GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by brwbondepalm on January 1st, 2014
Changing Telephone Numbers
Hi, i want to ask how to add or change telephone numbers in de alarmpanel
Current Answers
Answer #1: Posted by cursed on January 1st, 2014 9:16 AM
cursed
Member since:
November 27th, 2013 Points: 320,075
Member since:
November 27th, 2013 Points: 320,075
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...the touchpad, allow at least 3 inches below it past its stop point. A built-in an environmentally controlled area (32°F to 120°F/0°C to indicate the current status of compatible security ... knife for max- Tools and Equipment Needed
• 4-conductor, 22- Table 1: Touchpad Power Usage
Current (mA) 110
60 12
Conditions
Maximum alarm current with basic system operating...
Installation Instructions - Page 2
... the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5.
Remove panel AC and backup battery power. 2. Separating the Touchpad from the panel to the touchpad location (see Figure 3 for the touchpad door to the Mounting Plate
Align the tabs at the marked locations...
Installation Instructions - Page 3
... should show SCANNING BUS DEVICES, then display date and time.
3.
At the touchpad, enter program mode by pressing 8 + CODE + 0 + 2.
Alphanumeric touchpads briefly show the date and time display. Press ƒ. Press ƒ and the display shows SECURITY. 5. When using the ATP1000 as key beeps) see the specific panel installation instructions. To connect a programming...
Installation Instructions - Page 4
...
3. To correct this, change the touchpad unit number as described in step 3, there may be adjusted for lighting conditions in the section "Changing the Touchpad Unit Number." Press A or B ...connect a programming touchpad to a Concord panel with software versions 1.0-1.6:
To prevent a trouble condition, you must delete the programming touchpad unit number from Concord panel memory before...
Installation Instructions - Page 5
.... Check for correct wiring connections at touchpad and panel terminals.
2. Note At this page). (Concord panels with software versions 1.01.6 only.)
Changing the Touchpad Unit Number (Concord
Panels with Software Version 1.0-1.6 Only)
Use the following guidelines when changing device unit numbers to avoid communication conflicts between the touchpad and the panel begins immediately. The...
Installation Instructions - Page 6
...129;vphyÃT
6
ATP1000 Touchpad/Display Installation Instructions FCC Part 15 Information to the User
Changes or modifications not expressly approved by one touchpad, go to another system touchpad and enter 8 + installer/dealer... reception, which can be cleared. Concord is encouraged to try to separate outlets, on deleting unused unit numbers. Note If the panel still indicates...
Similar Questions
Change Security Code For: Ge Networx With Nx-1448e Keypad
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
I purchased a home that has a GE NetworX security system with a NX-1448E Keypad. How do I add/change...
(Posted by Jim39164 8 years ago)
Nx-1448e How Do You Change The Phone Number It Dials When It Alarms?
(Posted by hubbard007 8 years ago)
How To Change Date On Ativa At-p1000 Manual
(Posted by sajunksq 9 years ago)
How Do We Disarm Our System And When Do We Type In Security Code?
(Posted by carolyn2707 13 years ago)
How Do You Change The Time/date?
I need to change the time/date but the stupid instruction that came with the pad does not address th...
I need to change the time/date but the stupid instruction that came with the pad does not address th...
(Posted by res1wymz 13 years ago)