Makita XCU03Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XCU03Z manuals!
Problems with Makita XCU03Z?
Ask a Question
Free Makita XCU03Z manuals!
Problems with Makita XCU03Z?
Ask a Question
Popular Makita XCU03Z Manual Pages
XCU03 Instruction Manual - Page 2
... to EPTA-Procedure 01/2003
WARNING: Use appropriate combination of the guide bar and saw chain. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Overall length (without guide bar)
Rated voltage Standard battery cartridge
Net weight (when using BL1815N)
with 90PX with 91PX
Guide bar
Guide bar length
Cutting length
Saw chain type (refer to the table below)
Sprocket
Number of teeth...
XCU03 Instruction Manual - Page 4
...chain saw safety warnings
1. Service
1. Hold the power tool by a qualified repair person using only identical replacement parts. Use extreme caution when cutting brush and saplings. Follow instructions for lubricating and changing accessories.
3. Improperly tensioned or lubricated chain may cause chain... you start the chain saw, make exposed metal parts of the guide bar touches an ...
XCU03 Instruction Manual - Page 5
... use ) replace strict adherence to drop or strike battery.
9.
Tape or mask off open contacts and pack up the battery in a con- It will also void the Makita warranty for battery cartridge
1.
ductive material. (2) Avoid storing battery cartridge in such a manner that the chain saw chain and guide bar
Important safety instructions for the Makita tool and...
XCU03 Instruction Manual - Page 8
...pulled under unoperatable conditions.
NOTE: This chain saw , press the main power switch until the main power lamp lights up for proper repairs BEFORE further usage. NEVER use the...
8 ENGLISH CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to our authorized service center for few seconds.
...
XCU03 Instruction Manual - Page 9
... pull the switch trigger hard without pressing the lock-off lever is performed, the saw may not be adjusted using the chain saw and consult our authorized service center. CAUTION: Should the saw chain not stop immediately when this test, stop within one second in contact with both hands when switching it on.
XCU03 Instruction Manual - Page 12
...When filling the chain oil for Makita chain saws or ...and balance at all parts of the chain saw chain is 200 ml.
The... use a safe support (saw chain oil exclusively for ...guide bar to wobble, resulting in the oil tank periodically. Start it .
Otherwise it may harm trees.
Check the amount of oil is adequate. The proper amount of remaining oil in injury to hold the chain...
XCU03 Instruction Manual - Page 13
... further down the timber and raise the front handle again. When limbing, support the chain saw may only be used for cutting, the chain saw on the felled trunk when limbing. Pay particular attention to -grain ...trapped. Burrowing and parallel-to-grain cuts
CAUTION: Burrowing and parallel-to guide it. Do not cut with special training. For this presents a risk of kickback. Rest the bottom ...
XCU03 Instruction Manual - Page 15
... be replaced with following distance between the depth gauge (round nose) and the cutting edge.
- The file holder has markings for the correct sharpening angle of the saw chain when: • Mealy sawdust is produced when damp wood is obviously damaged; • The saw chains to the left or right in our authorized service...
XCU03 Instruction Manual - Page 16
... discharge hole
Small dust or particles may be built up in the guide bar groove. Remove the sprocket cover and saw chain on the whole saw dust. Clean out the chips and sawdust every time when you sharpen or replace the saw chain. These dust or particles may clog the bar groove and impair...
XCU03 Instruction Manual - Page 17
... cover.
4. Before operation
Everyday - Before storage
- Saw chain
Inspection.
-
-
-
-
-
Locking ring 2.
authorized
service center. necessary. Every week -
Areas to perform the prescribed maintenance work which is installed as shown in the instruction manual. Annually - Check at
authorized
service center.
-
- Guide bar
Inspection.
-
-
-
- inspected
regularly at...
XCU03 Instruction Manual - Page 18
...performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts for repair. The motor stops running after the main power switch is turned on and the chain brake is automatically turned off . Battery problem (low voltage). Chain brake activated.
Install the battery cartridges as described in the manual, do not attempt to dismantle the tool. Loose guide bar...
XCU03 Instruction Manual - Page 19
... trouble is caused by others:
• repairs are recommended for use with your local Makita Service Center. • Saw chain • Guide bar • Guide bar cover • File • Tool bag • Makita genuine battery and charger
WARNING: If you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace...
XCU03Z Parts Breakdown - Page 2
... COMPLETE CAUTION LABEL XCU03 NAME PLATE HOUSING SET CAUTION LABEL INC. 2 TAPPING SCREW 4X18.... 1 1 1 PC. 1 1 1 1 1 0 8 PC. 3 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. Model XCU03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
810X87-6
002
183F24-8
002 C10 810R30-9
002 D10
003
266326-2
004
457007-1
005
266326-2
006
457013-6
007...
XCU03Z Parts Breakdown - Page 3
... SCREW 4X18 SPIKE BUMPER TAPPING SCREW 4X18 CHAIN CATCHER TAPPING SCREW 4X18 GUIDE PLATE ES TAPPING SCREW CT 3X8 GUIDE PLATE CS STRAIGHT BEVEL GEAR 14 ADJUST PIN ADJUST SCREW TAPPING SCREW 4X12 NUT COMPLETE NUT COVER SPROCKET COVER WHEEL COMPLETE O RING 7 O RING 10 GUIDE BAR CHAIN COVER SAW CHAIN SET
1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC...
Makita XCU03PT New Tool Flyers English - Page 1
... reduced operator fatigue
SPECIFICATIONS
Guide Bar Length Chain Speed Chain Pitch Chain Gauge Battery Overall Length UPC Code (XCU03Z) UPC Code (XCU03PT)
Also Available as a Bare Tool Model XCU03Z
14" 3,940 FPM
3/8" .043" 2X 18V LXT® Lithium-Ion 30-1/2" 088381-832731 088381-838917
STANDARD EQUIPMENT
XCU03PT 18V LXT® Lithium-Ion 5.0Ah Battery (BL1850B) 18V LXT® Lithium-Ion...
Makita XCU03Z Reviews
Do you have an experience with the Makita XCU03Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!