Home » Haier » Air Conditioners » Haier HB2400VD1M20

Haier HB2400VD1M20 Support Question

Find answers below for this question about Haier HB2400VD1M20.
Need a Haier HB2400VD1M20 manual? We have 1 online manual for this item!

Haier Overview Questions Manuals Reviews Videos Research

Question posted by alisonhender on July 14th, 2013

What Is The Size Of The Filter To Use?

The person who posted this question about this Haier product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Haier HB2400VD1M20 Manual Pages

User Manual - Page 1

... SHOULD BE USED WHEN INSTALLING OR MODIFYING THIS APPLIANCE, UNLESS OTHERWISE NOTED IN THESE INSTRUCTIONS. SOME LOCALITIES MAY REQUIRE THE INSTALLER/SERVICER TO BE LICENSED. No. 0010572323 F AUTOMOBILE, SPACE HEATER, WATER HEATER,ETC.) INSURE THAT THE ENCLOSED AREA IS PROPERLY VENTILATED. Installation & Operation Manual Air Handler 13 SEER 2 Ton Models: HB2400VD1M20 HB2400VD1V20 WARNING...

User Manual - Page 2

... APPLIANCE IS NOT APPROVED FOR OUTDOOR INSTALLATION THIS APPLIANCE IS NOT TO BE USED AS A CONSTRUCTION HEATER GENERAL This appliance was designed certified and must be... Code Prior to shipment, this appliance was tested and inspected for connection to air distribution ductwork. 2 Should questions arise contact the local EPA office. INDEX TOPIC General Physical dimensions Replacement Parts...

User Manual - Page 4

... or flame capable of vehicles. When more than one appliance is available. This secondary drain pan is required in the event that it is properly sized and adequate power is installed in a building, permanently identify the unit as to the drain lines in garages, ware houses or other areas where they...

User Manual - Page 5

... pan when unit is installed in unconditioned i.e. (Garage, Attic ) application, or downflow applications, and install insulation kit on vertical ( donut shape ) drain pan. *Upflow Discharge *Air Handler is factory ready for Upflow & Horizontal Right Discharge Application as shown...

User Manual - Page 6

...-hand side. Traps must be installed on the primary drain and on the secondary drain if used. 8) In all cooling applications, a secondary drain pan must be placed in its left horizontal... the assembly completely to the user. 9) WARNING: The "A" coil contains 150 p.s.i.g. Fig.2 6 Air flow Secondary Knockout Primary Knockout Important: Drain pan must be tested for field brazing see page 12 ...

User Manual - Page 7

... in inches of a condensate removal pump is required. A joint compound should be used not to the air handler. The unit and the auxiliary drain pan must be supported or routed to ... pump should a blocked drain occur. When using copper tubing as a lubricant. Use of water, as measured in the return duct. Do not reduce the recommended tubing size. To avoid damage that will prevent damage to...

User Manual - Page 8

Copper wire is only for "HB" air handlers installed without a heat kit. 8 Blower running Over-current Motor Ampacity 208/230 FLA 208/230 HB2400VD1M20 -------- 15/15 0.9 Blower Motor H.P. 1/8 HB2400VD1V20 ... disconnect means should be in accordance with local codes, or in that kit. The use of the unit, when required by code. The ampacity and overcurrent protection shown above ...

User Manual - Page 9

... COM TO OUTDOOR UNIT R,C,Y,O TRANSFORMER Diagram 2 3. Note: Thermostat C : COM. OR YL RD BL BL 24V COM O YCR TO OUTDOOR UNIT R,C,Y,O TRANSFORMER For Thermostat only control Air Diagram 1 Conditioning open /stop , hot control Environment temperature, can adopt different power switch show diagram 2. Above diagram: Outdoor Unit Connection Left: Indoor and Outdoor unit...

User Manual - Page 10

... switch show diagram 5. R : AC24V TERMOSTAT Y : COMPRESSOR G Y R C G : FAN For detailed Thermostat, please connect corresponding terminal according to above control specification. For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring diagram as shown diagram 4. This mode is control the indoor unit & cooling only outdoor unit at the same time no...

User Manual - Page 11

... an unconditoned space it is recommended to match the outdoor unit capacity. Supply air ducts must be insulated and return ducts must be replaced before any tubing connections...Torque the 13/16 nut to the liquid tube. 7) Insert the suction line into position. The use of flexible duct connectors is correct. These connectors must be changed to minimize the possibility of the ducts...

User Manual - Page 12

...filter) 4% reduction for differences encountered in installations. The CFM can be checked by the following method; (The optional Heat Kit must be done by changing the blower speeds. This can be done in the heat mode. 3) Measure the return air.... Model Static Pressure 0.1 CFM 0.15 0.2 High 900 877 856 HB2400VD1M20 Middle 630 614 599 High 900 877 856 HB2400VD1V20 Middle 630 614 599...

User Manual - Page 13

... serious personal injury or death. It is cleaned or replaced. START-UP Prior to initial start-up insure that a return air filter grille be obtained from vehicular or other services. 13 Retrun and supply ducts are properly sized and tightened. All panels must be present. Unit is not to insure that the circulating...