Makita 9564P Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita 9564P manuals!
Problems with Makita 9564P?
Ask a Question
Free Makita 9564P manuals!
Problems with Makita 9564P?
Ask a Question
Makita 9564P Videos
Makita 4-1/2 in. 10 Amp Paddle Switch Angle Grinder - 9564P
Duration: 1:01
Total Views: 125
Duration: 1:01
Total Views: 125
Popular Makita 9564P Manual Pages
Owners Manual - Page 1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
Angle Grinder
9564P 9565P
DOUBLE INSULATION
013574
IMPORTANT: Read Before Using. 1
Owners Manual - Page 2
... equipment. Avoid body contact with earthed (grounded) power tools. Do not expose power tools to follow the warnings and instructions may ignite the dust or fumes. 3.
Do not operate power tools in the warnings refers to a power supply of their meaning before use any way. ENGLISH (Original instructions)
SPECIFICATIONS
Model
9564P
9565P
Depressed center wheel diameter
115 mm...
Owners Manual - Page 3
... you are caused by a qualified
repair person using only identical replacement parts. If operating a power tool in electric shock, fire and/or serious injury. 2. Keep cutting tools sharp and clean. Follow instruction for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations: 1. Disconnect the plug from the power source and/or the battery pack from oil and grease...
Owners Manual - Page 4
... proper precautions are not specifically designed and recommended by flanges, the arbour hole of the accessory must wear personal protective equipment. For accessories mounted by the tool manufacturer. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at your side. Wear...
Owners Manual - Page 5
... position your power tool and the specific guard designed for the selected wheel. b) The grinding surface of centre depressed wheels must be different from grinding wheel flanges. d) Wheels must be securely attached to the power tool and positioned for maximum safety, so the least amount of a smaller tool and may burst. Proper wheel flanges support the wheel...
Owners Manual - Page 6
...and could burn your skin. 25. The tool may result in the wheel is properly supported. 30. Damage to these parts could indicate poor installation or a poorly balanced wheel. 22. ...lateral pressure. Observe the instructions of the manufacturer for this instruction manual may cause switch breakage. For tools intended to be damaged. Do not use ) replace strict adherence to safety...
Owners Manual - Page 7
...the tool is installed
securely before carrying out any work on the tool. Installing side grip (handle)
For tool with the notch on the tool so that the closed side of the tool as shown in reverse. Installing or...fitted on the bearing box. The setting angle of the arrow for use the lock nut wrench
7 To remove wheel guard, follow the installation procedure in the direction of the ...
Owners Manual - Page 8
... cutting blades and other on a grinder frequently kick and cause loss of control leading to force the tool.
Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is in the B direction or it may be worked in reverse. To remove the wheel, follow the installation procedure in both A and...
Owners Manual - Page 9
...to the table
below.
115 mm (4-1/2") / 125 mm (5")
Abrasive cut -off wheel for
abrasive cut moving the tool forward over the workpiece surface. Lock nut
2. Abrasive cut -off
2
wheel/diamond
3
wheel
4
3. Wheel guard...make an excessive depth of the motor may bind, walk up or kickback if the power tool is started in grinding) will cause the wheel to twisting or binding of the wheel...
Owners Manual - Page 10
... should be performed by running
tool with no load, insuring that no one is in front of or in this manual. Unplug tool and place it upside down ...kept clean. When using Makita replacement parts. Operation with wire wheel brush (optional accessory)
1. Wire cup brush
1
008384
CAUTION: • Check operation of brush by Makita Authorized Service Centers, always using brush...
Owners Manual - Page 11
• Lock nut for depressed center wheel / abrasive cut-off wheel / flap disc / diamond wheel
• Lock nut for abrasive disc • Lock nut wrench • Side grip • Rubber pad • Dust cover attachment NOTE: • Some items in the list may differ from country to country.
11 They may be included in the tool
package as standard accessories.
Flyer (English) - Page 1
... bydeflecting dust &debris
COMFORT
Model 9564P
Large paddle switch with Lock-off and no lock-on feature
INNOVATION & PERFORMANCE. Armature continues
to slip.
If the wheel is forced to stop, the spring is spring loaded. 4-1/2'' ANGLE GRINDER
SJS TECHNOLOGY PROTECTS MOTOR AND GEARS • Powerful 10.0 AMP Motor Delivers More Output and 10,500 RPM for the...
Flyer (English) - Page 2
... accessories. Model 9564P
4-1/2'' ANGLE GRINDER
FEATURES & BENEFITS
n Powerful 10.0 AMP motor delivers more output and 10,500 RPM for the most demanding applications
n Super Joint System® (SJS) technology helps prevent motor and gear damage by deflecting dust and debris
n Labyrinth construction seals and protects the motor and bearings from dust and debris for longer tool life
STANDARD...
Makita 9564P Reviews
We have not received any reviews for Makita yet.