Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by bhJoto on August 20th, 2014
Why Is My Gm-5500t Flashing Power Light
The person who posted this question about this Pioneer product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 3
... and injury, including burns.
! Do not use of the separately sold with accessories sold battery wire or the amplifier fuse blows. Check the connections of the power supply and speakers if the fuse of the car stereo while the en- This unit is short-circuited. ! Determine and resolve the cause, then replace the fuse...
Owner's Manual - Page 4
... or improper connection.
!
If distortion occurs when the car stereo volume is turned up, turn the gain control to higher level.
5 Power indicator The power indicator lights up , turn these controls to a level appropriate for...frequency selectable from 40 Hz to 500 Hz if the LPF select switch is set amplifier gain control to higher level. ! When the full range speaker is turned down.
...
Owner's Manual - Page 5
English
Section
02
En 5 Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted with little increase in power. Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain of the...
Owner's Manual - Page 6
... speaker connection instructions.
Never cut the insulation of the power supply to feed power to the power terminal via the ignition switch (12 V DC), the amplifier will remain on with metal parts in -
If the car stereo lacks a system remote control terminal, connect the male terminal to other amplifier connections, finally connect the battery wire terminal of...
Owner's Manual - Page 7
...for stereo connection, or 4 W to 8 W for monaural and other amplifiers, please follow the speaker output connection diagram for bridging shown on rear: two 8 W speakers in parallel for a two-channel amplifier, ...output (Stereo)
1 2
1 Speaker (Left) 2 Speaker (Right) One-channel output
1
1 Speaker (Mono)
En 7 Subwoofer
Speaker channel Two-channel output One-channel output
Power
Nominal input...
Owner's Manual - Page 8
... the speaker input wire
Connect the car stereo speaker output wires to the amplifier using the terminal screws, there is recommended. After completing all other amplifier connections, finally connect the battery wire terminal
1 Lug (sold separately) 2 Battery wire 3 Ground wire
4 Connect the wires to the terminal. Twist
Connecting the power terminal
The use of a special...
Owner's Manual - Page 9
... about 10 mm (3/8 in.) of the speaker wires to the speaker output terminals.
Connecting the units
Section
03
English
1 System remote control terminal 2 Ground terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire
Connecting the speaker output terminals
1 Use wire cutters or a utility knife to strip the...
Owner's Manual - Page 10
... get caught in the sliding mechanism of the seats or touch the legs of the driver's seat. ! Secure the amplifier at the imprints either on the carpet or directly on the car model.
Firstly make an imprint where the installation holes are behind the panel and protect all cables and important equipment...
Owner's Manual - Page 11
.../6 dB/12 dB Gain control: RCA 200 mV to 6.5 V Speaker 0.8 V to
modifications without notice. ! The average current drawn is input. mum current drawn by multiple power amplifiers.
En 11 Specifications and the design are subject to 26 V Maximum input level / impedance: RCA 6.5 V / 22 kW Speaker 26 V / 22 kW
CEA2006 Specifications...
Similar Questions
My Pioneer Gm-5500t Audio Inputs Are Not Working Help
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
(Posted by jddubray 4 years ago)
If You Are Using A Pioneer Gm-5500t Amp With A Single Channel Input Will It Run
full power mono?
full power mono?
(Posted by Chanpjkae 9 years ago)
Power Light Flashing
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
My power light is flashing. It was working fine and now it doesnt i checked the connections, they se...
(Posted by ntl1993 12 years ago)
Power Light Flashing
Why is the power light flashing and amp not working
Why is the power light flashing and amp not working
(Posted by kenstudebaker71 12 years ago)