Icom IC-7300 Support Question
Find answers below for this question about Icom IC-7300.Need a Icom IC-7300 manual? We have 1 online manual for this item!
Question posted by gary91025 on August 15th, 2023
Ic 7300 Problem With Alc
Current Answers
Answer #1: Posted by SonuKumar on August 15th, 2023 9:44 PM
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #2: Posted by khanjee on August 15th, 2023 9:46 PM
Both transceivers are very similar. The first setting to look at is the USB MOD Level. Currently mine is set to 30% in the 7610. It works well with all of the software programs I use, Ham Radio Deluxe DM780, WSJT-X, WinWarbler and Fldigi.
In the 7300 it is in Menu>Set>Connectors. Look for USB MOD Level. Try 40% in this radio.
In the Icom 7610 go one menu deeper to MOD INPUT. Try around 30% - 40%.
Icom 7300/7610 MULTI KnobThis is where the RF power is adjusted and it's the only setting needed to increase or decrease RF power output. Using this method the ALC will stay the same whether running 10 watts, 50 watts or 100 watts.
Push the MULTI knob and select RF POWER with the touch of a finger. Rotate the MULTI knob and set you RF power to the desired setting. Mine is normally around 30% and I get 30 watts output.
Please Accept my answer by providing you with the best possible solution. Would be more glade.
THANK YOU
Answer #3: Posted by HelpHero on August 16th, 2023 10:29 PM
1. Begin by checking the ALC settings in the transceiver's menu. Press the MENU button on the IC-7300 and select "SET" to access the settings menu. Navigate to the "OPTION" menu and ensure that the ALC function is enabled. If it is disabled, enable it and see if the ALC issue is resolved.
2. Verify that the ALC settings for your operating mode are properly configured. Different modes (such as SSB, AM, FM, etc.) have specific ALC requirements. Ensure that the ALC gain is correctly adjusted for the mode you are using.
3. Check the microphone input level. Make sure the microphone gain is set appropriately. If the gain is too high, it can cause an ALC problem. Adjust the microphone gain to a suitable level and observe if the ALC issue persists.
4. Examine the microphone connection. Ensure that it is securely plugged into the correct microphone input jack on the transceiver. Loose or improper connections can cause ALC issues. If you're using a 4-pole microphone plug, be certain it is correctly inserted into the transceiver.
5. Test the microphone on another device, such as a computer or another transceiver, if possible. This will help determine whether the issue lies with the microphone itself or the IC-7300 transceiver.
6. If the above steps did not resolve the ALC problem, consider updating the firmware of your IC-7300. Firmware updates can sometimes address known issues and improve overall performance. Visit the Icom website for firmware update instructions and follow them carefully.
7. If none of these steps resolve the ALC issue, it may be necessary to contact Icom customer support or consult with a professional technician for further assistance. They can provide additional guidance and potentially perform repairs if required.
Always exercise caution and refer to the manufacturer's instructions when working with electronic devices like the IC-7300.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers.
Helphero
Related Icom IC-7300 Manual Pages
Similar Questions
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
The problem I have with the Icom IC-7600 on all the bands 10 -80 meters I get 100 watts out. On 160 ...