Stihl MS 201 T C-M Support Question
Stihl MS 201 T C-M Support Question
Find answers below for this question about Stihl MS 201 T C-M.Need a Stihl MS 201 T C-M manual? We have 1 online manual for this item!
Question posted by cristjt14 on February 16th, 2017
My 201 Tc Loading Up?
idles well then when I hit the throttle it dies or bogs down. Is anyone rise having this problem. Vaccum test was good no leaks but was only getting 95 psi on compression test so checked cylinder piston and rings cylinder piston looked good so put new rings in it same compression with new rings is this normal? Runs great other then coming off idle seems like it's loading up.
Current Answers
Answer #1: Posted by Odin on February 16th, 2017 8:14 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
See https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Chainsaw/119---/Chainsaw-starts-then-stalls,
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Stihl MS 201 T C-M Manual Pages
Instruction Manual - Page 1
STIHL MS 201 T
{
Instruction Manual Notice d'emploi
Instruction Manual - Page 3
...8221-A. VA3.B12. 0000004906_004_GB Guide to Symbols STIHL Limited Emission Control Warranty Statement CSA Standard
{
MS 201 T
36 Dear Customer,
38 Thank you have any queries
concerning your dealer or our sales...
25
Replacing the Starter Rope and
Rewind Spring
27
Storing the Machine
29
Checking and Replacing the Chain
Sprocket
29
Maintaining and Sharpening the
Saw Chain
30
...
Instruction Manual - Page 4
... pump
Tank for felling trees or cutting firewood. chain oil flow adjustment Tension saw (cut injuries due to uncontrolled reactive forces of fall protection equipment
2
MS 201 T
Operators must be specially trained for such operations.
Therefore, some changes, modifications and improvements may be covered in this Instruction Manual.
in special cutting and...
Instruction Manual - Page 5
...who have any condition that could get caught on branches or brush or ...sturdy but allow complete freedom of any questions in good physical condition and mental health. Do not wear... in use, shut it off the work , check with cut wood or wooden objects.
They are ...surgery saw and are under the influence of movement.
MS 201 T
3 Always observe country-specific safety regulations, ...
Instruction Manual - Page 6
...to idle position.
- fuel may cause arcing that saw short distances. throttle trigger must move easily to appropriate sections in good condition...serious of throttle trigger and throttle trigger lockout - Before Starting
Check that could ignite combustible fumes and cause a fire.
4
MS 201 T ..., non-slip soles and steel toes. If fuel gets on your body - Refer to 0 or STOP
-...
Instruction Manual - Page 7
...checked, fueled, started and warmed up to 0 or STOP. Make sure you always have good balance and secure footing. To ensure safe control, wrap your body are left-handed. Make sure you have good...for safe control of the throttle trigger (flywheel effect). ...one person only. never cut and -
MS 201 T
5 for a short period after you.... tie it to the ring and attach it is particularly...
Instruction Manual - Page 8
... the safety devices are very high, wear a suitable respirator.
Check and correct the idle speed setting at the cutting site must not run the engine indoors or in particular for leaks and make proper adjustments or repairs. Check condition and proper mounting.
- Mufflers with the throttle trigger released. If dust levels are working in slippery...
Instruction Manual - Page 9
when another solid object, e.g. when the chain at full throttle.
-
To reduce the risk of a second - Work cautiously and avoid situations ... on "Chain Brake" in certain situations -
always hold the spiked bumper securely against the tree or limb.
001BA037 KN
MS 201 T
7 Never cut to chapter on the bottom of this manual.
The reaction of injury in this device refer to ...
Instruction Manual - Page 10
...with the chain running.
Always pull the saw at the compression side (A). Work calmly and carefully - Ensure you have better... a ladder or on the top of the bar is good.
The reaction of the chain drives the saw will otherwise...underbuck) - motor vehicles). MS 201 T To avoid pushback:
-
the saw straight back toward the operator. When working with the throttle trigger in the wood, ...
Instruction Manual - Page 11
...tingling sensation in good condition, secure ...Check the fuel filler cap for the length of genuine STIHL replacement parts.
MS 201...-induced circulation problems in the ...Exception: Carburetor and idle speed adjustments. Carefully...be given for leaks at regular intervals...get pinched and cause kickback and loss of accidents. Hand protection (wearing warm
gloves) -
If the saw gets...
Instruction Manual - Page 12
... guide bars, saw chains and chain sprockets. Store fuel and chain lubricant in good time. health risk. To reduce the risk of clutch drum periodically. Maintenance, ... of operation.
10
MS 201 T before rectifying problems.
Observe sharpening instructions - If non-matching components are used , STIHL may be properly sharpened, tensioned and well lubricated.
Check condition of injury, ...
Instruction Manual - Page 15
...Engines equipped with an ethanol content of the piston seizure and damage to time.
This could cause... in engine temperature. Ethanol can cause running problems and major damage in engines with a manually...increases the risk of up to avoid any moisture getting into the canister first, and then add gasoline...MS 201 T
13 Fuel
This engine is accompanied by more than 50%.
Instruction Manual - Page 20
...throttle trigger causes the master control lever to the
position for starting
- engine is for "summer operation" s
Risk of the Master Control lever
Stop 0 -
if the engine stalls during opening of the combustion chamber, if the engine was flooded
18
MS 201... to jump from around the cylinder and mixed with cold air. After ventilation of throttle after starting the warm engine ...
Instruction Manual - Page 23
...idle...load) for the first three tank fillings.
After finishing work . English
Chain cold
Tension is cold
N Restart the engine
When the fuel tank has run at operating temperature during work
N Slacken off the bar. see "Tensioning the Saw Chain". After a long period of full-throttle operation
After a long period of the bar - Check...for an extended period.
MS 201 T
21 The engine ...
Instruction Manual - Page 31
...preserve the chain sprocket. N Thoroughly clean the machine - pay special attention to test
Using two saw chains or earlier
-
if the wear marks (arrows) are ... the cylinder
0011BA037 KN
MS 201 T
29
N If you use of chain sprocket and clutch described in the following, a locking strip is dry - this helps prevent the carburetor diaphragms sticking together.
Checking and Replacing...
Instruction Manual - Page 32
... the cylinder fin
N Turn the clutch clockwise until the piston rests ... very little pushing.
N Clean the saw chain
N Check the saw chain for cracks and damaged rivets
N Replace...necessary. can lead to increased physical strain, increased vibration load, unsatisfactory cutting results and increased wear. rework accordingly
...MS 201 T especially depth gauges that are especially wear-resistant.
Instruction Manual - Page 37
English
before starting work at the end of operation
MS 201 T
35
If the machine is refilled weekly monthly yearly if faulty if damaged as required
Cooling air intake slits
clean
X
Cylinder fins
clean
X
X
Check idle adjustment - The specified intervals must not rotate
X
X
Carburetor
Setting the idle speed
X
adjust electrode gap
X
Spark plug
replace after 100 hours...
Instruction Manual - Page 38
...
12
9
6
10
13
7
8
14
19
20 21
17 18
#
15 16
23 22 24
25
1 Control Handle 2 Throttle Trigger Lockout 3 Master Control Lever 4 Throttle Trigger 5 Carburetor Adjusting Screws 6 Shutter (Summer and Winter
Operation) 7 Spark Plug Boot 8 Muffler (with Spark Arresting
Screen) 9 ...23 Carburetor Box Cover Twist Lock 24 Fuel Filler Cap 25 Ring for Rope # Serial Number
0012BA023 KN
36
MS 201 T
Instruction Manual - Page 39
...idle speed. (not illustrated)
Anti-Vibration System The anti-vibration system includes a number of anti-vibration elements designed to the operator's hands. (not illustrated)
MS 201...Chain")
Clutch Couples engine to stop switch position.
4 Throttle Trigger Controls the speed of cutters, tie straps and ...For closing the fuel tank.
25 Ring for Rope Pull-out ring for the left hand from operator....
Instruction Manual - Page 40
... capacity:
0.22 l
Weight
dry, without bar and chain MS 201 T: MS 201 TC:
Cutting Attachment
3.7 kg 3.8 kg
Picco Super 3 (63... been shown to ISO 7293:
1.8 kW (2.4 HP) at 9,500 rpm
Idle speed:
3,000 rpm
High speed setting
when performing
repairs (with integral fuel ... = 50 hours
Engine
Single cylinder two-stroke engine
Displacement:
35.2 cm3
Bore:
40 mm
Stroke:
28...
Similar Questions
Fuel For Ht-101
I have borrowed a used one to try out. Looks like a 4 cycle engine. Do you run straight gas in this?
I have borrowed a used one to try out. Looks like a 4 cycle engine. Do you run straight gas in this?
(Posted by drtomt 2 years ago)
Stihl Sr 90 Trimmer. Primer Bulb Is Not Getting Gas. Have Checked All Gas Lines
primer bulb does not get any gas. Have already checked the 2 gas lines and they seen unclogged. What...
primer bulb does not get any gas. Have already checked the 2 gas lines and they seen unclogged. What...
(Posted by adrianaaldrete 5 years ago)
I Have To Choke It To Start It It Revs High For About 10 Seconds Then Dies Out
I was told I have a float that is sticking and looking at the schematic I don't see a float PR they ...
I was told I have a float that is sticking and looking at the schematic I don't see a float PR they ...
(Posted by Koberhausllc 6 years ago)
Part No For Stihl Km90r On/of Switch
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
i require 1 new on/of switch for my stihl km90r want part no or where it can be purchased its orange...
(Posted by johnnash222 8 years ago)