Genie Excelerator Support Question
Genie Excelerator Support Question
Find answers below for this question about Genie Excelerator.Need a Genie Excelerator manual? We have 1 online manual for this item!
Question posted by barnhartdorothy on February 24th, 2014
Genie Excerator Isd 990
I need item 12 carriage assembly
Current Answers
Related Genie Excelerator Manual Pages
Owner's Manual - Page 1
... Garage Door Opener Installation 12 Accessories 22 Maintenance 25 Troubleshooting 26 Wiring Diagram 29 Warranty information 30
COMPLETE WITH INTELLICODE® REMOTE CONTROL AND SERIES II ELECTRONICS
For 7' 6" Doors. Will not operate twice as fast on a one-piece door. Please call us: 1-800-35-GENIE (354-3643) www.geniecompany.com
Please have Model information ready when calling.
Need...
Owner's Manual - Page 2
... to which door spring parts are used for opening equipment may cause injuries, your safety and the safety of the door.
7 Install the entrapment WARNING label next to cables, spring assembly, and other like items.
• Repairs and adjustments must reverse when the door contacts a 1-1/2 inch high object on the floor at 1-800-35-GENIE..
each, are...
Owner's Manual - Page 3
... frame) must be braced or reinforced before installing Opener. C A door opener reinforcement bracket may be needed to connect garage door to Opener's Door Bracket. NOTE
The Excelerator Opener is equipped with frame and skin - Door should stay stationary. Make a note of whether it adjusted by a Genie Factory Authorized Dealer. This Opener is designed for installation on page 27...
Owner's Manual - Page 4
... center line. Bottom of the garage door opening. Do Not move the door spring. C Check wall for 8' door
Figure 3 Rail Extension Kit SECTIONAL DOOR
ONE-PIECE DOOR
Figure 4 Find Highest Point of doors: - If there is in your mark to open the garage door.
NOTE
• For both types of Travel
4
For Help, call 1-800-35-GENIE or visit www.geniecompany.com...
Owner's Manual - Page 5
... Opener Power Head: • If not, an outlet or wiring box must be mounted (Figure 5): A Measure from garage door center line mark toward rear
of garage: • Approximately 10' back if garage has a 7' 6" door. • Approximately 11' back if garage has an 8' 0" door. • Approximately 13' back if garage has an 10' 0" door. • Approximately 14' back if garage has an 12' 0" door...
Owner's Manual - Page 6
A If you open garage door from outside if there is highly recommended to install a Genie Emergency Release Kit (GER-2).
available from the garage door before starting the installation. A If your garage does not have a separate entry door, it is a power failure. (Please see Accessories Order Form on pages 31/32.)
Before going further, get any items and tools
needed for your...
Owner's Manual - Page 9
...Rail Section
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
9 Engage Hooks... door
11C. CAUTION
The Drive Screw and Rail Liner can slide out of Rail Sections. Finger-tighten until the Opener is needed...you have a 1-piece rail unit, skip Assembly Step 2. GARAGE DOOR OPENER ASSEMBLY
Assembly Step C1H: CONNECT RAIL TO POWER HEAD
OPEN BLUE PARTS BAG
A Turn Power Head upside ...
Owner's Manual - Page 12
... at mark above Garage Door
A If needed, attach a 2" x 6" board (Figure 18) (also see page 4) with 3 (1/4" x 2") Lag Screws.
26
Header Bracket
30
1/4" x 2" Lag Screws
55
5/16-18 x 3/4" Hex Head Bolts
11
5/16-18 x 3/4" Hex Serrated Flange Nuts
28
Door Bracket
56
1/4"-20 x 3/4" Self-Drilling Screws
Hardware (orange bag)
12
For Help, call 1-800-35-GENIE or visit...
Owner's Manual - Page 13
... lightweight materials must be properly braced before mounting door Opener. B Attach Door Bracket: • For metal doors, use 3 (1/4" -20 x 3/4") Self-Drilling Screws (provided). • For wood doors, use 3 (1/4" x 2") Lag Screws or 3 (1/4" x 11/4") Lag Screws (not provided). Installation SteCpH2: INSTALL GARAGE DOOR BRACKET
CAUTION
Doors made of Rail Strap Bolt through Header Bracket...
Owner's Manual - Page 15
.... D Adjust height of Emergency Release Cord Knob to 6' above floor: • Pull Cord through Magnetic Carriage Assembly Lever
until Knob is as short as possible. D Adjust height of children. C Attach both Arms together with garage door fully or partially open, garage door may leave Emergency Release Knob within reach of Emergency Release Cord Knob to 6' above ! Failure...
Owner's Manual - Page 16
... modules on this side whenever possible. • For multiple-door garages see (Figure 26). - Check if Bracket extends out from a Genie Factory Authorized Dealer or through the Accessories Order Form. - Blocks of Bracket is installed. Preventing crossed signals is No power to the Opener before installing Safe-T-Beam® System Wires. Installation SteCpH6: INSTALL...
Owner's Manual - Page 18
... with Entrapment Warning Label
18
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
C Ensure Vacation Lock Switch is in as far as needed to stop working.
B Find a convenient mounting location:
• Within direct sight of any moving garage door or Opener parts (you
should not be sure to only tap them in...
Owner's Manual - Page 20
.... Do not over -tighten.
• Re-engage Magnetic Carriage Assembly. B Setting Open Limit Switch:
• Manually open garage door to open )
Carriage (disengaged)
Magnet
Figure 34 Setting Limit Switches
Force Controls
HI LO HI LO OPEN CLOSE FORCE FORCE
Figure 35 Making Force Adjustments
20
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
Do not over -tighten...
Owner's Manual - Page 21
... Reverse
For Help, call 1-800-35-GENIE or visit www.geniecompany.com
21 F Adjust Close Force to minimum needed to Close Limit Switch. If your Excelerator® is blocked, door will prevent the Timer/Cycle Counter from resetting.
If not, adjust Close Force Control slightly clockwise, open garage door, and close garage door, and open position using Wall Console.
•...
Owner's Manual - Page 22
.... If programming has stopped, repeat the above . Cover snaps open or close the garage door if the Safe-TBeam® System is erased: • Program Remotes again as needed. C Press Button again.
You cannot use the door Opener, Remote Controls, or
Wireless Keypad. • Refer to the door and door Opener Owner's Manuals
before attempting any similar device. -
WARNING...
Owner's Manual - Page 23
... lens may need to be programmed to 8 characters).
• Press
.
- once per second and turns off . B Programming the Keypad for Multiple Door openers: All door openers will control the door for 30 seconds after the door starts moving , close the door and disconnect it from the Wireless Keypad.
(continued on next page)
For Help, call 1-800-35-GENIE or...
Owner's Manual - Page 26
... of severe injury or death. 7 KEEP GARAGE DOORS PROPERLY BALANCED. Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of travel, retest the Door Opener.
Any other wall console can cause the Opener to operate unexpectedly and the light to cables, spring assemblies, and other hardware.
8 SAVE THESE INSTRUCTIONS...
Owner's Manual - Page 27
...Connector on Controller Board. Check Wall Console Wiring for further assistance.
Have a Genie Factory Authorized Dealer check: -
Check Safe-T-Beam® Self-diagnostic System. ...Opener-unplug (or disconnect power), wait 5 seconds, plug
back in (reapply power), and activate from Opener. Check door condition. Ribbon Cable on Motor Drive Board is equipped with an automatic garage door...
Owner's Manual - Page 28
... Control codes from Remote Control
1. Replace as needed . • Check garage door for binding.
• Check Open Limit Switch for a short circuit and for proper wiring. • Check Open Force adjustment (see Wall Console Installation on page 18).
If Opener is connected to Rail Drive Screw (see Install Magnetic Carriage Assembly onto Rails on page 10).
• Check...
Owner's Manual - Page 29
... all fasteners are tightened. • Check that the garage door and Opener are in UNLOCKED position for any diagnostic codes. Door closes, and Opener shuts down
• Check position of Lenses. • Check Safe-T-Beam® System for service, or contact Customer Service at 1-800-35-GENIE. If present, troubleshoot as detailed in Safe-T-Beam®...
Similar Questions
Garage Door Opener Not Working
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
Green light and red light are on the safety"eye" When pushing wall, remote or key pad the screw driv...
(Posted by scanty5 9 years ago)
Is Genie Excelerator Garage Door Opener Compatible With The 3 Button Remote?
(Posted by ven1anubis 10 years ago)
Garage Door Opener.
The unit will not work from the wall remote. The wall remote lights up but does not operat the unit....
The unit will not work from the wall remote. The wall remote lights up but does not operat the unit....
(Posted by ckniffen 10 years ago)
Where Is The Learn Code Button Situated On The 3060l-07 Genie Garage Door Opener
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
Where is the learn code button situated on the 3060L-07 Genie garage door opener. Trying to intregat...
(Posted by katiaella 11 years ago)