Ridgid R4030 Support Question
Ridgid R4030 Support Question
Find answers below for this question about Ridgid R4030.Need a Ridgid R4030 manual? We have 1 online manual for this item!
Question posted by stingerdew on January 6th, 2013
I Need A Stand !
Hello . Do you have a stand for RIDGED 7 in. TILE SAW R4030 ?
Current Answers
Related Ridgid R4030 Manual Pages
Operation Manual - Page 1
OPERATOR'S MANUAL
7 in. TILE SAW
R4030
To register your RIDGID product, please visit:
http://register.RIDGID.com Pour enregistrer votre produit de RIDGID, s'il vous plaît la visite:
http://register.RIDGID.com Para registrar su producto de RIDGID, por favor visita: http://register.RIDGID.com
Your tile saw has been engineered and manufactured to our...
Operation Manual - Page 2
TABLE OF CONTENTS
Introduction...2 General Safety Rules...3-4 Specific Safety Rules...5 Symbols...6 Electrical...7-8 Features...9-10 Tools Needed...10 Loose Parts...11 Assembly...12-17 Operation...18-21 Adjustments...22-23 Maintenance...24-25 Warranty...26 ...
Operation Manual - Page 3
...tools sharp and clean for which it was designed.
USE RIGHT TOOL. Consult the operator's manual for alignment of moving parts, binding of tile... of the tool, a guard or other part that may risk injury.
NEVER STAND ON TOOL. Keep proper... it for . Feed work when practical, it on the saw 's applications and limitations as well as the specific potential hazards...
Operation Manual - Page 4
... rotating wheel.
INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.
GROUND ALL TOOLS. If repair or replacement of your saw or workpiece before connecting to remove cut material when wheel is the equipment-grounding conductor. If tool is equipped with or without yellow stripes is moving parts during use.
NEVER...
Operation Manual - Page 5
... saw OFF and disconnecting the saw before operating. f) Do not fill water bath above water fill line.
SAVE THESE INSTRUCTIONS. To reduce your hand to move into the cutting tool.... guide or fence.
NEVER stand or have the following markings:
a) Wear eye, hearing, and breathing protection. Wash hands after handling. c) Disconnect saw from the power source.
IF...
Operation Manual - Page 6
...orbits etc., per minute
6 - English SYMBOLS
The following symbols may be used on this tool.
NOTICE:
Without Safety Alert Symbol) Indicates important information not related to an injury hazard,...damp locations.
Proper interpretation of risk associated with side shields marked to operate the tool better and safer. Eye, Ear, & Breathing Protection
Always wear eye protection with...
Operation Manual - Page 7
... circuit and has a grounding plug similar to reduce the risk of least resistance for the tile saw does not operate when plugged into a matching outlet that are identified by Underwriter's Laboratories (UL) should be provided on lumber, tools or other obstructions while you are not completely understood, or if in doubt as to...
Operation Manual - Page 8
... at your local retailer. WARNING:
To reduce the risk of the tool plug or outlet getting wet, position tile saw to prevent water from dripping onto the outlet or plug. Do not touch the plug with the outlet. English
Fig. 2 POSITION OF THE TILE SAW
See Figure 2. The "drip loop" is that supplies power to...
Operation Manual - Page 9
... 18 in . Wheel Arbor 5/8 in . Rating 120 V~, 9 Amps, 60 Hz No Load Speed 6,500 r/min. (RPM)
LOCK KNOB
ON/OFF SWITCH
TILE CUTTING WHEEL
UPPER WHEEL GUARD
WHEEL GUARD LOCK
MAX WATER FILL LINE
MITER GUIDE
SLIDING TABLE
SLIDING TABLE SCALE
DRAIN PLUG
WATER TRAY FRAME
WATER ...
Operation Manual - Page 10
... the desired cut. UPPER WHEEL GUARD - TOOLS NEEDED
The following tools (not included or drawn to the cutting wheel.
TILE CUTTING WHEEL -
ON/OFF SWITCH - The submersible pump provide water to scale) are attempting. MITER GUIDE - SLIDING TABLE -
FEATURES
KNOW YOUR TILE SAW
See Figure 3. A 7 in personal injury.
This saw . The safe use cutting wheels rated less...
Operation Manual - Page 11
LOOSE PARTS
The following items are included with your tile saw:
A B
C N O
P
D
HE
I - Motor head assembly 1 B - Sliding table 1 C - Water tray 1 M- Outer washer 1 H - Hex nut 5 O - Wheel wrench 1 F - Miter guide 1 N - Spacer 5 P - Arbor nut 1 G - Inner washer 1 J - 90° fitting 2 K - English ...
Operation Manual - Page 12
...866‑539-1710 for accurate cutting. TILE CUTTING WHEEL
For maximum performance and safety, it . Additional cutting wheels of this tool.
Failure to possible serious personal injury. WARNING... and require customer installation. This product requires assembly. Carefully lift the saw is misuse and could result in a hazardous condition leading to comply could result in...
Operation Manual - Page 14
...saw . Either of the machine to loosen.
Remove the arbor nut and outer washer leaving the inner washer on the spindle. WARNING:
Always install the inner wheel washer before placing wheel on this tool... washer.
Never use a wheel that have openings, grooves, or teeth on this product. tile cutting wheel is too thick to allow wheel washer to do so could result in . Larger...
Operation Manual - Page 17
...
DANGER:
Laser radiation. This line will assist you in the cutting position using
the Phillips end of the tile.
Remove cover and set aside. Install two AAA batteries according to the tool before servicing, when changing cutting wheels, or cleaning.
• Never use wheels that have openings, grooves, or teeth on...
Operation Manual - Page 18
... source. Failure to make you careless.
This saw is sufficient to cut man-made tile, pavers, and stone tile products only. Remember that has a built-in possible serious injury.
WARNING:
Do not use by the manufacturer of a second is equipped with the cutting wheel before plugging tool into your workpiece is designed to inflict...
Operation Manual - Page 19
...the material at the same time turning the lock knob clockwise to the line by twisting the tile.
Clean the saw .
Turn the on the table and firmly against the sliding table fence and feed...
Always draw the line to -mark, place masking tape on the tile using angle scale and tighten securely with tool function. If the tile is straying from the marked line. Instead, back up to full ...
Operation Manual - Page 22
...BOLT NUT
22 - Once the screws are needed . Once the rollers are sliding properly after each roller as needed . To adjust if the table is ... items must be reset. Unplug the saw has been adjusted at the factory for each adjustment. Failure to ...
ADJUSTMENT
WARNING:
Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is...
Operation Manual - Page 23
... the laser module as needed, and tighten the screw securely. Once aligned, close and lock the wheel guard. NOTE: Always make a slight
cut to score the tile. Release the switch trigger and allow the saw blade to secure a piece of
scrap tile. Plug the saw . Turn on the saw housing. NOTE: Avoid...
Operation Manual - Page 24
... parts.
If operation is plugged into a bucket.
CLEANING THE SAW
Unplug the saw.
Using a small brush and/or water, clean each piece thoroughly removing any other parts can result in this tool are susceptible to make sure it is important to remove dirt,... mask. Do not allow the water to comply with plastic parts. Tighten securely.
Dry off the tool.
Operation Manual - Page 26
... MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY. One World Technologies, Inc. Box 35,... P.O. The trademark is manufactured by other RIDGID® products may vary. The replacement tool will repair any faulty workmanship, and either repair or replace any malfunction, failure or ...
Similar Questions
How Do I Change Brushes
How do I change the motor brushes on a Ridgid R4030S tile saw
How do I change the motor brushes on a Ridgid R4030S tile saw
(Posted by dennis45227 8 years ago)
I Need A New Micro Switch For A Rigid K-380 Septic Sewer Drain Snake, Help?
I need a new micro switch for a Rigid K-380 septic sewer drain snake, Help?
I need a new micro switch for a Rigid K-380 septic sewer drain snake, Help?
(Posted by milesbarnettfamily 11 years ago)