Hamilton Beach 14506 Support Question
Hamilton Beach 14506 Support Question
Find answers below for this question about Hamilton Beach 14506.Need a Hamilton Beach 14506 manual? We have 1 online manual for this item!
Question posted by hd105dm on September 3rd, 2023
Settings On The Dial
My iron setting is faded on the hamilton beach iron, model 14506, series A5131DA. I would like picture of the fabric locations on the dial?
Current Answers
Answer #1: Posted by SonuKumar on September 3rd, 2023 10:34 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,648,060
Member since:
May 9th, 2021 Points: 16,648,060
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hamilton Beach 14506 Manual Pages
Use & Care - Page 2
...the cord to or greater than the maximum rating of electric shock, do not disassemble the iron. The iron must be used by or
near children. Close supervision is required for storing. 5. If an...extension cord is connected or on the same circuit with an ampere rating equal to disconnect the iron from the electrical outlet. Care shall be taken to arrange the cord so that the surface
on ...
Use & Care - Page 3
... after a few uses.
• To clean steam vents before first use, prepare iron for steam ironing and then iron over an old cloth for household use of electric shock. Shock Hazard: This appliance has...8226; Do not use vertical steam in any other surface may appear to clean the vents. WARNING! Ironing on page 10.
840226100 ENv02.indd 3
3
1/21/13 9:21 AM Do not defeat the safety...
Use & Care - Page 4
Parts and Features
Spray and Steam Burst Buttons
Adjustable Steam Switch
Soft Touch Grip
Cord Retraction Button Heel Rest
Water Tank Cover
Cord Retraction Button
Spray Nozzle
Temperature Control Dial
Retractable Cord
Soleplate
4
840226100 ENv02.indd 4
Self-Clean Button
1/21/13 9:21 AM
Use & Care - Page 5
NOTICE: Do not unwind the cord past the red tape.
2
3
4
Set the Adjustable Steam Switch to reach desired temperature. Allow 2 minutes for iron to (Dry Iron).
Resting on either side Resting on heel
30 seconds or 15 minutes depending on soleplate
30 seconds
5
To turn iron off, turn off automatically when left in the following...
Use & Care - Page 6
... iron on a lower temperature setting or failing to allow hot soleplate to reach desired temperature. OR
4
Turn Temperature Control Dial to desired fabric setting in hot water dripping from the soleplate.
5
Set Adjustable Steam Switch to the desired steam level.
6
6
6
For vertical steaming, hold iron 6 inches (15 cm) from garment and do not allow the iron to preheat for iron...
Use & Care - Page 7
...
30 seconds or 15 minutes depending on exact orientation
Resting on the iron's position. How to Steam Iron (cont.)
7
To turn off , set Adjustable Steam Switch to (Dry Iron).
8
Turn the Temperature Control Dial to OFF.
Unplug iron and let cool.
9
Empty water from iron following positions. The Auto Shutoff time varies based on heel
15 minutes...
Use & Care - Page 8
... 9:23 AM Garment Label Symbols
Fabric care labels on wrong side. Fabric Setting Chart
NOTICE: To avoid garment damage, check garment label for fabric composition and ironing instructions.
For linen, iron fabric on wrong side.
These symbols are shown below along with an explanation of their meaning.
Iron
High
Medium Low Temp
Temp
Temp
Setting
Setting
Setting
Do not iron
Do not...
Use & Care - Page 9
...
Never use abrasive
cleaners or metal scouring pads, since they may scratch the soleplate surface. • Allow the iron to cool and wipe with your other hand to the iron soleplate: • Never iron over sink until water runs out. Soleplate Care
NOTICE: To avoid damage to retract the cord. RETRACTABLE CORD
CAUTION...
Use & Care - Page 10
Self-Clean Feature
To keep the steam vents clear of any buildup, follow these instructions each time you iron using steam.
1
2
3
4
Turn Temperature Control Dial to OFF.
Unplug iron.
5
Hold iron over sink.
10
840226100 ENv02.indd 10
6
Press and hold the Self-Clean Button until tank is empty.
1/21/13 9:23 AM Turn the...
Use & Care - Page 11
... Off function activated? This will not allow steam when temperature setting is leaking. Troubleshooting
PROBLEM Iron won 't steam. Twisted cord.
PROBABLE CAUSE • Is iron plugged in the middle of the iron cord.
• Choose correct temperature setting for your fabric.
• Adjust temperature to desired setting. Did the iron have enough time to preheat? • If dry...
Use & Care - Page 12
.... All liability is no longer available, we will replace with the printed directions, or damage to any other warranty or condition.
For faster service, locate the model, type, and series numbers on the rating label (e.g., 120V ~ 60 Hz). This warranty extends only to products purchased and used for all claims for special, incidental...
Similar Questions
Wire Replacement
How do I replace the power cord on a Hamilton Beech steam iron model 14506?
How do I replace the power cord on a Hamilton Beech steam iron model 14506?
(Posted by jdsage39 1 year ago)
I Have A Retractable Iron Model#14289 The Cord Got Stuck Have Way How Do I Fix I
I have a retractable iron model#14289 the cord got stuck have way how do I fix it?
I have a retractable iron model#14289 the cord got stuck have way how do I fix it?
(Posted by Juliecamacho70 2 years ago)
Iron Model 14553 Series A4331da
I purchase this item from walmart a couple months ago i did not kept my receipt or box since it had ...
I purchase this item from walmart a couple months ago i did not kept my receipt or box since it had ...
(Posted by luv8luv 7 years ago)
Have An 14506 Chrome Iron. Had It About 5 And A Half Months. The Water Fill Lid
(Posted by jcherry300 10 years ago)
Why Does The Blue Light Not Go Off When The Iron Is Turned To 'off?'
I have just purchased a 14506 Hamilton Beach steam iron. I would like to leave the iron plugged in a...
I have just purchased a 14506 Hamilton Beach steam iron. I would like to leave the iron plugged in a...
(Posted by c2cwalker 10 years ago)