Zenith SL-5512-BZ-B Support Question
Zenith SL-5512-BZ-B Support Question
Find answers below for this question about Zenith SL-5512-BZ-B - Heath - Quartz Halogen Motion-Sensing Twin Security Light.Need a Zenith SL-5512-BZ-B manual? We have 1 online manual for this item!
Question posted by acahorvath on December 10th, 2010
Light Stays On All Night
I would like to have the light operate only when sensor senses movement only.
Current Answers
Related Zenith SL-5512-BZ-B Manual Pages
User Guide - Page 1
... TEST and the DualBrite® switch OFF. TEST 1 5 20
DualBrite®
Off 3 6 Dusk to use in wet locations. DualBrite® Twin Halogen Motion Sensing Light
Model SL-5512
Requirements
• The light control requires 120-volts AC. • If you want to Dawn
Sensor Light Control
3 Wire Connectors
AUTO
Put the ON-TIME switch in the 1, 5, or 20 minute position.
User Guide - Page 2
If motion is mounted higher than 3 feet (1 m). • Use only T3, 150W (max.) tungsten halogen 120 VAC lamps. INSTALLATION
For easy installation, select an existing light operated by a wall switch for the ON-TIME (1, 5, or 20 minutes) then returns to dim mode. NOTE: If fixture is sensed, the light turns on full bright for replacement. The bulb...
User Guide - Page 3
...bulb push
the junction box. Bulb Installation
Mount the Light Control
NOTE: Lamps are inside
❒ Open glass covers. from the sensor.
Note: All ground wires shown as green in the... circuit breaker or fuse.
❒ Remove the existing light fixture.
❒ Install mounting strap to hold the fixture
while wiring.
Secure the fixture
bulb is seated properly. ❒ Close...
User Guide - Page 4
...want the lights to stay
on after motion is mounted higher than 8 ft.(2.4 m), aiming the sensor down , or
sideways to change temperature rapidly, such as needed. Keep the sensor at the sensor.
240&#...may trigger the control.
• Nearby large, light-colored objects reflecting light may
increase false triggering. ❒ Secure the sensor head by
tightening the clamp screw.
TEST AND...
User Guide - Page 5
... be sensing small animals or automobile traffic.
2. The fixture is loose or burned out. 3. or 6 hr. Verify wiring is positioned too close to the light control or pointed at any time without incurring any obligation to -Dawn setting.
TEST, AUTO and MANUAL MODE Time Delay 1, 5, 20 minutes Replacement lamp. . . .
Reduce range. 3.
light. Lights stay on...
User Guide - Page 6
... YEAR LIMITED WARRANTY
This is a "Limited Warranty" which vary from the date of Purchase. Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other rights which gives you . Unauthorized service or modification of the product or of incidental or consequential damages, so the above limitation...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
Zenith Hologen Motion Sensor Light
How do I adjust it so that both lights come on with motion and not just one>
How do I adjust it so that both lights come on with motion and not just one>
(Posted by drwoggon 9 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)