Hamilton Beach 14506 Support Question
Hamilton Beach 14506 Support Question
Find answers below for this question about Hamilton Beach 14506.Need a Hamilton Beach 14506 manual? We have 1 online manual for this item!
Question posted by bn1600 on August 28th, 2018
Iron Not Getting Heated
working iron suddenly stopped and not getting heated up. Power source checked and ok
Current Answers
Answer #1: Posted by Odin on August 28th, 2018 10:33 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
See the first-listed PROBLEM at https://www.manualslib.com/manual/446121/Hamilton-Beach-14506.html?page=11&term=trouble.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Hamilton Beach 14506 Manual Pages
Use & Care - Page 2
...leaking. Care shall be taken to or greater than the maximum rating of electric shock when the iron is not in use . 2. SAVE THESE INSTRUCTIONS!
2
840226100 ENv02.indd 2
1/21/13 ...9:21 AM Do not let the cord touch hot surfaces. Coil the cord loosely around the iron for any appliance used . IMPORTANT SAFETY INSTRUCTIONS
When using your flatiron, basic safety precautions should always be ...
Use & Care - Page 3
...first use of electric shock. This will stop after a few uses with tap water. If the plug does not fit fully into a polarized outlet. Ironing on an ironing board. Then follow the self-cleaning instructions... are being worn.
• Do not use only. This will stop and does not indicate a defect or hazard.
• Many irons spit or sputter during the first few uses.
• To clean...
Use & Care - Page 5
...
MOTIONLESS TIME
Resting on soleplate
30 seconds
5
To turn Temperature Control Dial to OFF.
Allow 2 minutes for iron to desired temperature. POSITION SENSING/AUTO SHUTOFF
The iron will turn off , turn iron off automatically when left in the following positions. NOTICE: Do not unwind the cord past the red tape.
2
3
4
Set the Adjustable...
Use & Care - Page 6
... hot water dripping from the soleplate.
5
Set Adjustable Steam Switch to the desired steam level.
6
6
6
For vertical steaming, hold iron 6 inches (15 cm) from garment and do not allow the iron to preheat for iron to reach desired temperature. NOTICE: Do not unwind the cord past the red tape. Allow 2 minutes for 2 minutes can...
Use & Care - Page 7
... time varies based on heel
15 minutes
840226100 ENv02.indd 7
7
1/21/13 10:53 AM
POSITION SENSING/AUTO SHUTOFF
The iron will turn iron off automatically when left in "Care and Cleaning." IRON POSITION
MOTIONLESS TIME
Resting on soleplate
30 seconds
Resting on either side
30 seconds or 15 minutes depending on exact...
Use & Care - Page 8
...
8
840226100 ENv02.indd 8
1/21/13 9:23 AM Steam Setting
Dry Iron
Temperature Setting
OFF
Synthetics
•
Low
Silk, Wool
••
Medium
Ironing Instructions
OFF
Dry iron using spray if necessary. Fabric Setting Chart
NOTICE: To avoid garment damage, check garment label for fabric composition and ironing instructions.
These symbols are shown below along with an explanation...
Use & Care - Page 9
... hand to retract the cord. Soleplate Care
NOTICE: To avoid damage to the iron soleplate: • Never iron over sink until water runs out. Eye Hazard: Hold the plug with one ....
RETRACTABLE CORD
CAUTION!
Care and Cleaning
1
Allow iron to cool.
2
To empty water from iron, open the water tank cover and slowly tilt pointed end of iron over zippers, buttons, pins, metal rivets, or snaps...
Use & Care - Page 10
... Self-Clean Button until tank is empty.
1/21/13 9:23 AM Turn the Temperature Control Dial to Cotton-Linen ••• setting and let iron heat for 2 minutes. Self-Clean Feature
To keep the steam vents clear of any buildup, follow these instructions each time you...
Use & Care - Page 11
... in tank may discolor clothing and soleplate.
• If the iron cord should become twisted, unplug iron and let cool. Iron leaves spots on clothing. Twisted cord. Check outlet by plugging in and the outlet working?
Move or tilt the iron to reset. • Do not overfill the water tank. • Adjust steam to desired setting...
Similar Questions
Wire Replacement
How do I replace the power cord on a Hamilton Beech steam iron model 14506?
How do I replace the power cord on a Hamilton Beech steam iron model 14506?
(Posted by jdsage39 1 year ago)
Iron Wont Stop Beeping
My iron wont stop beeping when plugged in and it flashes red
My iron wont stop beeping when plugged in and it flashes red
(Posted by angiereds08 7 years ago)
Have An 14506 Chrome Iron. Had It About 5 And A Half Months. The Water Fill Lid
(Posted by jcherry300 10 years ago)
Why Does The Blue Light Not Go Off When The Iron Is Turned To 'off?'
I have just purchased a 14506 Hamilton Beach steam iron. I would like to leave the iron plugged in a...
I have just purchased a 14506 Hamilton Beach steam iron. I would like to leave the iron plugged in a...
(Posted by c2cwalker 10 years ago)
My Iron 14890 Stopped Heating And Warrenty Has Just Ran Out What Do I Do To Get
fixed please advise
fixed please advise
(Posted by rrrufussy 13 years ago)