Snapper RE130 Support Question
Snapper RE130 Support Question
Find answers below for this question about Snapper RE130.Need a Snapper RE130 manual? We have 1 online manual for this item!
Question posted by dickcee on March 28th, 2015
Grease Fittings
Are there any grease fittings for the RE130 front axle group?
Current Answers
Answer #1: Posted by TechSupport101 on March 28th, 2015 10:32 PM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,295
Member since:
May 24th, 2013 Points: 12,171,295
Page 20 of the manual says:
Lubrication - Grease Fittings
The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrica-tion. Apply General Purpose grease (NLGI No.2) with agrease gun.
1. Front Wheel Bearings. Refer to the section entitled"FRONT WHEEL BEARINGS - LUBRICATION".
2. Rear Axle Bearing. Refer to the section entitled "REARAXLE BEARING - LUBRICATION".
3. Mower Blade Spindle. Refer to the section entitled"MOWER BLADE SPINDLE - LUBRICATION".
4. Shift Lever. Refer to the section entitled "SHIFT LEVER -LUBRICATION"
Related Snapper RE130 Manual Pages
Operater's Manual - Page 1
Operator's Manual
REAR ENGINE RIDING MOWER SERIES 24
Model No.
Manual No. 7104742 (Rev. '-') Description 7800784 2811524BV 7800785 2812524BVE 7800786 3014524BVE 7800787 3317524BVE
RNeoptrfoodruction !
Operater's Manual - Page 2
... Engine RNeprod Model Type Code
SNAPPER is important that you aware of Briggs & Stratton Power Products Group, LLC Milwaukee, WI, USA. It is a trademark of the hazards and risks associated with the... to make you placed your Snapper product will provide many years of established lawns and is not intended for future reference. Save these instructions thoroughly before attempting...
Operater's Manual - Page 3
... of California to the State of Contents
Operator Safety 4
Features and Controls 9
Operation 10 Before Starting 10 Operator Seat Adjustment 10 Starting Engine 11 Engaging Mower Blade 13 Engaging Wheel Drive 13 Stopping Engine, Wheel Drive, Blade 14 Setting Park Brake 15 Cutting Height Adjustment 15 Reverse Lockout Mechanism 16
Maintenance...
Operater's Manual - Page 4
... the mowing
if an edge caves in this manual. Know the controls and the proper use of mower-related injuries.
1.
Use a slow speed and avoid sudden or sharp turns.
The owner of the...cause injury and damage!
DO NOT put your
machine which might impair vision, dexterity or judgment. mower safely enough to protect themselves and others to ride on the ground to try to the
6. ...
Operater's Manual - Page 5
... mowing over rough
into a trailer or truck. Immediately
of 7. STOP BLADES and ENGINE and make sure blades have
a dust mask, long pants and substantial footwear. mower to prevent
neath deck. r n Safe Handling of any reason.
9. Use only an approved fuel container. ly.
11. leaving operators position of Gasoline
To avoid personal...
Operater's Manual - Page 6
... allow extra distance to cool before
3. DO NOT store machine or fuel container inside where
10. Mower blades are in an
prevent controls from open flame, spark or pilot light such as
fo tio needed...may cause cause injury. Store fuel container out of the reach of grass, leaves or excess grease to spark plug hole; Tow only with a machine that
RNeoptroduc all bolts, nuts and ...
Operater's Manual - Page 7
...
• Keep hands and feet away from deck. A spark arrestor may create sparks that can start fires around
dry vegetation. WARNING
• Do not operate mower unless discharge
chute or entire grass catcher is in its proper
place.
7101110
RNeoptrfoodruction Danger Thrown Objects - 7101110
Fire Hazard.
Operater's Manual - Page 13
...
! A Figure 11: Engaging the clutch/brake pedal
Not fodruction B pro Figure 10: Engaging the mower blade Re Wheel Drive
A
1. Release the clutch/brake pedal to lift the grass while cutting smoothly and ...evenly.
13 This combination will allow the mower blades to begin forward motion.
5.
With the engine running , adjust the engine speed ...
Operater's Manual - Page 14
...with the engine running. Remove key. Engine, Wheel Drive, Blade
Engine
1.
Stop the mower blade by releasing the blade pedals (A, Figure 15) or moving the blade lever (B) ...Stop the engine by pushing the
o clutch/brake pedal (A, Figure 14) all the way down to the "OFF" position. Mower Blade
1.
STOP engine. B
A
r n A ot fo ctio Figure 13: Turning key to the "OFF" position.
...
Operater's Manual - Page 16
...BLADES, LOOK AND SEE
function.
This feature should o never be selected unless you operate your mower near roadways or use the Reverse Lockout Mechanism
then shift to avoid danger.
! DANGER
!
Release... shifted into reverse you to adjust to this new
fo tio system. This riding mower has a Reverse Lockout Mechanism. r n We realize that require quicker shifting to its...
Operater's Manual - Page 17
... 5 Hours
Check safety interlock system
Change engine oil
Clean debris off tractor and mower deck
Every 8 Hours or Daily
Clean debris from engine compartment
Check engine oil ...
Check tire pressure
Clean engine air filter and pre-cleaner **
Check mower blade stopping time
Every 50 Hours or Annually *
Check tractor/mower for loose hardware
Change engine oil
Every 50 Hours or Annually *
...
Operater's Manual - Page 18
...straightness.
Place a 2 quart minimum capacity container under the front wheels to the section entitled "MOWER BLADE REPLACEMENT" for inspection and addition of any new devices, which might upgrade the safety ... with the engine running. Check the torque of used oil properly.
6. entitled "ADJUSTING MOWER BLADE". DO NOT use a cutting blade that may have spilled.
pro A Re Figure...
Operater's Manual - Page 19
...: The blade drive belt on each side of
Figure 22: Measuring the belt spacing
the mower deck. DO NOT operate machine until
blade brake has been adjusted and functioning properly. SNAPPER ... components are not functioning properly, brake adjustment must be completed before working on the left side of mower drive belt cover (B). 3. Inspect for tion A t c B
No odu Figure 21: Removing ...
Operater's Manual - Page 20
.... tion.
WARNING
!
sealed to the engine manual for inspection. Rear Axle Bearing. Mower Blade Spindle. Refer to remove the air cleaner cover (B).
LUBRICATION".
20...into reverse. LUBRICATION".
4.
The operator rises off of the Reverse Lockout Mechanism with grease fittings and require periodic lubrica-
o DO NOT operate machine if Reverse Lockout Mechanism is...
Operater's Manual - Page 21
... before working on its
rear bumper. A
Figure 26: Shift lever grease fitting 21 Lubrication
Lubricate all grass clippings fo tio and debris.
Clean Mower Deck
Figure 24: Mower blade spindle grease fitting
1. Clean the underside of the mower deck, removing all
accumulation of the deck, removing all mower deck linkage pivot points with
N d three shots of motor oil...
Operater's Manual - Page 22
Engine
and components are visible, replace with a new plug.
4. Fuel Filler Cap
must be on the left rear axle
A
bearing requires three shots of general purpose grease
from plug. Rear Axle Bearing - A B
Notrfoodruction Figure 27: Rear axle grease fitting p Differential / Chain Case - Replace the fill/level plug if
Figure 28: Differential lubricant check
3. If signs of the...
Operater's Manual - Page 23
... the hose clamps (B, Figure 30) from the filter. Install a new fuel filter.
Refer to remain clean during storage. 5.
STOP blade. All bushings and pivot areas. 2. Mower deck linkage and pivot areas.
t c 6. Drain the fuel from the fuel tank. 2. Engine and components are HOT. Clutch yoke. 6. This allows the carburetor and fuel...
Operater's Manual - Page 24
... the dimension is disengaged it is adjusted and
functioning properly. Once blade is less than 3", rotate
the nut counter-clockwise to a stop , N d perform the following mower deck and component adjustments and repairs can be adjusted. DO NOT attempt any time the blades are HOT. Remove key. Avoid serious burns, allow all...
Operater's Manual - Page 30
... (C) to charge the battery while it is installed on the battery with the removed hardware.
4.
Retain the mounting hardware.
! WARNING
! Carefully pull each side of grease over the positive terminal.
6.
WARNING
! Stop engine. Engine
and components are HOT. Avoid serious burns, allow all
parts to the
positive terminal (+) on machine. Slide...
Operater's Manual - Page 34
...of merchantability and fitness for a particular purpose, are excluded to the conditions stated below. OWNER WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton Power Products Group, LLC will ...devices, your unit is not covered by purchaser. Warranty
BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. Briggs & Stratton Corporation will o be appropriate. Transportation charges on the date...
Similar Questions
Replacement Battery For Snapper Re110
What battery size is needed for Snapper RE110 riding lawn mower?
What battery size is needed for Snapper RE110 riding lawn mower?
(Posted by yellgirl 1 year ago)
How Do I Tighten The Blade Belt On A Re 130 Re Series Snapper Riding Lawn Mower
(Posted by dobbsnick919 1 year ago)
How Do I Adjust The Belt Tension On The New Frame Style Re130?
(Posted by dcstallingsphotography 3 years ago)
Steering Stiff
Our mower sat up for awhile now steering is too tight to mow. How to fix?
Our mower sat up for awhile now steering is too tight to mow. How to fix?
(Posted by shirldi48 3 years ago)
Lawn Mower Wont Start
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
I have sp80 ran over small stump mower stopped, started again and ran until I stopped it to empty ba...
(Posted by cissy0 8 years ago)