Home » Whirlpool » Laundry Washers » Whirlpool WTW4616FW

Whirlpool WTW4616FW Support Question

Find answers below for this question about Whirlpool WTW4616FW.
Need a Whirlpool WTW4616FW manual? We have 6 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by Gabriellekarpyshyn on December 8th, 2017

Final Spin Flashing

my machine won't work as the cycle status is stuck in "final spin". Canceling it won't work, selecting a different setting won't work. Pressing the start/stop button on locks the door.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on December 8th, 2017 11:47 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,690

1,080
points

At http://producthelp.whirlpool.com/Troubleshooting?startid=5065 for top-load washers click Not Starting or Not Operating.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Whirlpool WTW4616FW Manual Pages

Installation Guide - Page 2

... Tools and Parts Gather required tools and parts before starting installation. Tools needed: Parts needed: (Not supplied with washer) Adjustable or open end wrench 9/16" (14 mm... Part Number 367031 Connector Kit Part Number 285835 LOCATION REQUIREMENTS Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area. 271/2" 27" ...

Installation Guide - Page 3

... (with spacing of 0" (0 mm) clearance on washer, and water pressure of drain hose should be needed.) Laundry tub drain system 4.5" (114 mm) 39" (990 mm) Minimum capacity: 20 gal. (76 L). This washer has been tested for closet door ventilation openings which are required. If a closet door or louvered door is your responsibility. To order, please see...

Installation Guide - Page 4

.... n Do not have a fuse in the neutral or ground circuit. 48" (1.2 m) Move washer to within 4 ft (1.2 m) of the customer to the instructions included with a qualified electrician if you start: remove shipping materials It is required. NOTE: To avoid floor damage, set washer onto cardboard before moving it is recommended that a qualified electrician determine that...

Installation Guide - Page 5

... you need additional parts with clamp. Squeeze clamp with pliers and slide black elbow end of laundry tub. See "Tools and Parts". 6. Be sure to move washer later. 4. Drain hose form must be inside standpipe; For a laundry tub or standpipe drain, go to free from tub. For a floor drain, remove the preinstalled drain...

Installation Guide - Page 6

...inlet hoses to water faucets Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to washer correctly. 10. Make note of the drain hose. IMPORTANT: To reduce risk of..., or leaks are only connecting to a cold water faucet, you are found. 11. You may enter washer. NOTE: Both hoses must use a Y-adapter (not provided). 8. If you must be connected to hot...

Installation Guide - Page 7

... final location. or Models with plastic feet If washer is not level: On models with metal feet, when washer is level, skip to step 15, (on models with metal feet) or step 16 (on top edges of washer Place level here Place level here Move the washer to check levelness of washer. 15. Secure drain hose Laundry...

Quick Reference Sheet - Page 1

...final rinse. Lift lid and add measured recommended amount of oil on it will cancel your cycle and drain the washer....PRESS START Press and release START. Press START/ PAUSE to start the washer. 4 SELECT CYCLE Cycles vary by model. 5 SELECT WASH TEMP 6 CYCLE OPTIONS Options vary by filling dispenser to underside of laundry products to determine amount of rim with all cycles, settings...

Dimension Guide - Page 2

...or below the top of washer. (Additional hoses may be at least 39" (990 mm) above floor; ELECTRICAL REQUIREMENTS A 120 volt, 60 Hz., AC only, 15- Select method you will need ...(51 mm). If you must be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right ...

Use & Care Guide - Page 3

... the lid is started, the washer will fill to the selected water level, the lid must be closed . Press START/Stop to the load size. Using non-HE detergent will turn on when in the cycle you must be opened . It may generate a high level of the wash phase. They should be different kinds of spins to reduce suds...

Use & Care Guide - Page 4

... spinout and remain locked for detailed descriptions of cycles. 5 START/STOP BUTTON Press to pause the cycle and unlock the lid. See "Cycle Guide" for the remainder of the cycle. 4 press again to start the selected cycle; Press and hold for your washer. Once sensing is complete, the washer will fill and begin sensing to the Auto Sensing setting. If the lid is spinning, it may be...

Use & Care Guide - Page 5

... the lid after it has been locked, press START/Stop. For best results, remove the load promptly. Press START/Stop while the lid is selected, you will hear the agitator rotate followed by a pause lasting several minutes if the load was spinning at different stages in the wash cycle while the machine performs different wash actions. LID LOCKED The Lock feature allows for proper water...

Use & Care Guide - Page 6

... to drain washer after cancelling a cycle or completing a cycle after power interruption or for normally soiled cottons and mixed-fabric loads. press, linens, synthetics Heavy Regular Lightly soiled noiron fabrics, cottons, perm. Place small items in mesh garment bags before washing. Use this cycle to never-beenworn items indicating "Machine Washable Silks" or "Gentle" cycle on the...

Use & Care Guide - Page 7

... items by recommended cycle, water temperature, and colorfastness. ■■ Separate heavily soiled items from lightly soiled. ■■ Separate delicate items from sturdy fabrics. ■■ Do not dry garments if stains remain after washing because heat can set stains into the basket. Using Your Washer 1. Add a measured amount of laundry products to...

Use & Care Guide - Page 8

...fabric softener into washer. See Max Fill line arrows. Adding Liquid Fabric Softener Manually to choose your load size. Select cycle Turn cycle knob to Wash Load During the final rinse, wait... Softener knob must be set to start the washer. 6. Close the lid and press the START/Stop button again to "Yes" when using the fabric softener dispenser. 3. Load laundry into washer 5. load them in ...

Use & Care Guide - Page 9

... Level knob to start the wash cycle. Select WASH TEMPERATURE The Fabric Softener knob must be set to "Yes" (si) when using the Deep Water Wash (lavado con agua profunda) setting. 9. Press START/Stop to begin wash cycle Press the START/Stop button to the Deep Water Wash (lavado con agua profunda) setting and the washer will light. Once you would like to avoid odor...

Use & Care Guide - Page 10

... turn may increase the rate at its Best 1. If washer will not freeze. Do not place an affresh® Washer Cleaner tablet in new location. Press the START/Stop button to mix antifreeze and remaining water. 3. Select the cycle recommended for a period of detergent to help dry out the washer and prevent the buildup of more than is placed...

Use & Care Guide - Page 11

... the pump making a continuous humming sound with periodic gurgling or surging as final amounts of water are removed during the Drain & Spin cycles. Use half the manufacturer's recommended amount of the basket decelerating. Empty pockets before washing. This is normal. Washer may hear the whirring sound of detergent for flexing or sagging. Check floor...

Use & Care Guide - Page 12

... assistance and to inlet valve. Washer not performing as recommended. Washer won't run or fill, washer stops working, or wash light remains on . Check proper electrical supply. Tighten fill-hose connection. The load will not be attached and have not become clogged. Check that load is normal operation for leaks (laundry tubs, drain pipe, water pipes...

Use & Care Guide - Page 13

... the best cycle. Select the Drain & Spin cycle to drainpipe or tub. See "Using Your Washer" for proper installation. Check drain hose for loading recommendations. remove extra suds, select Rinse & Spin. This includes cooler hot and warm washes. Both hot and cold water faucets must be closed for proper water supply. Close lid and press START/Stop. Do...

Use & Care Guide - Page 15

... spinning. A cycle was stopped or paused using the START/Stop button. Single-dose laundry packet not dissolving Adding laundry packet incorrectly. Do not add packet to avoid snags and tears. Follow the manufacturer's instructions to avoid damage to your load with the lid open for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Washer...

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Using the delay start on my dishwasher
... of hours delayed. Select a wash cycle and option. Press Start/Resume. (The door must be closed.) The delay countdown starts, and the cycle will not continue if the door is locked Lights flashing on my dishwasher? If the door is unlatched, the Start/Resume indicator flashes. The delay countdown stops until it latches. To delay the start: Press the delay button to the load anytime...
Display shows uL - Top-load washer with Dispensers in Corners
... and press Start. Unbalanced load Balanced load Is the washer level? Does the washer rock when pushed against the corners? If the code remains and the wash cycle dial is detected. Display shows oL - washer display shows uL. This error code indicates that an unbalanced load is flashing after the recovery routine has stopped, open...
Vibration - Top-load washer
... from the washer. Tilt the washer forward until the rear of the washer is normal. Do you will result in different homes, depending on the diagonal. If the washer teeters, adjust...front feet lock nuts against the bottom of how the washer may sound during the final spin portion of the washer with shipping material still inside. If the load is vibrating. The washer must ...