Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by Joepupi on December 5th, 2020
Not Starting
I changed oil and replaced spark plug but it will not start I also forgot to drain out old fuel so I am thinking that is the issue what should I do
Current Answers
Answer #1: Posted by Odin on December 5th, 2020 1:27 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
See the first-listed Problem at https://www.manualslib.com/manual/183816/Troy-Bilt-Storm-2410.html?page=25.
If you require further advice, you'll have to consult the company; use the contact information at https://www.contacthelp.com/troy-bilt/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 1
... IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Two-Stage Snow Thrower - Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Operation Manual - Page 2
... 16 Maintenance & Adjustment 17
Service 20 Troubleshooting 24 Replacement Parts 25 Attachments 26 Warranty Back Cover
Record Product Information...Manual may not be applicable to all engine-related issues with regards to performance, power-rating, specifications,...you for more information. We reserve the right to change product specifications, designs and equipment without notice and ...
Operation Manual - Page 3
...can result in this machine.
Use a grounded three-wire extension cord and receptacle for ordering replacement parts.
2. Read and follow all instructions in serious injury or death. HEED ITS WARNING!...the machine and disengage them quickly.
3. California Proposition 65
WARNING! As with electric start engines.
4. Read, understand, and follow all instructions on the machine and be...
Operation Manual - Page 4
... the spark plug wire ...Wash your nearest servicing dealer.
4. Exercise caution when changing direction and while
d. hot or running . Allow...control levers and stop before starting engine, pull cord slowly until fueling is felt, then pull rapidly...fuel tank. Do not overload machine capacity by attempting to unclog the discharge opening at least two minutes before you can let go. Replace...
Operation Manual - Page 5
...to comply with spark plug removed.
14....fuel line, tank, cap, and fittings frequently for gas, oil...Replace if necessary.
13. Snow thrower shave plates and skid shoes are certified to keep the machine in safe working properly and not worn excessively. Notice Regarding Emissions
Engines which do so can lead to prevent unintended starting.
3. To clear the chute:
1. Do not change...
Operation Manual - Page 7
...Snow Thrower Operator's
Manual • One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410)
• One Product Registration Card
• One Chute Control Rod...certain the cables are seated properly in the Forward-6 position. 2. Figure 3-2
Chute Assembly (Model 2410)
1.
See Fig. 3-1. Assembly & Set-Up
3
Contents of the handle. Secure the ...
Operation Manual - Page 8
... chute assembly to Chute Bracket Adjustment on Page 19.
8
Section 3-
Chute Control Head
Chute Support Bracket
Chute
Chute Base
Figure 3-4
Figure 3-6
Chute Directional Control (Model 2410)
2. 2.
Operation Manual - Page 11
... entire bottom surface of the chute assembly. 2. Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on the skid shoes.
3. Caution: It is also controlled by changing the angle of tire for shipping purposes. See Fig. 4-1. Insert Key into engine and start engine. Equal tire pressure should be maintained at the factory...
Operation Manual - Page 12
In a well-ventilated area, start the snow thrower engine. Position the bracket upward to provide more slack (or downward to the front of rotating, immediately return to Engine Operator's Manual.
3. ...
Operation Manual - Page 13
..., the augers rotate and draw snow into the auger housing is discharged out the chute assembly. Position one (1) is the slowest and position six (6) is started.
13 See Set-Up & Assembly section. Skid shoe styles and appearance vary by model. Headlight (if so equipped)
The headlight is located on top of...
Operation Manual - Page 14
... drive. Squeeze the control grip against the handle to engage the augers and start snow throwing action.
Controls and Features Squeeze the control grip against the handle ...14
Section 4 -
To activate the heated grips, move the switch found on the right handle. To change the direction in which snow is thrown, rotate chute directional control.
2-Way Chute Directional Control (if so...
Operation Manual - Page 15
...directional control is located on the left side of the auger housing, reinsert the key and start the snow thrower's engine. Shut off engine and remain behind the snow thrower), engage the auger ...parts have stopped before unclogging. Stop the engine.
Section 4 - The left . • To change the angle/distance which snow is conveniently fastened to the rear of the clean-out tool to safely ...
Operation Manual - Page 16
... the right steering trigger control to do so will not turn, check to stop . Operation
5
Starting and Stopping the Engine
Refer to turn left. Squeeze the left handle.
warning! If the heated...the auger gearbox or other than OEM Part No. 738-04124A replacement shear pins. To Engage Augers
To engage the augers and start throwing snow, squeeze the auger control against the handle the ...
Operation Manual - Page 17
... the Engine Operator's Manual. Apply a light coating of fuel.
2.
NOTE: Augers not shown for information regarding tire ...oil. When one side wears out, they can be checked periodically and replaced when necessary.
Clean and coat the axles with 3-in -1 oil... 7-3.
4. Wipe off any oil on the auger housing.
3.
Standard Chute Directional Control (Model 2410)
Once a season, lubricate...
Operation Manual - Page 19
... Adjustment (Model 2410)
If the ... as instructed earlier in an unventilated area,
rustproof the machine using a light oil or silicone to coat the snow thrower. 5.
Figure 6-7
2. Run the engine until the hole... cotter pin through this section. 3. Maintenance & Adjustments
19 Do not attempt to pour fuel from the hole closest to the Engine Operator's Manual for 30 days or longer, follow...
Operation Manual - Page 20
...7-3.
1. Remove the key to pour fuel from the engine. See Fig. 7-4.
Figure 7-1 3. See Fig. 7-2. a. Remove the frame cover from the frame. Do not attempt to avoid unintended starting.
2. Remove the belt as a belt...auger belt off the engine pulley. Service
7
Belt Replacement
Auger Belt
To remove and replace your snow thrower's auger belt, proceed as follows:
4. Unhook ...
Operation Manual - Page 22
... so that it is out of fuel. Figure 7-8
22
Section 7 -
NOTE: Special tools are required and several components must be replaced. To inspect the friction wheel, proceed as instructed on page 2 for signs of wear or cracking and replace if necessary:
1.
Stop Bolt
Friction Wheel Removal (Models 2410, 2620 & 2840)
If the snow thrower...
Operation Manual - Page 24
... fails to start button, on models so equipped). 1. Choke not in auger.
3. Spark plug wire disconnected. 3. Fuel tank empty or stale fuel. 4. Key not in fuel system. 4....directed in the Operation
section. 5. Clean, adjust gap, or replace. 6. Move choke lever to spark plug. 3. Fill tank with fresh fuel. 4. Drain fuel tank. Refill with clean, fresh gasoline. 3. Contact an ...
Operation Manual - Page 25
...
931-2643
Chute Clean-out Tool
790-00120 790-00121 790-00118 790-00119
Shave Plate (Storm 2410) Shave Plate (Storm 2620) Shave Plate (Storm 2840) Shave Plate ((Storm 3090XP)
731-05632
Key
951-10292
Spark Plug
Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready).
Operation Manual - Page 26
... Snow Thrower Maintenance Kit
26 Model Number
Description
753-05762A OEM-390-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410. Attachments & Accessories
10
The following attachments and accessories are available for information regarding compatibility, price and availability (have your Troy-Bilt snow thrower. Phone (800...
Similar Questions
Snowblower Starving For Gas. Tank Is Full,so I Start And Let It Run, Then Died?
we drained a nd added new fuel and new spark plug. Start w full choke let it run. Turn down choke th...
we drained a nd added new fuel and new spark plug. Start w full choke let it run. Turn down choke th...
(Posted by LINNICI 2 years ago)
My Storm 2620 Isn't Getting Spark To The Plug.
Is it most likely the ignition coil?
Is it most likely the ignition coil?
(Posted by chameleoncline 3 years ago)
Troy Built Storm 2410
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
(Posted by brucepieper1 3 years ago)
Spark Plug Change
I'm trying to check the spark plug on my Troy-Bilt CSV 070. I cannot find a socket that will fit. Wh...
I'm trying to check the spark plug on my Troy-Bilt CSV 070. I cannot find a socket that will fit. Wh...
(Posted by davidcary 7 years ago)