Asus ESC4000-E10S Support and Manuals
Get Help and Manuals for this Asus item
View All Support Options Below
Free Asus ESC4000-E10S manuals!
Problems with Asus ESC4000-E10S?
Ask a Question
Free Asus ESC4000-E10S manuals!
Problems with Asus ESC4000-E10S?
Ask a Question
Popular Asus ESC4000-E10S Manual Pages
User Manual - Page 7
... power supply is intended for installation only in a Computer Room where: • Access can only be gained by SERVICE PERSONS or by USERS who have been
instructed about the reasons for assistance ... certified or experienced engineers.
• Before operating the server, carefully read all the manuals included with the server package.
• Before using the server, ensure all cables are...
User Manual - Page 9
... provides instructions for installing the necessary drivers for system integrators, and experienced users with the server. Contents
This guide contains the following parts: 1. Chapter 2: Hardware Setup This chapter lists the hardware setup procedures that comes with at least basic knowledge of the server, including sections on front panel and rear panel specifications. 2. About this guide...
User Manual - Page 10
.... 1. Typography
Bold text
Indicates a menu or an item to set up and use the proprietary ASUS server management utility. 2.
IMPORTANT: Instructions that you must press the Enter or Return key.
++ If you MUST follow to complete a task. ASUS websites
The ASUS websites provide updated information for all ASUS hardware and software products.
NOTE: Tips and additional information...
User Manual - Page 13
1.3 System specifications
The ASUS ESC4000-E10S Series servers features the ASUS Z12PG-D16 server board that supports Intel® 3rd Gen Xeon® Scalable Processors. ASUS PIKE II 3008 8-port SAS HBA Card - Model Name Processor / System Bus
ESC4000-E10S Intel® 3rd Gen Xeon® Scalable Processors (up to 235W)
Memory
Total Slots Capacity
Memory Type
16 (8 channel per CPU...
User Manual - Page 25
... the protection film before shipping. To remove the middle chassis cover: 1. Push and hold the cover buttons down on the system for proper heat dissipation. ASUS ESC4000-E10S
2-3
Lift the chassis cover to completely remove it from the chassis.
2 1
A protection film is pre-attached to completely remove it from the chassis. 2. Lift the...
User Manual - Page 43
...Reconnecting the cable to the M.2 expansion board (only for PCIe slot to your system comes with the M.2 expansion board pre-installed. 1. (optional) Remove the two (2) slimline SAS cables from the internal riser board for SKU-3)
You may reconnect the ....
The cables are connected by default if your system package comes with the slimline SAS cables connected.
2. ASUS ESC4000-E10S
2-21
User Manual - Page 45
Secure the M.2 card with the screw you removed in step 2.
ASUS ESC4000-E10S
2-23 Locate the M.2 connector (NGFF1) on the motherboard. 1. Prepare the M.2 card, then align and insert the M.2 card into the M.2 connector (NGFF1). 4. 2.5.4 Installing an M.2 (NGFF) card
You may install an M.2 card (supports up to 22110) to the onboard M.2 (NGFF) slot on the motherboard.
2. Remove the...
User Manual - Page 47
Connect the white 4-pin power connector to the 4-pin power connector on the OCP3.0 slot baseboard.
2 1
2 1
ASUS ESC4000-E10S
2-25 3.
User Manual - Page 49
...an IRQ to the Standard Interrupt assignments table for the expansion card.
ASUS ESC4000-E10S
2-27 Turn on BIOS setup.
2. See Chapter 5 for ISA or PCI devices. Refer to...change the necessary BIOS settings, if any. 2.5.7 Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1. Install the software drivers for more information.
3....
User Manual - Page 51
ASUS ESC4000-E10S
2-29
2.7 SATA/SAS backplane cabling
connect to support 2 NVMe devices. With two mini-SAS HD cables connected, a total number of 8 SAS/SATA HDDs can be supported
connect to SLIMPCIE2 on the motherboard to ISATA1 and ISATA2 on the motherboard.
User Manual - Page 53
Connect two (2) slimline SAS cables to SLIMPCIE5 and SLIMPCIE6
ASUS ESC4000-E10S
2-31 Connect the slimline SAS cables to the SLIMPCIE5 and SLIMPCIE6 slots located on the backplane. 3.
User Manual - Page 55
Lift the fan then set it aside. 3. Ensure the
fan connector is seated firmly within the cable holder. Repeat steps 1 to 2 to release the system fan from the fan cage. 2.
... the other system fans.
To reinstall the system fans: 1. 2.8.2 System fans
To uninstall the system fans: 1. Insert the fan into the fan cage. cable holder
ASUS ESC4000-E10S
2-33
User Manual - Page 119
...Disable] Allows you to enable or disable Whea Log PCI Error. Configuration options: [Disable] [Enable]
ASUS ESC4000-E10S
5-27
Whea Log Memory Error [Enable] Allows you to enable or disable Whea support. Configuration options: [Disable] [Enable]
The following items are only available when System Errors is set to [Enable]. Configuration options: [Disable] [Enable]
The following items...
User Manual - Page 121
...] Enable & escalate Uncorrectable/Recoverable to select the Patrol Scrub Error type selection. Configuration options: [Disable] [Enable] Error Control Setting
Patrol Scrub Error Reporting [UCNA] Allows you to error pins. Configuration options: [Disable] [Enable]
ASUS ESC4000-E10S
5-29 IIO Error Enabling
IIO/PCH Global Error Support [Enable] Allows you to enable or disable Clear IIO...
User Manual - Page 151
Configuration options: [Disabled] [Enabled]
The following items are available only when BMC Support is set to change the settings. OS Watchdog Timer [Disabled] This item allows you to [Enabled]. Configuration options: [1] - [30]
ASUS ESC4000-E10S
5-59 OS Wtd Timer Timeout [10] Allows you to enter a value between 1 to communicate with BMC. Helps determine if the OS successfully...
Asus ESC4000-E10S Reviews
We have not received any reviews for Asus yet.