Makita 4101RH Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita 4101RH manuals!
Problems with Makita 4101RH?
Ask a Question
Free Makita 4101RH manuals!
Problems with Makita 4101RH?
Ask a Question
Popular Makita 4101RH Manual Pages
Owners Manual - Page 1
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Tile Cutter
125 mm (5") MODEL 4101RH
003504
INSTRUCTION MANUAL
WARNING: For your personal safety, READ and UNDERSTAND before using. www.makitatools.com
Owners Manual - Page 2
...and understand all instructions listed below, may result in accordance with a qualified electrician if you to change specifications without notice. • Specifications may ignite the dust or fumes.
3.
SPECIFICATIONS
Model Wheel diameter
90° Max. Cluttered benches and dark areas invite accidents.
2. Grounded tools must be plugged into an outlet properly installed and grounded in...
Owners Manual - Page 3
...plugging in tools that have the tool serviced before plugging in the hands of ...if your body is grounded.
6. Replace damaged cords immediately. Loose clothes, ... A wrench or a key that cannot be repaired.
18. Use the correct tool for appropriate conditions...support the workpiece to carry electricity away from heat, oil, sharp edges or moving parts, breakage of the tool...
Owners Manual - Page 4
...instructions may become hazardous when used on another tool. Service or main-
Table 1 shows the correct size to fit the proper grounding type receptacle. The tool is the grounding wire. "A".
4
Your unit is in doubt, use only identical replacement parts. tenance performed by qualified repair.... The green (or green and yellow) conductor in a risk of this manual.
model.
Owners Manual - Page 5
... unsafely or incorrectly, you use ) replace strict adherence to jump backwards. (See "Causes and Operator Prevention of control.
6. C
SPECIFIC SAFETY RULES
USB071-1
DO NOT let comfort or familiarity with a "live " and shock the operator.
5 If you can suffer serious personal injury.
1. KICKBACK could cause the tool to cutter safety rules. Do not reach...
Owners Manual - Page 6
...toward the operator. Large panels tend to resist KICKBACK forces. Unsharpened or improperly set wheels produce narrow kerf causing excessive friction, wheel binding and KICKBACK. When operating ... edge of the panel. When ripping always use wheels with proper hand support, proper workpiece support, and supply cord routing away from the workpiece as given below: Maintain...straight edge guide.
Owners Manual - Page 7
... disc.
20. Receptacles are available having built-in this instruction manual may be used for cracks or damage before cutting.
17. 12. Check the wheel carefully for this tool.
15. If the plug or receptacle does get wet, DO NOT unplug the cord. Replace cracked or damaged wheel immediately.
14. This can lead...
Owners Manual - Page 9
... supply and test the Ground Fault Circuit Interrupter (GFCI) before adjusting or checking function on the depth guide and move the base
1
up or down. Push the TEST (T) button and confirm that the pilot...the front of cut , secure the base by tilting accordingly, then tighten the wing nut securely.
1. Set for the desired angle (0° - 45° ) by
tightening the wing bolt.
1.
At ...
Owners Manual - Page 11
Then
2 remove the hex socket head bolt and outer flange.
1
1. Part name
Pressure regulator
Adaptor Vinyl tube Water pipe
Pressure regulator assembly
Use the pressure regulator assembly to connect to install or remove the
wheel.
Outer flange 4.
It consists of water flow
11 Hold the outer flange with the wrench
and tighten the...
Owners Manual - Page 13
...switched off and unplugged before attempting to be cut should not be sure that its side with progressively deeper settings. Now simply move the tool forward in the cut can cause overheating of the motor and dangerous kickback of... an old discarded coarse grit bench grinder wheel or con-
13
003543 Installing cover (A)
Install the cover (A) on the tool so that the tool is completed.
Owners Manual - Page 15
...maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Brush holder cap 2. The use of any assistance for its stated purpose. Only use with your local Makita service center.
• Diamond wheels
• Hex wrench 5
• Wrench 22
• Rip fence (guide rule)
• Pressure regulator assembly
15
Take...
Owners Manual - Page 18
...CODE
AGE:
Under 19
20-29
30-39
40-49
50-60
Over 60
BE SURE TO COMPLETE THE CUSTOMER'S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Any comments:
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
DATE PURCHASED
MONTH
DAY
YEAR
MODEL...to the following questions are : Design Features Size Price Makita Brand
Repair Service
Durability
Power
Other (
)
5. How did you...
Owners Manual - Page 19
...service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to the outside of the carton detailing the problem with your tool.
Date Purchased Dealer's Name & Address
Model...45246 (513) 771-0788
OKLAHOMA 552 E. Be sure to attach a letter to an Authorized Makita Service Center. Windsor Locks, CT 06096 (860) 292-6405
FLORIDA 620 Douglas Ave. Westwood, MA...
Owners Manual - Page 20
... Service Centers. This Warranty does not apply where:
• repairs have other reproductive harm. This Warranty gives you specific legal rights, and you do not allow limitation on how often you may not apply to you .
884156D067
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan WARNING
Some dust created by power sanding, sawing...
Parts Breakdown - Page 2
...8-85, HP2010N POWER SUPPLY CORD UNIT CORD
CORD CORD DUST COVER, 4101RH SWITCH,4100NH CARBON BRUSH CB-303 SET, 9227C CARBON BRUSH SET CB-303, 9227C BRUSH HOLDER CAP, JR3020
Page 2 of 3
Quantity...Part Name HEX BOLT M6X20, 5620DWA OUTER FLANGE, 4200H N/A
INNER FLANGE, 4200H N/A
O RING 18, 4200H BEARING RETAINER, 4100NH SPINDLE, 4200H WOODRUFF KEY 4, HM1810 HEX BOLT M4X25, 4101RH BLADE CASE CPL.,4101RH...
Makita 4101RH Reviews
Do you have an experience with the Makita 4101RH that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!