Home » Snapper » Lawn Mowers » Snapper RE100

Snapper RE100 Support Question

Find answers below for this question about Snapper RE100.
Need a Snapper RE100 manual? We have 1 online manual for this item!

Snapper Overview Questions Manuals Reviews Videos Research

Question posted by samnickel on July 29th, 2017

Will Not Pull Up Small Incline

snapper re100 will not pull up incline. I Removed rear cover (yoke) found clutch (rubber wheel) is lined up directly under engine pulley. Is the clutch supposed to b offset on one side of the pulley?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by waelsaidani1 on July 29th, 2017 1:18 PM

This answer was accepted by the poster of the original question.

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,797

1,100
points

The aluminum drive disc is adjustable on the crankshaft, and there is a specified measurement from the bottom of the engine. If it's too close to the engine, the drive system will slip

Related Snapper RE100 Manual Pages

Operater's Manual - Page 1

Manual No. 7104742 (Rev. '-') Description 7800784 2811524BV 7800785 2812524BVE 7800786 3014524BVE 7800787 3317524BVE RNeoptrfoodruction ! Operator's Manual REAR ENGINE RIDING MOWER SERIES 24 Model No.

Operater's Manual - Page 2

... many years of established lawns and is a trademark of the hazards and risks associated with the machine and how to the instructions in the Snapper brand. When operated and maintained according to avoid them. Date of Purchase Retailer Retailer's Phone Number r n Equipment fo tio Model Number t c Serial Number o u Engine RNeprod Model Type Code...

Operater's Manual - Page 3

...Engaging Mower Blade 13 Engaging Wheel Drive 13 Stopping Engine, Wheel Drive, Blade 14 Setting Park Brake 15 Cutting Height Adjustment 15 Reverse Lockout Mechanism 16 Maintenance 17 Maintenance Chart 17 r n General Maintenance 18 Storage 23 fo tio Engine Adjustments and Repairs 24 Mower Deck and Component Adjustments 24 Rear Engine Rider Drive Components 27 t c Mower Blade Replacement...

Operater's Manual - Page 4

... to stop or shift on the machine, engine and attachments. LOOK o u and SEE ... for another ride and be mowed and remove all objects such 5. The machine could ...these affect the handling and the stability of mower-related injuries. 1. Always begin forward motion ...3. washouts, culverts, fences and protruding objects. 4 www.snapper.com Failure to your foot on wet grass. machine....

Operater's Manual - Page 5

... is set. 8. Use only an approved fuel container. DO NOT remove fuel cap or add fuel with damaged. ning. DO NOT refuel the machine indoors. 5. e ers on feet rests or pedal(s). 10. STOP engine immediately after striking an obstruction. Exercise CAUTION when pulling loads. See manufacturer's instructions for emergencies. 6. DO NOT use accessories...

Operater's Manual - Page 6

...engine could ignite gas exiting engine. 14. On slopes, the weight of control. 8. Mower blades are in a well ventilated, unoccupied building. Keep engine... when making repairs. 6 www.snapper.com engine. Disconnect negative (black) cable from open ... needed. 5. spark plug could 4. Allow engine to ance. enclosure. Remove spark plug wire(s) from spark plug(s) Maintenance...

Operater's Manual - Page 12

..., with the transmission shift lever in a drive position. If the battery is pulled, the engine will turn over , and release R the clutch/brake pedal to start the engine with a smooth, even motion until the engine runs smooth. 12 www.snapper.com Engine (Manual Start) B IMPORTANT: When the key is turned to "ON", and the recoil Figure 8: Setting...

Operater's Manual - Page 14

... 1. RepA Figure 14: Engaging the clutch/brake pedal 14 www.snapper.com DO NOT leave the machine with the engine running. Stop the mower blade by releasing the blade pedals (A, Figure 15) or moving the blade lever (B) rearward to a complete stop in 3 seconds or less. Remove key. Operation ! Once blade is adjusted and functioning properly...

Operater's Manual - Page 16

...potentially dan- 2. BLADES must first stop the blade by a responsible adult. This riding mower has a Reverse Lockout Mechanism. Operation Reverse Lockout Mechanism Reverse Lockout Mechanism Override 1. Depress ... method but we encourage you must be selected unless you operate your local Snapper dealer for children, pets and hazards before backing machine. Move the blade lever...

Operater's Manual - Page 18

... tank before working on the rear bumper. (See statement below.) 3. the Engine Manual for sharpness, wear and damage. Engine Check Mower Blade and components are HOT. Refer to 40 ft. Dispose of used oil properly. 6. Carefully stand the Rear Engine Rider on machine. Fill the engine crankcase with a dual element air cleaner. Remove spark plug wire from spark...

Operater's Manual - Page 19

... of mower drive belt cover (B). 3. The following procedure requires the engine and blades to the deck. Clear area of a single belt from plug. The blade should skid. be completed before working on each side of cut position (middle p notch). The rear tires should stop rotating in 3 seconds or less after releasing the blade pedals. ! Remove...

Operater's Manual - Page 20

... General Purpose grease (NLGI No.2) with the engine off of the Reverse Lockout Mechanism with a engine cover, or the compartment will appear clean. 2. Refer to remove the air cleaner cover (B). Depress and hold the blade pedals. WARNING ! Front Wheel Bearings. Rear Axle Bearing. WARNING ! Change the air filter: • Pull up and rotate the air cleaner latch (A, Figure...

Operater's Manual - Page 21

... Lubricate all parts to prevent fuel spillage. Refer to the Section entitled "BATTERY REMOVAL". Follow the WARNING statement found on the rear Front Wheel Bearing - Carefully stand the Rear Engine Rider on this page. 2. Engine and components are HOT. Mower Deck Linkage - Carefully stand the Rear Engine Rider on this page. 2. Follow the WARNING statement found on the...

Operater's Manual - Page 24

... the following mower deck and component adjustments and repairs can not be adjusted. Reinstall the belt cover and tighten the bolts securely. STOP engine. Engage parking brake. Remove spark plug ... the dimension is greater than 3", rotate the nut counter-clockwise to an authorized Snapper dealer. If blade stop in achieving these adjustments and repairs, it should come to the ...

Operater's Manual - Page 26

..., it will be affected. Maintenance ! STOP blade. B A Mower Drive Belt Adjustment (For 28" & 30" Decks Only) 1. Refer to check Clutch/Brake Cable slack. Remove spark plug wire from spark plug and secure away from plug. Replace the pedal pad when adjustment is tightened securely. IMPORTANT: The SNAPPER Rear Engine Rider Models with the blade lever "ON...

Operater's Manual - Page 28

.... 28 www.snapper.com DO NOT sharpen beyond exist- If necessary, cor- If the blade is in the filler neck. • Empty the fuel tank before working Figure 42: Removing the mower blade B A Figure 43: Sharpening the mower blade IMPORTANT around cutting blades. ing cutting edge (A). 6. Maintenance ! lbs. Carefully stand the Rear Engine Rider on machine...

Operater's Manual - Page 29

... BELT COVER REMOVAL". 2. Stop filling the tank when fuel collects in the section, "CHECK MOWER DRIVE BELT". DO NOT attempt any adjustments, maintenance, service or repairs with your hand and work the belt between the drive disc and the rubber driven disc. 6. STOP blade. Adjust the belt guide to allow all parts to the engine pulley...

Operater's Manual - Page 30

...while it is installed on the battery with the removed hardware. ! Retain the mounting hardware. 5. Battery Battery Removal B 1. Connect the black negative (-) cable (C) to prevent corrosion. 5. Stop engine. Disconnect the BLACK (Negative) cable (C, Figure 49) from the ratchet fasteners (B) and remove the A cover. Carefully pull each side of grease over the positive terminal...

Operater's Manual - Page 32

...stale fuel in the OFF position. 5. Service mower blade(s). 2. Ignition is weak or dead. 10. Electric Starter 3. Connect starter cable. Service spark plug. 4. Loose or missing air lift (if equipped). 3. Replace pulley. 32 www.snapper.com Troubleshooting PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not 1. Engine needs choking. Faulty parking brake, blade or ignition...

Operater's Manual - Page 36

...snapper.com out these attachments. Due to -engine...(temperature, humidity, alti- REAR ENGINE RIDING MOWER SERIES 24 Product Specifications 2811524BV...engine. This differ- Torque values are placed, the gas engine may substitute an engine of higher rated power for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine...