
Quick Start Guide - Page 2
...This command prompts for a password password admin set
# Switch name sysname
# Set up the switch for selecting Fujitsu as your 10 Gigabit Ethernet switch provider. If rack mounting the XG2600, please carefully review the ...proper configutation m ay cause dam age to the device and/or property.
9. reset
7. The
switch is a two-man operation. CAUTION: Im proper handling m ay cause personal injury...
Similar Questions
Fujitsu Xg2600 Data Switch How To Reset Non-default Login/password Thru Console?
Fujitsu XG2600 data switch how to reset non-default login/password thru console?Sitting in front of ...
Fujitsu XG2600 data switch how to reset non-default login/password thru console?Sitting in front of ...
(Posted by motionctrl 5 years ago)
Reset Lost Admin Password For Fujitsu Fi-6010n
Hi there, I have a fujitsufi 6010N whose admin password is lost. How can i reset or recover the pass...
Hi there, I have a fujitsufi 6010N whose admin password is lost. How can i reset or recover the pass...
(Posted by cescarpa 7 years ago)
Default Admin Password Does Not Work
powered on scanner and the admin default does not work. can not log in to configure scanner.
powered on scanner and the admin default does not work. can not log in to configure scanner.
(Posted by ernestwoods 9 years ago)
Fujitsu Xg2600 Password Reset Question Was Answered
bought a XG2600 switch from a bulk company auction and it has an admin password set so I can't log i...
bought a XG2600 switch from a bulk company auction and it has an admin password set so I can't log i...
(Posted by m1esteinberg 9 years ago)
How To Reset Fi6010n Admin Password
(Posted by dabemyer 9 years ago)