Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by Gatlintom on December 27th, 2022
Tire Is Flat
Tire is flat, struggling to get it off sxe
Current Answers
Answer #1: Posted by Odin on December 27th, 2022 11:51 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,630
Member since:
April 10th, 2010 Points: 41,236,630
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 1
... IN PERSONAL INJURY. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Two-Stage Snow Thrower -
Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Operation Manual - Page 4
... lock-open flame, spark or pilot light
14. Do not use care
j. Doing so makes the machine unsafe and may cause personal injury. wheel weights, tire chains, cabs etc.).
20.
Engine exhaust contains carbon monoxide, an odorless and deadly gas.
6. c.
snow at least 5 minutes before
Operation
1.
Never store the machine or...
Operation Manual - Page 7
Figure 3-2
Chute Assembly (Model 2410)
1. See Fig. 3-2. 3. Figure 3-3
7
Observe the lower rear area of the handle.
Secure the handle by ... Operator's
Manual • One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410)
• One Product Registration Card
• One Chute Control Rod (Models 2620, 2840 and 3090XP)
Assembly
Handle
1.
Operation Manual - Page 8
...Control Head
Chute Support Bracket
Chute
Chute Base
Figure 3-4
Figure 3-6
Chute Directional Control (Model 2410)
2. Push rod as far into chute control head.
Insert the end of the chute ... base. The flange keepers will not easily click into the lower bracket and secure with the flat washer and hairpin clip just removed.
Remove clevis pin and bow-tie cotter pin from chute...
Operation Manual - Page 11
... on the skid shoes.
3. See Fig. 3-16.
2. Figure 3-17 3. Refer to operating the snow thrower. Equal tire pressure should be adjusted by the 4-way Chute Directional Control. Refer to cause serious injury.
Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on models 2840 and 3090XP is not recommended that you...
Operation Manual - Page 17
...auger housing.
3.
To remove skid shoes:
1. NOTE: Augers not shown for information regarding tire pressure. Wipe off any oil on select models) have two wear edges.
When one side... when necessary. Standard Chute Directional Control (Model 2410)
Once a season, lubricate the eye-bolt bushing and the spiral with 3-in -1 oil) to the snow thrower.
2. Tire Pressure
Refer to Fig 7-3.
4. Refer to...
Operation Manual - Page 19
..., follow the storage instructions below. 1. Store in this hole and the chute control rod.
Remove the cotter pin from the engine. 2. Chute Bracket Adjustment (Model 2410)
If the spiral at the bottom of the chute directional control is empty and it stops due
to lack of the engine and the snow...
Operation Manual - Page 22
.... 7-8.
4. Examine the friction wheel for signs of the snow thrower by removing the self-tapping screws which secure it. Stop Bolt
Friction Wheel Removal (Models 2410, 2620 & 2840)
If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to correct the...
Operation Manual - Page 25
... 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires)
Friction Wheel Assembly (Storm 2410, 2620 & 2840) Friction Wheel Assembly (Storm 3090XP) Friction Wheel Rubber
725-1629 725...
Operation Manual - Page 26
... your Troy-Bilt snow thrower. Model Number
Description
753-05762A OEM-390-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410.
Operation Manual - Page 28
...consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to be greater than the original purchaser or... deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber and tires. Normal wear parts include, but are not genuine Troy-Bilt parts. During the period of the ...
Similar Questions
Troy Bilt Snow Blower Engine (storm 2410)
I need to remove the shroud from the engine, and to do so I have to remove the choke knob. Can you t...
I need to remove the shroud from the engine, and to do so I have to remove the choke knob. Can you t...
(Posted by dcook37366 1 year ago)
Troy Built Storm 2410
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
(Posted by brucepieper1 3 years ago)
We Are Finding It Impossible To Attach The Chute To The Snow Blower,storm 2410
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
(Posted by wfingerman 8 years ago)
