Honeywell T8011 Support Question
Honeywell T8011 Support Question
Find answers below for this question about Honeywell T8011.Need a Honeywell T8011 manual? We have 1 online manual for this item!
Current Answers
Related Honeywell T8011 Manual Pages
Owner's Manual - Page 1
T8000, T8001,T8002, T8011, T8024 Programmable Thermostats
OWNER'S GUIDE
1
6699-1-1443311-1-1
Owner's Manual - Page 2
... of power failure.
• Indefinite temperature hold. • Preprogrammed for your new Honeywell programmable thermostat. Features
• Program up to four time periods with temperature settings to a comfortable level of...your convenience. • Backlit display (select models).
2
69-1431-1 Your new programmable thermostat is designed to the world of heating or air conditioning.
Owner's Manual - Page 3
... Time and Day ...8 Setting Weekday Program ...9 Setting Weekend Program ...10 Setting Temporary Temperature Hold 13 Setting Indefinite Temperature Hold 13 Operating Thermostat ...13 Setting SYSTEM and FAN Switches 13
Replace the Batteries (T8002 Only 14 Backlighting (Select Models 14 Minimum Off-Timing ...15 Troubleshooting ...16 Customer Assistance ...19 Warranty ...20
3
69-1431...
Owner's Manual - Page 4
... TIME. • PROGRAM SELECTIONS.
T8000, T8001
PM
T8011, T8024
TUE
MODELS
Hold
Select
PM TUE
Hold
Select
T8002 MODEL
AuFtoANOn
FAN SWITCH
CoolSOYfSf THEeMat
HOLD KEY • SET TEMPORARY TEMPERATURE HOLD.
SELECT KEY • CURRENT SETPOINT. • CHANGE DAY AND TIME. • PROGRAM SELECTIONS. BATTERY DOOR
SYSTEM SWITCH
M14673
4
69-1431-1 HOLD KEY...
Owner's Manual - Page 5
... for weekdays and weekend.
The thermostat can use the program schedule to program the thermostat, it uses the preprogrammed time and temperature settings in the weekday and weekend times and temperatures you decide not to plan your program.
Preprogrammed Time and Temperature Settings. Planning Program Schedule
The thermostat display shows day, time, program period...
Owner's Manual - Page 7
...during heating season, and a lower temperature during cooling season.)
Return is the time the thermostat turns on the outside temperature and your equipment response
7
time, to give the equipment ..., depending on the heating/cooling equipment after an energy saving period. Programming Thermostat
The thermostat is flexible and can set for an energy-saving temperature while you arrive home...
Owner's Manual - Page 8
... the preprogrammed time and temperature (see Table 1), press Hold to set current time, press Select twice. To set current day.
M12591A
8
69-1431-1
Sleep is displayed.
2. PM
While setting the current time, the word SET is the time period you are sleeping. (For more comfortable sleeping, some people choose not to...
Owner's Manual - Page 9
A flame (heating) or a snowflake (cooling) appears in the right side of the display, when setting the program temperature.
3. Leave
a. M18566
b. Press ▲ or ▼ to set
Leave
SET
temp-
erature.
5. M12625C
9
M18567
69-1431-1 Press ▲ or ▼ ...
Owner's Manual - Page 12
The thermostat reverts to indefinitely hold a temperature. M18556
Setting Temporary Temperature Hold
1. Setting Indefinite Temperature Hold
The Hold key allows you to displaying SET the current day ..., press Hold twice. Hold can be canceled by pressing the Hold key again.
1. Programming is displayed. Press ▲ or ▼ key to set a temporary
temperature setting. TEMPORARY
PM
NOTE:...
Owner's Manual - Page 13
... setpoint. Off: Both the heating and cooling are off. Em. Compressor is on continuously). Slide the SYSTEM switch in the lower left corner of the thermostat to select the desired fan setting. Terminal L is energized continuously (fault heat relay is deenergized. FAN settings: Auto: Fan operates with equipment.
NOTE: In the...
Owner's Manual - Page 14
... battey power.
14
69-1431-1
As the batteries run out completely.
it is blank when changing batteries, reset the time and day. If the display is stored permanently! Back Lighting (Select Models)
Any key pressed lights the display for one to two months before the batteries run low, your thermostat shows a "bAt Lo" message in the digital...
Owner's Manual - Page 15
If the compressor turns off when the setpoint is changed, the minimum off-timer is changed.
A flashing flame or snowflake indicates the minimum off-time is in first stage heating or cooling on the T8011 (heat pump model). The minimum off-timer operates in cooling on again for at least five minutes after it...
Owner's Manual - Page 16
... if the switch at the equipment is mounted and latched on the wallplate-mount and latch the thermostat on . Temperature settings do not change (example: cannot set to the On position. • Check if the batteries are good and installed correctly
(T8002 only).
• Check that the temperature setpoints are: between 40 to...
Owner's Manual - Page 17
... system to respond. • Set SYSTEM switch to Heat. • If the temperature setting is higher than the current room
temperature and the flame is displaying, the thermostat is operating correctly.
Troubleshooting (Continued). Action
• Check if the circuit breaker is tripped-reset the circuit breaker.
• Check if the fuse is...
Owner's Manual - Page 18
... system to respond. • Set SYSTEM switch to Cool. • If the temperature setting is lower than the current room
temperature and the snowflake is displaying, the thermostat is in the Off
position-set to On position. • Wait five minutes for assistance.
Symptom Cooling does not come on.
Action
• Check...
Owner's Manual - Page 19
... minutes until the minimum off -timer is complete. Customer Assistance
If you have any questions concerning the operation of your thermostat, please visit us at www.honeywell.com or call the thermostat information helpline at 1-800-468-1502.
19
69-1431-1 Action Wait a couple minutes after seeing the flame or snowflake and...
Owner's Manual - Page 20
... a short description of the malfunction, and mail it (at Honeywell's option) within a reasonable period of a consumer.
20
69-1431-1
Warranty
Honeywell warrants this product, excluding battery, to the following address: Honeywell Return Goods Dock 4 MN10-3860 1885 Douglas Drive North Golden Valley, MN 55422
This warranty does not cover removal or...
Similar Questions
Screen On Touchscreen Thermostat Has Ee. Changed Battery And Flicked Circuit Bre
breaker but will not work. What to do? Model GH8320U1008
breaker but will not work. What to do? Model GH8320U1008
(Posted by ljones5706 11 years ago)
Display Keeps Clicking Even After Circuit Breaker Was Reset.
(Posted by Karencharny 11 years ago)
Keypad Displays But Can't Change Anything. Nothing Happens When I Press Buttons.
Never had problem before. Have changed batteris.
Never had problem before. Have changed batteris.
(Posted by ktbowen45 12 years ago)