Snapper 150Z Support Question
Snapper 150Z Support Question
Find answers below for this question about Snapper 150Z.Need a Snapper 150Z manual? We have 2 online manuals for this item!
Question posted by eatonjack on August 21st, 2014
Ground Speed Adjustment
My snapper is slow on the right side ,and feels harder to push and pull on the joy stick. I checked manual and tried the adjustments it recommended but the ground speed is still to slow on right .is there another adjustment to increase ground speed ?
Current Answers
Answer #1: Posted by TommyKervz on August 21st, 2014 7:43 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Go on the link for instructions
http://www.manualslib.com/manual/156149/Snapper-150z-Series.html?page=30
http://www.manualslib.com/manual/156149/Snapper-150z-Series.html?page=30
Related Snapper 150Z Manual Pages
Operater's Manual - Page 8
...ground, speed too fast, inadequate braking, the type of
Select slow ground speed...try to stabilize the machine by putting your authorized dealer/retailer for another responsible adult.
2. See your c foot on the ground... area for
r recommendations of the towed equipment...children
stop . 6. t 8. The mower could
overturn the unit. Never
R .... will remain where you feel uneasy on it . Travel ...
Operater's Manual - Page 11
... is important! Decal - Pull the mower blade switch UP to
turn the mower blades OFF.
7102575
1 Sit in the seat.
3 5
2 Move the ground speed levers to ST ART/PARK positions (move the throttle/choke control to the F AST position for maximum engine speed
4
Always set the engine speed to F AST for
Although reading this manual and the safety...
Operater's Manual - Page 12
... never tamper with safety devices.
Operational SAFETY Checks
Test 1 - Engine SHOULD crank if:
• Mower blade switch is OFF, AND
• Ground speed control levers are in their START/ PARK ...complete stop within five seconds after the mower blade switch is in o disengage position, OR r • Operator moves the left and/or right ground speed control lever out of the safety interlock...
Operater's Manual - Page 13
... Lever
Choke
Engine
Parking Brake Lever -
Transmission Release Levers
RUN
OFF
START
Speed (Fast)
Engine Speed (Slow)
Mower Blade Switch
Ignition Switch
Figure 1. See DRIVING PRACTICE for starting the rider. for starting a cold engine. operating the ground speed levers.
Left Ground Speed Control Lever
Features and Controls
Right Ground Speed Control Lever
Ground Speed Levers -
Operater's Manual - Page 15
... care. WARNING
Gasoline is a rise of this rider and mower.
• Become familiar with a rear-mounted grass catcher.
o u Select slow ground speed before attempting to stop or park rider over injuring the operator...
If you do so now. To reduce fire hazard, keep the engine, rider and mower free of the controls and how to operate this rider. r Use caution when changing ...
Operater's Manual - Page 16
... adjustment is not R recommended.
rized Dealer for
this engine is EM (Engine Modifications). Return the ground speed control levers to START/ PARK positions to OFF. Move the engine speed control to SLOW ... Emergency Stopping
In the event of an emergency the engine can be stopped by pushing the mower blade switch down follow the procedure given in the Maintenance section).
• Fill ...
Operater's Manual - Page 17
.... The rider can now be pushed by running it to START to push or pull this unit to push or pull another vehicle to crank the engine.
fo tio Mowing t 1. c 2. Set the engine speed control to the RUN position.
3. e 7. Begin mowing. Do not use this unit. Turn the mower blades OFF, push the ground speed control levers out to their...
Operater's Manual - Page 18
... and damage to your lawn.
Slow down smoothly, slowly move both ground speed control levers evenly FORWARD...right, and then advance through a turn riders operate differently from neutral.
movements will
fo tio damage your lawn. To avoid turf damage, keep both ground speed...The BEST method of handling the ground speed control levers is
gradually push the levers forward with plenty ...
Operater's Manual - Page 19
... end of the rider will be! Right Turn fo tio Advanced Driving t c Executing an End-Of-Row Zero Turn o u Your zero turn rider's unique ability to turn in place, gradually move one ground speed control lever forward from neutral and one handle to stop and make your lawn by pivoting directly on the tire...
Operater's Manual - Page 20
...
Every 8 Hours or Daily
Clean debris from engine compartment
Check engine oil level
Every 25 Hours or Annually *
Every 25 Hours or Annually *
Check tire pressure
Clean engine air filter and pre-cleaner **
Check mower blade stopping time
Every 50 Hours or Annually *
Check rider and mower for loose hardware
Change engine oil
Every 50 Hours...
Operater's Manual - Page 21
...exposed engine cooling fins, and around the
R air filter assembly. Check Tire Pressure
Tire pressure should be checked periodically, and maintained at the levels shown in the air filter
... maintenance procedures.
Rider Maintenance Items
WARNING
Move the ground speed levers to START/PARK positions, engage the parking brake, turn the mower blades OFF, turn the ignition switch OFF, and...
Operater's Manual - Page 22
... after lubrication. Grease: • front wheel grease fittings • front wheel bushings • mower pivots • mower arbors
Use grease fittings when present. Mower Lubrication - 42" Deck
• brake linkage
• mower deck height adjustment linkage
• ground speed control linkage
Generally, all greases are compatible. Arbor Lubrication
RNeprod(3-Blade Model Shown, All...
Operater's Manual - Page 30
...
To increase the mower cutting height (raise the mower deck), press the top of the mower cutting height switch (A, Figure 31) To decrease mower cutting height (lower the mower deck), press the bottom of the mower deck..
Maintenance
Service & Adjustments
Ground Speed Control Lever
C
Adjustment
The control levers have three adjustments:
To Adjust Control Lever Height: Pull the levers in...
Operater's Manual - Page 31
...doubt about
Figure 32. r n Explosion hazard. Locate the brake rod (A, Figure 32) and adjustment nut (B).
3. Measure the parking brake spring. Its compressed
length, with skin and eyes. ...cables. A
WARNING
B
Corrosion hazard. Stop the unit, turn the ignition OFF, set the ground speed levers to START/PARK positions, set the parking brake lever to deliver the correct performance under...
Operater's Manual - Page 32
... 35.
Side to lock the
adjustment in place. Turn the engine off,
set the ground speed control levers to START/PARK, set the parking brake lever to ENGAGE, and wait for bent blades and replace if necessary. Maintenance
Mower Deck Leveling Adjustments
WARNING
A
Before inspecting or adjusting the mower, turn
the mower blades OFF, turn the ignition switch...
Operater's Manual - Page 33
... the tips of the mower deck. Loosen
e the jam nuts (C) and adjust the nuts up or down to mid position. Maintenance
A B C
Figure 36. Turn the engine
off, set the ground speed control levers to PARK, set
the parking brake lever to ENGAGE, and wait for bent blades and replace if necessary.
3. Check the tire pressures...
Operater's Manual - Page 40
... mower linkage is incorrectly adjusted.
Decrease Ground Speed. See Maintenance Section. PTO clutch out of adjustment. See Maintenance Section.
40 Parking brake is connected.
Torque as necessary. Check and replace as necessary.
Belt is oily or Clean or replace belt as per instructions.
Troubleshooting
Engine runs, Transmission release levers in PUSH...
Operater's Manual - Page 42
..., a typical walk-behind lawn mower is originally purchased.
If ...display information regarding your engine/equipment.
B&S recommends that you retain all receipts covering maintenance...Rights And Obligations
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are not exempted by the owner will be grounds for regular inspection in the owner's manual...
Parts Manual - Page 33
...Export) (used on 7800388) 1 DECAL, Tracking Adjustment ZT 7000 1 DECAL, RH Handle 1 DECAL...SNAPPER ZT 1 DECAL, 150Z 20HP SNAPPER ZT (CE/Export) 1 DECAL, 150Z 21HP SNAPPER ZT 1 DECAL, 150Z 26HP SNAPPER ZT 1 DECAL, Do Not Remove Foam Around Engine 1 DECAL, Instrument Panel ZTS 7500 1 DECAL, Instrument Panel (CE/Export) 1 DECAL, Instrument Panel ZTS 7600 (use on 7800620 & 7800621 models) 1 DECAL, Mower...
Parts Manual - Page 53
..., No Alarms 1 PLUG, Hole (Black Plastic) 1 SWITCH, PTO, Push/Pull Symbols 4 TIE, Self Locking, .184 Wide 7.31 Long 1 SWITCH, Push Button (NC) (Gray) (was 7102581) 2 CLIP, Cable, .390...WIRING ASSEMBLY, Jumper All Conditions Shutdown (CE/Export)
Footnotes:
HYDRO DRIVE ZTR 33", 42" & 50"
150Z SERIES
53
Manual No. 7006269 Wire 1 STRAP, Black Rubber, .19 Square 7.88 O.D. Electrical Group
Item
1 2 ...
Similar Questions
Replacement Battery For Snapper Re110
What battery size is needed for Snapper RE110 riding lawn mower?
What battery size is needed for Snapper RE110 riding lawn mower?
(Posted by yellgirl 1 year ago)
How Do I Tighten The Blade Belt On A Re 130 Re Series Snapper Riding Lawn Mower
(Posted by dobbsnick919 1 year ago)
Lawn Mower Wont Start
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
(Posted by cissy0 8 years ago)
Looking For Snapper Sp90 Law Mower Manual
Online manual for Snapper SP90 lawn mower
Online manual for Snapper SP90 lawn mower
(Posted by Ral1969 10 years ago)
How Do You Replace Driver Belt On Snapper 150z?
Bought in 2010 Snapper 150Z, Zero turn riding mower. How do I get to & replace the driver Belt?
Bought in 2010 Snapper 150Z, Zero turn riding mower. How do I get to & replace the driver Belt?
(Posted by Living4christ2010 10 years ago)