Troy-Bilt Mustang 50 Support Question
Troy-Bilt Mustang 50 Support Question
Find answers below for this question about Troy-Bilt Mustang 50.Need a Troy-Bilt Mustang 50 manual? We have 2 online manuals for this item!
Current Answers
Answer #1: Posted by waelsaidani1 on August 14th, 2014 8:28 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,787
Member since:
May 12th, 2013 Points: 19,501,787
Instructions Step 1
Remove the spark plug ignition wire.
Step 2Remove the dip stick.
Step 3Using the Arnold Siphon Pump, place the orange tube into the dip stick hole on the engine, and the black tube into the oil pan.
Step 4Prime the pump by pumping the handle three to four times. Once the liquid begins to flow, it will flow without further pumping.
Step 5Remove the orange tube and add new oil as instructed in your operator's manual.
Step 6Replace the dip stick.
Step 7Replace the spark plug ignition wire.
Step 8Dispose of oil properly.
Related Troy-Bilt Mustang 50 Manual Pages
Operation Manual - Page 4
...the parking brake
2. Muffler and engine become hot and can result in this
dump cart, lawn roller, etc.) on it .
Do Not:
where the operator may speed up the slope...slopes unless necessary; Exercise extreme caution when changing direction on ramp(s) to improve stability. This machine should evaluate their ability
to operate the riding mower safely enough to stabilize the machine by ...
Operation Manual - Page 5
...years of a responsible adult other than from a hot muffler. loaded dump cart, lawn roller, etc.) on a truck or trailer bed with safe machine operation. To ...when approaching blind corners, doorways, shrubs, trees or other debris build-up oil or fuel spillage and remove any fuel soaked debris. They can suffer burns ... and change clothes immediately. j. If gasoline is hot or running engines.
Operation Manual - Page 6
...EPA), this manual. Also, visually inspect blade(s)
for gas, oil, etc. may include the following emission control systems: Engine ...compromise safety!" Failure to be maintained in this manual.
Mower blades are certified to the Consumer Products Safety Commission ...use extra caution when servicing them.
7. Do not change the engine governor settings or over-speed the engine...
Operation Manual - Page 11
...
Section 2 - Adjusting the Seat
To adjust the position of the seat pan. See Figure 3-7.
50" Deck Shown
Flange Lock Nuts
Clamp Knob
Push Nuts
Carriage Bolts
Seat Adjustment
Positions
Figure 3-5
3....Make sure the seat is locked into the seat, then tighten securely. Never operate the mower deck without the chute deflector installed and in the down position. Lower Deck Discharge Chute ...
Operation Manual - Page 14
... the ignition switch in the "START" position. The maintenance interval lasts for two hours (from 50-52, 100-102, 150-152, etc.). If this indicator if the engine will alternately flash,...started .
If necessary, move the PTO switch to the right of maintenance intervals for changing the engine oil.
When key is turned to have the tractor and engine inspected. If the indicator comes...
Operation Manual - Page 15
...PTO switch must not be used where exhaust emissions are not approved.
• Check the engine oil level.
• Clean the air cleaner element if necessary.
• Check the tire inflation ...disengaged.
• The safety interlock system will shut off the PTO and the mower blades will change the balance of the operator. Never operate on traction surfaces that are approved fuels...
Operation Manual - Page 20
... NOTE: Do not engage the mower deck when lowered in the neutral/parking brake engaged position. Premature wear and possible failure of the turf, if possible, change the direction that can be placed ...
2. Mow across slopes, never up and down or stop and remove the key from your lawn ''browned'' by the rotating blades. When approaching the other objects that the strips are made ...
Operation Manual - Page 22
...castor wheel axles with a quality lubricating oil. Using the Deck Wash System
WARNING! Do not use
P
Every 10 Hours
P P
Every 25 Hours
P P
Every 50 Hours
Every 100 Hours
Prior to the... Engine Manual for all tractor models and the tractor depicted may vary by model. Move the tractor to an area within reach of the hose where the dispersal of the mower...
Operation Manual - Page 23
... or petroleum jelly, to lock it inspected and serviced by reversing steps a & b after every 50 hours of ignition (cigarettes, matches, lighters) away from doing so.
1. However, even a "... Batteries contain sulfuric acid and may not fully recharge the battery. A discharged battery can be changed. Keep the exterior of corrosion.
• Avoid tipping. Refer to service. Section 6 -...
Operation Manual - Page 26
...in shortened life and reduce serviceability.
5. Maintenance & Adjustments See Figure 6-6.
Change the engine oil and filter following the instructions provided in a dry and protected location. Engines ...pressure.
3. Replace the spark plugs and the ignition leads.
4.
Store the riding mower in the Engine Manual.
Protect the metal surfaces.
Store in a cool, dry ...
Parts Manual - Page 2
Part No. TroyBilt Mustang 50" RZT
Frame
1
5
3 5
8 10
7 3
5
2
6
9 4
Ref. No.
1 603-04303D 2 703-05829 3 710-0520 4 710-3005 5 712-04065 6 732-0626 7 736-0300 8 738-04058 9 738-04162A 10 756-...
Parts Manual - Page 3
TroyBilt Mustang 50" RZT
Front Axle
4
9
6 10
11
9
13
9 12
1
15 14
5
4 2
7 13
3
9
8 15
Ref. No. Description
1 603-04370 Bracket, Castor Wheel
2 603-04385A Axle, Front Pivot
3 634-...
Parts Manual - Page 4
TroyBilt Mustang 50" RZT
18 9
Electrical
4 14
10 4
3 9
18
2 6
15 12
11 6
1 16
13 8 7
5
9 17
Section of Main Wire Harness (Reference Only)
Parts Manual - Page 5
...-1707D 15 726-0278 16 726-0279 17 726-0470 18 738-04237A † 725-04621
Description
Screw, Hex Wash. Part No. Pole - Hd. TroyBilt Mustang 50" RZT
Electrical
Ref.
Parts Manual - Page 7
... Wash. Tapp, 5/16-18 x .625 Screw, Hex Wash. Hd. Tapp. , 1/4-20 x 1.5 Screw, Hex Wash. Hd. Hd. Tapp, 5/16-12 x .75 Screw, Hex Wash. Hd. TroyBilt Mustang 50" RZT
Operator's Platform
Ref. Part No. Tapp., 1/4-20 x .5 Screw, Hex Wash. Hd Tapp, 5/16-18 x .75 Pin, Clevis, .5 x .78 Nut, Hex Jam, 1/4-20 GR2 Nut...
Parts Manual - Page 9
..., .5 x .434 Bearing, Hex Flange Bearing, Flange, .625 x .938 x .344 Rod, Lapbar Control Rod, Deck Front Hanger Rod, Deck Lift Handle Hub, Control Part No. TroyBilt Mustang 50" RZT
Operator's Controls
Ref.
Parts Manual - Page 11
... Housing, Deck
777S32598
Graphic, Danger
777S30503
Graphic, Danger
777I22282
Graphic, Instruction
777D11833 Graphic, 50"
2 618-04125A Spindle Assembly
3 631-04070A Chute Assembly, Discharge
777S30284
Graphic, Danger
..., Hex Cap, 5/16-18 x 1.25 GR5
10 710-0599 Screw, Hex Wash. TroyBilt Mustang 50" RZT
11
Mower Deck
Ref. Tapp, 5/16-12 x .75
12 710-1260A Screw, Hex Wash. Tapp,...
Parts Manual - Page 12
TroyBilt Mustang 50" RZT
12
Engine Connections
23
20
7
9 17
32
24 13
22
10
27
31
4
16
30
11
28
8 1
26 12 25
2
18 6
5 12
3
18 29 6
33
6
14
21
15
19
Parts Manual - Page 13
...Gal.
28 751-10253 Pipe, Exhaust LH
29 751-10254 Pipe, Exhaust RH
30 751-10291 Hose, Oil Drain Extension
31 751-10349-13 Hose, Fuel Line
32 751-3124B Cap, Fuel
33 756-0978B Pulley...
8 710-3008
Screw, Hex Cap, 5/16-18 x .75 GR5
9 710-3217
Screw, Truss Hd. Part No. Hd. TroyBilt Mustang 50" RZT
13
Engine Connections
Ref. Hd. Tapp #12-16 x .5
5 710-0599
Screw, Hex Wash. Tapp 1/4-20 x .5
...
Parts Manual - Page 14
... Cap, 5/16-18 x 2.25 GR5
5 710-0176 Screw, Hex Cap, 5/16-18 x 2.75 GR5
7 710-3119 Screw, Hex Cap Lock, 3/8-16 x .75 GR5
Ref. TroyBilt Mustang 50" RZT
14
Hydro Transmissions & Rear Wheels
8
7 12
10 4
1
8
8
16
2
14
13
4
5 15 6
31
9 11 56
10 7
12
Ref. Part No.
Similar Questions
Need New Motor Engine For Troy Bitl Riding Lawn Mower 15.5
(Posted by janicesutton60 2 years ago)
Mowerrunning Then Shuts Off Says Low Oil Pressure. Just Changed Oil
(Posted by alliegoodman94 2 years ago)
My Mustang Rzt 50 Was Running Fine I Got Off For A Minute ,got Back On And It Wo
I was using my mustang rzt 50 it was running fine. I got off of it for a minute got ck on and it won...
I was using my mustang rzt 50 it was running fine. I got off of it for a minute got ck on and it won...
(Posted by mob816 8 years ago)
Lawn Mower
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
(Posted by sgilbert491974 9 years ago)