Sanyo HECSR1000K Support Question
Sanyo HECSR1000K Support Question
Find answers below for this question about Sanyo HECSR1000K - Stiffness Sensor - Multi Roller Massage Chair.Need a Sanyo HECSR1000K manual? We have 3 online manuals for this item!
Question posted by abrinkley1 on December 17th, 2011
How Do I Stop Rattles
My chair has gotten a lil noisier over the years. How do I tighten things inside so it doesn't rattle?
Current Answers
Related Sanyo HECSR1000K Manual Pages
Service Manual - Page 1
...time
30 minutes
Personal sensor course
Recovery / ...Massage sphere vertical reach
Approx. 635mm (straight line)
Reclining angle
Back: approx. 120-170 degrees, Leg: approx. 0-100 degrees
Leg massage
Rotating roller (Manual course: approx. 15 min., Automatic course: approx. 12 min.)
Roller rotation
Higher speed: 100 times/min., Lower speed: 70 times/min.
SERVICE MANUAL Massage chair...
Service Manual - Page 2
... IC IC-201)
Rotation detection of tapping motor (Hall IC IC-301)
Massaging pulse detection Massaging home position detection
Tapping pulse detection
SW for entering signals for instructing actions and LED for displaying the status
Remote control operation and display
Stiffness sensor section
Detection of perspiration rate by electric resistance
Detection of number of...
Service Manual - Page 3
... board CN604 (Control)
CN601
CN603 CN602 CNA601
CN11
CN951
Printed board (Sensor B)
Sensor B
12 15
CNA702 CNA701
Printed board (Indication)
Motor
CN5
Switch Switch
CN12
Reclining Motor(Back Rest)
Motor (Leg Roller)
CN2
CN1
CN9 CN10
CN6 CN8 CN13
Motor (Elevation) Condenser (16 F)
Motor Switch Switch Reclining Motor(Leg Rest)
CN404
CN402
CN403...
Service Manual - Page 4
... (Leg rest) Switch(UP) Switch(DOW)
Printed board (Pulse)
Printed board (Main)
Reactor
Motor (Tapping)
Reactor
Motor (Massaging) Reclining motor
(Back rest)
- 4 - Shape sensor
Printed board (Shape)
Printed board (UP/DOW pulse)
Motor (Elevation)
Condenser
Switch Fuse
Transfomer
Reactor Motor (Leg roller)
Printed board (Foot rest)
Reclining motor (Back rest)
HEC-DR21 (TAIWAN)
Service Manual - Page 5
Circuit Diagram
Printed board (Indication)
Printed board (Control)
- 5 -
HEC-DR21 (TAIWAN)
Printed board (Sensor A)
Sensor B Printed board (Sensor B)
Service Manual - Page 6
... temperature
If your body receives stimulus and feels "stiffness,"
Use rollers for neck/shoulder, back, and waste.
In the case of relax, perspiration rate tends to arm.
coil section
Even if body position is deviated during massage, the shoulder position is automatically corrected.
- 6 - Operation of Stiffness Detecting Sensor
HEC-DR21 (TAIWAN)
To the remote controller...
Service Manual - Page 7
... in four stages by detection massage, massage suited for stiffness feeling is judged in four stages and indicated in longer time. Based on and massage of sensor-automated massage
1. When "Recovery from fatigue course: (Steadily massages with special emphasis placed on and standard massaging operation takes place.
5.
Lightly press the sensor section B with rollers only).
Method and...
Service Manual - Page 8
... upward and downward by starting the elevation motor while running the tapping motor for tapping operation or the massage motor for massaging operation.
4, Leg massage motor
The leg motor rotation is transmitted to the outside roller through gear box. In addition, the rotating speed is changed over between normal/reverse.
Motor rotating speed is...
Service Manual - Page 9
...;˓˓
˓ ˔ ˓ The tapping motor doesn't move .
Tapping mode remains unchanged.
4. Insert the connector.
The connection confirmation of Printed board (pulse) CN301.
6. Massaging mode remains unchanged.
5. The connection confirmation of Printed board (Shape) CN501 and CN503. Check the Printed board (main) CN11 for the detection. Check the remote...
Service Manual - Page 10
...
ɾTrouble described left is displayed 3 seconds later after the power ON
ɾCheck limit switches motion.
ɾReplace the limit switch.
< Under normal condition >
Stop at the highest position(limit switch ON)
CN203 connector open ); ɹɹReplace the Motor (Elevation Each connector insertion.
ɾIf output, ɹɹReplace...
Service Manual - Page 11
... (pulse and temperature sensors).
ɾTrouble indicated after VARIOUS Power is turned "ON."
ɹ ɾSubstrate (main) failure
ɾReplace substrate (main).
- 11 - massage rotation detected. Problem Diagnosis Chart
Troubled portion
MANU LED
SPEED WIDTH LED LED
Troubled phenomenon ɹ
Check item
LEG ROLLER Leg roller motor overcurrent ɾMake sure roller cover, etc.
are...
Service Manual - Page 12
... a finger is placed between two electrodes,
LED "Put your finger on and operation of Each Sensor
Body contour sensor
Press in the massage mode go on the sensor" which is over about 17 or lower, LED "Ease" goes on for 1 second (Fig. 1)
Red's lighting-up
Red's lighting-up
Red's lighting-up Red's lighting-...
Service Manual - Page 14
...)
COVER
Photo.8
- 14 - Photo.7
COVER (BACK COVER)
COUTION LAVEL(REMOTE CONTROL)
SCREW
SCREW
Photo.5
Photo.7
4, Unscrew one CONDENSER ASS'Y set screw
SCREW
PRINTED BOAD ASS'Y (SENSOR A)
and remove CONDENSER ASS'Y. ASS'Y. Photo.8
Photo.6 3, Unscrew one PRINTED BOAD ASS'Y (REMOTE CONTORL) (7) Replacement of PRINTED BOAD ASS'Y (UP/DOW PULSE)
set screw and...
Service Manual - Page 16
... care to slip).
Photo.15
2, Detach BELT (MOMI). Photo.13 and detach HOLDER (MAGNET WIDTH) from shaft.
5, Detach PULLEY (MM) from massaging motor
Photo.15
shaft and unscrew three massaging motor set screws and 3, Unscrew one motor fixing screw.
Photo.16
8, Unscrew two pieces each of stay set screws on both sides...
Service Manual - Page 17
... moved to the position of Photo 19 by adjusting
2, Unscrew two PRINTED BOAD ASS'Y (RELAY) set
UP/DOWN by the use of main body with massage
PRINTED BOAD ASS'Y (RELAY).
Replacement Procedure
HEC-DR21 (TAIWAN)
(12) Replacement of PRINTED BOAD ASS'Y (RELAY)(PULSE) (14) How to remove backrest section
1, Disconnect three...
Service Manual - Page 18
...1, Disconnect three connectors connected to
PRINTED BOAD ASS'Y (SHAPE). SHAFT ASS'Y (SHAPE SENSOR)
SCREW
2, Since each LINEAR ACTUATOR ASS'Y. Photo.22
Holder
Magnet
3, Unscrew two ...HOLDER (ROLLING SHAFT UP), and remove the
massaging section upwards.
Replacement Procedure
HEC-DR21 (TAIWAN)
(16) Replacement of body contour sensor
1, Remove right arm helical spring.
Photo...
Service Manual - Page 19
... screws
and remove MOTOR GEAR BOX ASS'Y. Replacement Procedure
HEC-DR21 (TAIWAN)
(20) Replacement of leg roller motor
1, Open fasteners of MOTOR GEAR BOX ASS'Y
shaft. Photo.26
Fixing tape
Motor code
ROLLER STAY ASS'Y (LEFT)
ROLLER STAY ASS'Y (RIGHT) Photo.27
6, Pull out SPRING PIN of FOOT REST COVER A / B, and remove FOOT...
PARTS LIST - Page 1
... Rest)
CN3
CN4 CN14
Printed board(Main)
CN19 CN7
CN20
CN18
CN15
Transfomer
Fuse (250V 4A)
Switch
Motor Motor
Transfomer
CN501 CN503
Shape Sensor
CN502 Printed board (Shape)
CN201 Printed board (Relay)
Reactor
Limit Switch
CN203
Reactor
CN301 Printed board (Pulse)
Reactor(Leg Roller)
CN202
- 1 -
REFERENCE NO. PARTS LIST
Massage Lounger
FILE No.
PARTS LIST - Page 9
...411 169 9801 SCR S-TPG HEX+FLG 5X10
6
12 616 138 3709 SHAFT (ROLLER SHAFT)
1
13 616 138 3662 PULLEY (TM)
1
14 411 149 8008 ...SENSOR BOAD)
1
34 616 145 7097 CUSHION (UNIT FRAME)
1
35 616 139 8796 SWITCH HOLDER (MICRO SWITCH)
1
36 411 006 6307 SCR TPG PAN 3X20
1
37 616 142 6574 SWITCH ASSEMBLY (LIMIT SW) INCL/38 1
38 616 139 8789 MICRO SWITCH
1
Key No.
Parts No. Parts List (Massage...
PARTS LIST - Page 11
...001 0201 RING E 5
40 616 145 7110 SHAFT ASSEMBLY (SHAPE SENSOR)
41 411 028 8006 SCR S-TPG PAN 3X16
42 616 145...2
2
2
2
1
2
2
2
4
4
4
2
4
2
1
2
2
1
2
4
2
2
4
1
1
2
1
1
1
1
1
HEC-SR1000K (U.S.A.)
Description
Q'ty
- 11 -
Parts List (Massage unit)
NOTE: The parts marked with have special characteristics of safety, if replace the mark parts,use only SANYO...
Similar Questions
Replacement Seat-back Pad For The Sanyo Hec-dr6700k - Zero Gravity Massage Chair
I'm looking for a replacement seat-back pad. The part number is Are they available anywhere?
I'm looking for a replacement seat-back pad. The part number is Are they available anywhere?
(Posted by bdrinkwine 5 years ago)
Repair Store Nearest
Where can I find a repair store of Sanyo Massage chair HEC-DR6700K near 91748?
Where can I find a repair store of Sanyo Massage chair HEC-DR6700K near 91748?
(Posted by helenataka113 6 years ago)
How Do I Stop The Tv From Auto Shut Off? Also How Do I Power On Directly To Hdmi
little blue box appears in the lower left corner the it shuts off if no activity. i dont want auto s...
little blue box appears in the lower left corner the it shuts off if no activity. i dont want auto s...
(Posted by pughreco 11 years ago)
How To Stop Tv From Turning Off?
How to set the tv so it will stop turning off and on, the sleep mode is on off but it won't stay on ...
How to set the tv so it will stop turning off and on, the sleep mode is on off but it won't stay on ...
(Posted by milesladeidre 12 years ago)
Stop Microwave Beeps
Model EM-S2589S has 5 loud beeps I want to stop beeping
Model EM-S2589S has 5 loud beeps I want to stop beeping
(Posted by Caroleawall 12 years ago)