Icom IC-A220 Support Question
Icom IC-A220 Support Question
Find answers below for this question about Icom IC-A220.Need a Icom IC-A220 manual? We have 1 online manual for this item!
Question posted by michaelp1190 on June 27th, 2023
Icom A220 Raio
ICOM a22 radio stuck / frozen on the ICOM logo on the display. Will not complete the boot/ power on cyce
Current Answers
Answer #1: Posted by SonuKumar on June 27th, 2023 9:00 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,622,390
Member since:
May 9th, 2021 Points: 16,622,390
If your ICOM A22 radio is stuck or frozen on the ICOM logo during the boot/power-on cycle and doesn't complete the process, there are a few troubleshooting steps you can try to resolve the issue:
- Reset the radio: Locate the small reset button on the radio. It is usually a small hole labeled "RESET" on the front or back panel. Use a paperclip or a small tool to press and hold the reset button for a few seconds. This action will reset the radio's settings to their default values and might resolve the issue.
- Remove power and batteries: Turn off the radio and remove any external power source, such as the battery pack or power adapter. Leave the radio disconnected from power for a few minutes to allow any residual charge to dissipate. Afterward, reconnect the power source and try turning on the radio again.
- Update the firmware: Visit the ICOM website and check if there are any firmware updates available for your A22 radio. If there are updates, follow the instructions provided by ICOM to update the firmware. Updating the firmware can often resolve software-related issues.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Icom IC-A220 Manual Pages
Instruction Manual - Page 2
...Icom logo are designed to provide reasonable protection against harmful interference when the equipment is likely to radio communications. This in accordance with the limits for the IC-A220 and IC-A220E...er des interférences perturbant les communications radio. IMPORTANT
FCC INFORMATION
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver. SAVE THIS INSTRUCTION ...
Instruction Manual - Page 3
... electric
blasting caps or in excessively dusty envi-
DO NOT use by this radio is DC fused at high volume levels.
If you experience ringing, reduce the... Continuous high volume operation may damage the transceiver.
CAUTION: NEVER connect the transceiver to a power source using
reverse polarity.
The transceiver will be damaged. Accidental reverse connection will damage the ...
Instruction Manual - Page 5
...; DO NOT transmit for use time ("50% duty cycle"). SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards.This radio is within the FCC allowable limits for and classified as worst case, the antenna shall...
Instruction Manual - Page 7
... iv INFORMATION EN MATIÈRE DE SÉCURIT v TABLE OF CONTENTS vi
1 PANEL DESCRIPTION 1 ■ Front panel 1 ■ Rear panel 2 ■ Function display 3 2 BASIC OPERATION 4 ■ General description 4 ■ Receiving and transmitting 5 ■ Directly setting the frequency 6 ■ Squelch settings 6
3 MEMORY OPERATION 7 ■ General description 7 ■...
Instruction Manual - Page 8
... in the Configuration menu (p. 22) is set the emergency frequency (121.5 MHz). (p. 15)
e VOLUME/POWER SWITCH [VOL] ➥ Turn [VOL] to switch the power ON or OFF. ➥ Adjusts the audio output level.
The volume level bar is displayed while rotating [VOL]. ➥ Hold down for two seconds to enter the direct frequency...
Instruction Manual - Page 9
...for available GPS receiver details. w D-SUB 25 PIN CONNECTOR Connect a 13.8 V or 27.5 V DC power supply, speaker,
headset and third party GPS receiver*. Refer to 'AUTO.' w
cy setting mode. (p. 6) ... mode. (p. 15)
o OUTER (Large) TUNING DIAL [O-DIAL]
Rotate to enter a displayed frequency
into any blank regular memory channel or delete or revive
the selected memory channel (depending on...
Instruction Manual - Page 10
... when opening the active frequency's squelch
memory mode. (p. 8)
function. (p. 5) r INTERCO3M READOUT
!0 SQUELCH MODE READOUT Displays the squelch mode status. (pp. 6, 20)
Displays "ICS" when the intercom function is also displayed if the name has been
entered. ➥ Displays "HISTORY" when the history memory chan- lected. (p. 13)
(p. 18)
• A third party GPS receiver is...
Instruction Manual - Page 11
There are two ways to set the frequency, activate the frequency, and receive or transmit. Set the ...(pp. 7-13) When you can directly enter the desired frequency.
Enter the direct frequency setting mode.
erating frequency in the standby frequency display. Then ex-
Receive/transmit
4 Refer to "MEMORY OPERATION" for details.
• Set the frequency normally • Set the frequency ...
Instruction Manual - Page 12
... too loudly. NOTE: To prevent interference, listen on the frequency
before transmitting. RX
126.40 134.805
4. Receiving
When receiving a signal, "RX" is displayed and audio is displayed. • DO NOT hold the microphone too closely to select the desired frequency as the standby frequency. • The active frequency is clear.
5 Otherwise...
Instruction Manual - Page 13
...005
AU
squelch mode.
• "RX" and " TEST" disappear and the squelch test function is displayed.
cy setting mode.
• Only the active frequency is
turned OFF.
• MN (manual): ... item in the Settings menu. (p. 21)
eeWhen receiving a signal, "RX" is RX
displayed and audio is displayed.
• DO NOT hold the microphone too closely to your signal. eeRepeat q through w to...
Instruction Manual - Page 15
...the memory mode. • T he memory channel number is
MEMORY
118.00 127.005
CH01
displayed.
• T he memory channel name is the only option.)
DONE Returns to the standby frequency...) Sets the channel tag to the selected memory channel. (Selecting the group memory channel is also displayed if it has been en-
They contain the following items.
REPLACE (p. 9) Enter the selected memory...
Instruction Manual - Page 16
... channels
To enter frequencies into the channel. • "WRITE COMPLETED" is displayed when the regular memory channel is also displayed if it has been entered.
eeRotate [DIAL] to select...frequency
for two seconds to enter the memory mode. • The memory channel number is displayed. • T he memory channel name is entered. DDClearing the memory contents
You can clear...
Instruction Manual - Page 17
... channel name. rrPush [MEM]. • The channel name's 1st digit blinks.
DDEntering group names
(For only group memory channels) The memory groups can display a six character name in addition to the memory number. wwRotate [DIAL] to select a desired channel. MEMORY OPERATION 3
DDEntering channel names
(For only regular...
Instruction Manual - Page 18
... shown to select "CH TAG." yyHold down [RCL] to set the memory group. GRP01
122.00 127.005
CH01
TWR
Channel tag list
TAG
DISPLAY
NAME Group*1 GPS*2
MEANS
_ _ _ YES
-
User1 setting (p. 24)
U-2 YES
- User2 setting (p. 24)
*1Group memory, *2GPS memory
About U-1/U-2 You can be set the channel tag.
ww...
Instruction Manual - Page 20
qqPush [RCL] to enter the memory mode.
NOTE: The GPS memory data is displayed. qqPush [RCL] to enter the memory mode. wwRotate [O-DIAL] to the GPS memory (maximum 10 memory channels). *Ask your dealer for available GPS receiver ...
Instruction Manual - Page 23
...DUAL], rotate [VOL] to turn ON the transceiver's power. • Configuration menu is displayed. CAUTION: Use of 8.33 kHz Channel Spacing of this
radio is displayed. • Y ou can set the headphone output level...This function manually opens the squelch for two seconds to enable the intercom
function. • "ICS" is strictly prohibited and shall not be used in the menu mode. ttHold down [...
Instruction Manual - Page 33
... A
05
06
D MBA-3 rear panel adapter
The rear panel adapter compatible with card edge connector.
Approved Icom optional equipment is not included.
Dimensions: 200 (W) × 200 (H) × 300 (D) mm
7.9 ...power supply
Provides convenient operation of the transceiver on the ground. The transceiver is designed for the destruction or damage to an Icom transceiver in the event the Icom...
Instruction Manual - Page 34
...;1.3 (H)✕10.7 (D) inches
• Weight (approximately): 1.0 kg; 2.2 lb
DDTransmitter
• Output power: IC-A220 IC-A220E • Spurious emissions: IC-A220 IC-A220E • Microphone impedance: • Modulation limiting: IC-A220 IC-A220E
8 W (Carrier power) 6 W (Carrier power)
-60 dBc -36 dBm (harmonics) - 46 dBm (non-harmonics) 600 ø
70...
Instruction Manual - Page 35
... the display example between 118.0000 MHz and 118.1000 MHz. 8 SPECIFICATIONS (VFO CHANNEL ID LIST)
• Selectivity (with 8.33 kHz channel spacing):
IC-A220
6 dB ±2.778 kHz
60 dB ±7.37 kHz
IC-A220E
6 dB ±2.8 kHz
• Spurious response rejection:
IC-A220
More than 74 dBµ
IC-A220E
More than 70 dB
• Audio output power...
Instruction Manual - Page 40
A-7210D-1EX-q Printed in Japan © 2015 Icom Inc. Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Similar Questions
How Can I Open The Ic 7200 For Transmission On Marine Channels?
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
I have been adviced that it is possible to modify so that I for safety reasons only, can trx on mari...
(Posted by Runeedamm 5 months ago)
A220 Radio- New Out Of Box - Station Reported That Frequencies Were Manually Pro
when powered on display stuck in ICOM (NO Frequencies displayed)
when powered on display stuck in ICOM (NO Frequencies displayed)
(Posted by BarneyPhillips 11 months ago)
Icom A220t, I Can't Hear My Self When I Make A Radio Call, But The Tower Can H
Hi I can't hear myself when I make a transmission, but the receiver (tower) can can hear me loud and...
Hi I can't hear myself when I make a transmission, but the receiver (tower) can can hear me loud and...
(Posted by Info59647 1 year ago)
