Makita VC4710 Support Question
Makita VC4710 Support Question
Find answers below for this question about Makita VC4710.Need a Makita VC4710 manual? We have 4 online manuals for this item!
Question posted by fishbowl8d on December 28th, 2023
Trying To Remove Motor On Makita Vc4710 Vacuum
cant find a service manual for this vacuum
Current Answers
Answer #1: Posted by SonuKumar on December 29th, 2023 11:17 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,310
Member since:
May 9th, 2021 Points: 16,619,310
Removing the motor on a Makita VC4710 vacuum cleaner can be a tricky task, but it's definitely doable with the right instructions and tools. Here's a step-by-step guide to help you out:
Tools you'll need:
Phillips screwdriver
Flathead screwdriver (optional)
Socket wrench and appropriate socket sizes (refer to your vacuum's manual for specific sizes)
Pliers (optional)
Steps:
Unplug the vacuum cleaner and empty the dustbin. Make sure there's no debris or dust left inside.
Remove the hose and attachments. Disconnect the hose from the vacuum body and set it aside. Remove any other attachments like the wand and floor nozzle.
Open the dustbin compartment. Locate the screws or latches that hold the dustbin compartment in place and remove them. Carefully lift the compartment out of the vacuum body.
Disconnect the electrical wires. Look for the wires connected to the motor terminals. Carefully detach them using pliers or your fingers. Make sure to note the color coding of the wires so you can reconnect them correctly later.
Unscrew the motor mounting bolts. Locate the bolts that hold the motor in place. Depending on your model, there might be two or three bolts on the top and bottom of the motor housing. Use the appropriate socket wrench to loosen and remove these bolts.
Carefully remove the motor. Once the bolts are removed, you should be able to gently pull the motor out of the vacuum body. Be careful not to damage any wires or components as you do this.
Here are some additional tips:
Take pictures of the disassembly process at each step. This will help you reassemble the vacuum cleaner correctly later.
Consult your vacuum cleaner's manual for specific instructions and diagrams that might be relevant to your model.
If you're not comfortable with DIY repairs, it's always best to consult a qualified appliance repair technician.
I hope this helps! Let me know if you have any other questions.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Makita VC4710 Manual Pages
VC4710 Instruction Manual - Page 3
Contents
Makita VC4710
1 Safety instructions 2 Before starting the
cleaner
3 Control /Operation
4 Applications ...substances 16 4.1.2 Picking up liquids 16
5.1 Switching the vacuum cleaner off and storage 17
6.1 Maintenance plan 18 6.2 Maintenance work 6 Maintenance
7 Troubleshooting 8 Technical data
4
2.1 Assembling the vacuum cleaner 10 2.1.1 Taking accessories out of the packaging 10...
VC4710 Instruction Manual - Page 4
...servicing. • This vacuum cleaner is necessary when used by the cord, use with wet hands. • Do not put any opening blocked; If the vacuum is
not working as it should always be followed, including the following:
READ ALL
INSTRUCTIONS
BEFORE USING
VC4710... or contact your local Makita factory service center. IMPORTANT SAFETY
INSTRUCTIONS
When using the vacuum cleaner for the first ...
VC4710 Instruction Manual - Page 5
... anything that is burning or smoking, such as gasoline or use . See grounding instructions. • Tool should be turned off all parts of body away from openings and moving parts.
• Turn off... liquids can be found in chapter 2.3. • Connect to this Receptacle. Makita VC4710
WARNING
• Keep loose clothing, hair, fingers, and all controls before placing switch in the auto...
VC4710 Instruction Manual - Page 6
... electrician or service person if you are in the tank. 3.
Do not tilt the vacuum if there is liquid in doubt as specified by a qualified electrician.
6
Original Instruction Check with the appliance - Store vacuum in a risk of the equipment-grounding conductor can result in a dry place.
WARNING
Improper connection of electric shock. Makita VC4710
Purpose...
VC4710 Instruction Manual - Page 7
...illustrated.
Original Instruction
7 Makita VC4710
WARNING
This appliance is for the vacuum to cool down and start...Makita factory service center.
As an extension cord, only use the version specified by the manufacturer or one of the vacuum, wait for use on the vacuum corresponds with this appliance. This vacuum is equipped with a thermal cut out, check that nothing blocks the motor...
VC4710 Instruction Manual - Page 8
Makita VC4710
Electrical components
DANGER
Electric shock due to unsuitable supply voltage. by your Makita factory service center. Contact with live components.
...the operating instructions to the tool to the upper section of different appliances can result in damage.
1. The appliance can result in a tool, always switch off the vacuum cleaner and the tool that the voltage shown ...
VC4710 Instruction Manual - Page 9
... operating manual. Only use spare parts and accessories from Makita. 2. CAUTION
Picking up can lead to the environment.
1. Materials picked up environmentally hazardous materials. Vacuuming up ... up by the vacuum cleaner: - The following materials must be picked up liquids Spare parts and accessories Emptying tank
Original Instruction
Makita VC4710
WARNING
Hazardous materials....
VC4710 Instruction Manual - Page 10
... clamps
A
(A) and remove the upper section of
the tank and the packaging. P - 79865 W6084
P - 78293
P - 70297
10
Original Instruction Take the accessories out of the vacuum.
3. Makita VC4710
2 Before starting the cleaner
2.1 Assembling the
vacuum cleaner
2.1.1 Taking accessories out
of the packaging.
2.
ries out of the packaging
A
1. Take vacuum and accesso-
VC4710 Instruction Manual - Page 11
... of
the vacuum. tion firmly on to the inlet fitting.
5. ing clamps fit properly. A
A
6. Original Instruction
11
Ensure that the vacuum is
switched off and unplugged.
2. Attach the upper section of the vacuum
cleaner.
3. Press the filter bag connec- Be sure that the retain- 2.2 Preparing for dust pick-up: Inserting the filter bag
A
Makita VC4710
1.
VC4710 Instruction Manual - Page 12
... up : Empty container
A
1. Makita VC4710
2.3 Preparation for wet pick-up , always remove the filter bag/ disposal bag.
4. Be sure that the retaining
clamps fit properly.
12
Original Instruction Attach the upper section of the vacuum clean- Ensure that the vacuum is
switched off and unplugged.
2. er.
3. Open the retaining clamps
A
(A) and remove the upper section of...
VC4710 Instruction Manual - Page 13
...
0 auto
1. min rent tasks.
3 Control / Operation
Makita VC4710
3.1 Connections 3.1.1 Connecting the suction
hose
1. Connect the suction hose.
3.1.2 Electrical connection
The operating voltage shown on the rating plate must correspond to the voltage of the power supply.
3.2 Switching on the vacuum
3.2.1 Switch "auto-0-I
Auto On/Off
On / manual mode
Switch position
Function
max The...
VC4710 Instruction Manual - Page 14
... on the operating panel of the vacuum.
5. Makita VC4710
3.2.3 Auto-On/Off-Operation - To comply with a suction hose.
4. Switch off , the vacuum continues to run for a short moment so that the tool connected to the vacuum cleaner outlet is switched off the vacuum.
3. Connect the power tool and the vacuum with regulations, only approved tools should be connected. When the...
VC4710 Instruction Manual - Page 15
Makita VC4710
10 sec . We recommend complete cleaning if the filter element becomes extremely dirty.
1. Switch off the vacuum. 2.
Turn the switch to position "I" and let the vacuum operate for vacuum cleaning without the filter bag. 3.3 Cleaning the filter element 3.3.1 Cleaning the filter
element "Auto-Filter Cleaning System"
Only for ap-
Original Instruction
15
Close the...
VC4710 Instruction Manual - Page 18
... the upper section of the vacuum cleaner.
3. Close the retaining clamps
A
A
(B). Open the retaining clamps (A)
A
and remove the upper sec- Before reinserting the suction hose: clean the inlet fitting and hose collar. After finishing work
Any other maintenance than
described in chapter 6 should be
A
performed by Makita factory service
center.
6.2.1 Emptying the tank
After...
VC4710 Instruction Manual - Page 19
... vacuum before refitting them.
Original Instruction
19 The material collected must be reduced. Attach the upper section of in the intermediate ring and the upper section of the vacuum cleaner. Be sure that the retaining
clamps fit properly. If the seal or groove is switched off and unplugged.
2. Close the retaining clamps
A
A
(A).
A
Makita VC4710...
VC4710 Instruction Manual - Page 20
... bag in accordance with the slider. 5. Press the cardboard collar
of
the vacuum.
10. Close the retaining clamps
A
(A). Ensure that the vacuum is
switched off and unplugged.
2. Makita VC4710
6.2.4 Replacing the filter bag
A
1. er. C B
A
Removing the filter bag: 3. Open the retaining clamps
A
(A) and remove the upper
section of the filter bag in the
tank. 8. Clean the...
VC4710 Instruction Manual - Page 21
... (D) with applicable regulations. er. Carefully remove the disposal bag connection from the inlet fitting (C).
5. Dispose of the vacuum clean- Check that the retaining
clamps fit properly. Original Instruction
21 Be sure that the vacuum is
switched off and unplugged.
2. 6.2.5 Replacing the disposal bag
A
Makita VC4710
1. B D
C
Removing the disposal bag:
3. Close the disposal...
VC4710 Instruction Manual - Page 22
... elements. Attach the upper section of the vacuum clean- B
1. Removing the filter elements: 3.
Makita VC4710
6.2.6 Replacing filter element (Auto-Filter Cleaning System)
A
Never use the vacuum without a filter. For safety and extended life of the vacuum.
7. Open the retaining clamps
A
(A) and remove the upper
section of
the vacuum cleaner.
10.Close the retaining clamps...
VC4710 Instruction Manual - Page 23
....
cleaning
• Switch off the vacuum cleaner
tripped.
not be started again, contact
the Makita service department.
• Motor does not run in accord- suction ...tool
tic mode
connected properly. rating must be performed by yourself. section of filter element.
• Seal between tank and upper • Replace seal.
7 Troubleshooting
Makita VC4710
Fault • Motor...
VC4710 Instruction Manual - Page 24
...pickup X
24
Original Instruction Makita VC4710
8 Technical data
MAKITA VC4710 US
Voltage Mains frequency Current ... bag (5 pcs.) Anti-static hose 1 - 3/8" x 16" Crevis tool
Basic accessories order no . Description HEPA filter elements (2 pcs.)
Optional accessories...for appliance socket Total connected load Air flow rate (max.)
Vacuum Sound pressure level at a distance of 1 m, EN 60704...
Similar Questions
Makita Hr5001c Motor Problem
The motor runs at correct rev's but drops a slight bit of rev's every revolution but then picks up.C...
The motor runs at correct rev's but drops a slight bit of rev's every revolution but then picks up.C...
(Posted by tim50103 7 years ago)
Looking At The Sanding Pad Which Way To Remove The Hex Bolt. Clock Or Anticlock
(Posted by atsmith7 8 years ago)
Motor Housing
Please anyone could forword the actual outside diametre of the motor housing. Thank you in advance
Please anyone could forword the actual outside diametre of the motor housing. Thank you in advance
(Posted by Wombat73 11 years ago)
Is There A Step By Step Procedure To Remove And Replace The Pressure Switch.
makita MAC5200 I removedthe old switch. It fell apart in several peices and I do not know how to re...
makita MAC5200 I removedthe old switch. It fell apart in several peices and I do not know how to re...
(Posted by mryan31320 11 years ago)