Home » LiftMaster » Garage Door Openers » LiftMaster TAC1

LiftMaster TAC1 Support Question

Find answers below for this question about LiftMaster TAC1.
Need a LiftMaster TAC1 manual? We have 1 online manual for this item!

LiftMaster Overview Questions Manuals Reviews Videos Research

Question posted by eizzy on February 23rd, 2013

Alarm Ringing

When my gates open sometimes there`s a ringing alarm how do i delete the alarm?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related LiftMaster TAC1 Manual Pages

TAC1 Manual - Page 1

Elmhurst, IL 60126-1196 www.liftmaster.com TAC1 Telephone Entry System 1 23 456 789 0 Installation and Programming Manual The Chamberlain Group 845 Larch Ave.

TAC1 Manual - Page 2

... a Gate Operator (Normally Open) and a Maglock (Normally Closed) Wiring a Door Strike Lock (Normally Open) Wiring a Maglock (Normally Closed) Earth Ground Rod Power Wiring Plug the Transformer into the Outlet Mount the Unit Set the Unit Master Code 3 3 3 3 4-11 4 4 5 6 6 7 7 8 8 9 9 10 10 11 11 11 TESTING Test the Gate/Door Relays Test the Telephone Connections PROGRAMMING From the TAC1...

TAC1 Manual - Page 3

... for conflicts between the information listed in the above table and the requirements of local building codes. See Power Wire Table Below From the door strike, maglock or gate operator From the strike power supply (if needed) From the Earth ground to processor board Residence and Telco phone lines From the processor...

TAC1 Manual - Page 4

... Status LED 11 Power Status LED 12 Relay 1 (Primary) Output Status LED 13 Relay 2 (Secondary) Output Status LED 4 IMPORTANT NOTE: Both the back panel and TAC1 unit must be oriented and mounted in the upright position as shown at right and on the installation warning label. Mounting Surface DESCRIPTION OF THE...

TAC1 Manual - Page 5

... Tip sPyosstiètimone (dN'aolat rPmroevided) (non fourni) Home Phone 5 Use ONLY one HOUSE TELCO wire per hole. Typical Telco Overview Home Phone Ring Tip Alarm System Position (Not Provided) Telco Entrance Box Demarcation Point Typical Telco Overview With The Unit NOTE: If the unit will not function properly. Refer to...

TAC1 Manual - Page 6

WIRING THE UNIT WITH A TELCO LINE Ringer Equivalence Number (REN) = 5 RING TIP RING TIP PHONE LINE Telco Entrance Box Demarcation Point Ring Ring Tip Tip Ring Ring Tip Tip Telco WIRING THE UNIT WITHOUT A TELCO LINE The unit can be a stand alone system that allows communication between the unit and the resident's ...

TAC1 Manual - Page 7

... COM RELAY 2 RELAY 1 COM (Common) NO (Normally Open) WIRING AN AUTO-CALL SENSOR The Auto-Call feature will enable.... 12 AUTO CALL NO (Normally Open) 7 Primary Gate Operator (Strike Open Input) Loop Detector Loop Sensor INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) AND WIRING AN AUTO-CALL SENSOR WIRING A GATE OPERATOR (NORMALLY OPEN) The gate operator can be connected to Relay ...

TAC1 Manual - Page 8

... unit's power supply for information about configuring Relays 1 and 2. INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) A DOOR STRIKE LOCK (NORMALLY OPEN) AND WIRING A GATE OPERATOR (NORMALLY OPEN) & A MAGLOCK (NORMALLY CLOSED) WIRING A GATE OPERATOR (NORMALLY OPEN) & A DOOR STRIKE LOCK (NORMALLY OPEN) The door strike can be connected to Relay 1 or Relay 2. RELAY 2 RELAY 1 NOTE...

TAC1 Manual - Page 9

...Wire connectors can be connected to Relay 1 or Relay 2. See the Programming section for the door strike. RELAY 2 RELAY 1 COM (Common) NC (Normally Closed) 9 AC or DC Power... Relays 1 and 2. INSTALLATION >> WIRING A DOOR STRIKE LOCK (NORMALLY OPEN) AND WIRING A MAGLOCK (NORMALLY CLOSED) WIRING A DOOR STRIKE LOCK (NORMALLY OPEN) The door strike can be removed to Relay 1 or Relay...

TAC1 Manual - Page 10

... Existing Electrical System Electrical Panel Ground to the unit only. Rm Eug. M anu. 2 Rm Dedicated 10 Amp Minimum Circuit Breaker 12 Vac Power (included) The TAC1 MUST be grounded. POWER WIRE TABLE DISTANCE Under 30 feet 30 - 75 feet 75 - 150 feet 150 - 250 feet 250 - 500 feet AC POWER WIRE...

TAC1 Manual - Page 11

... back panel before the bottom of the unit is used to unlock the programming functions of the TAC1. The Master Code is in a secure location. Example: 1234. NOTE: The star (*) button acts as ...a User Code. NOTE: Once power is applied, the TAC1 will begin to click to indicate that will end any call, programming or access code key sequence. 11...

TAC1 Manual - Page 12

... AND TEST THE TELEPHONE CONNECTIONS TEST GATE/DOOR RELAYS TEST RELAY 1 Enter 4 digit Master Code + 1 (Key). NOTE: Relay 1 status indicator LED will illuminate (Blue) to show activity when triggered. TEST THE TELEPHONE CONNECTIONS 1. The TAC1 will blink during transmission. 3. To test Relay 2 have someone answer the telephone and enter "*5" (Star + 5). Place a telephone call...

TAC1 Manual - Page 13

... Master Code: ? ? ? ? Enter the Master Code: ? ? ? ? 2. Enter the Output Time (in a secure location. Enter the Program Code: 0 2 5 ENABLE PARALLEL RELAY OUTPUT (DEFAULT) 1. PROGRAMMING >> FROM THE TAC1 KEYPAD 12 3 GENERAL INSTRUCTION 456 789 0 NOTE: Use the STAR Key "*" to hear the visitor at the unit, 1 = Low, 2 = Medium and 3 = High. Stop and go...

TAC1 Manual - Page 14

...DELETE USER CODE NUMBERS 1. Enter the Relay/Channel for the Code to engage Party Mode on channels one and two. Enter the Program Code: 5 2 DISABLE VACATION (LOCK DOWN) MODE 1. Enter the Program Code: 1 TRIGGER RELAY 2 AND CHANNEL 2 1. ENTER A TEMPORARY (1 SHOT) USER CODE NUMBER The TAC1... party mode: Enter a valid code into the TAC1 keypad or enter "*5" into the local telephone. ...

TAC1 Manual - Page 15

... command tone: 1 0 2. ENABLE CALL FORWARDING Enter the command tone: DISABLE CALL FORWARDING Enter the command tone: 0 1 0 2 15 Enter the ring count: 2 through 5 ENABLE TELCO MODE Enter the command tone: 0 7 ENABLE STANDARD (LONG) RING TONE Enter the command tone: 1 4 ENABLE ALTERNATE DTMF PROGRAMMING This feature changes the first programming digit from to a 14...

TAC1 Manual - Page 16

... learn button on telco line, if 9 or 5 is clear (about the location of the relays is activated the TAC1 will emit a 315 MHz signal to the gate or door operator manual for each LiftMaster door or gate operator that receiver is successful. Press and release the learn button on the receiver will be controlled (2 maximum...

TAC1 Manual - Page 17

...Relay One and Radio Channel One 2 Trigger Relay Two and Radio Channel Two 7 Delete User Code 9 Enter User Code 03 Enable Intercom (No-Telco) Mode 04 Enable... Relay 2 AUDIO FEEDBACK FROM THE TAC1: 1 Low Tone Beep = Failure 2 Two High Tone Beeps = Valid sequence 3 Low Tone Beep = Error or invalid sequence NOTE: Use the STAR Key "*" to be deleted (4 digits) Master Code (4 digits...

TAC1 Manual - Page 18

... Call Forwarding Number Enter Call Forwarding Telephone Number # FACTORY SETTING Disabled Disabled Disabled PROGRAMMING PROCEDURE **01 **02 **03 **06 Disabled 5 Disabled Enabled Enabled **07 **#8 **10 + Ring Count (2-5) **13 **14 **15 **16 *# + Telephone Number (Up to 14 digits) + # DIRECT COMMANDS FROM THE LOCAL TELEPHONE PROGRAMMING DESCRIPTION OF TASK NUMBER FACTORY PROGRAMMING PROCEDURE...

TAC1 Manual - Page 19