Honeywell 3800G14-USBKITE Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell 3800G14-USBKITE manuals!
Problems with Honeywell 3800G14-USBKITE?
Ask a Question
Free Honeywell 3800G14-USBKITE manuals!
Problems with Honeywell 3800G14-USBKITE?
Ask a Question
Popular Honeywell 3800G14-USBKITE Manual Pages
User Manual - Page 15
... most common terminal and communications settings.
The chart below to the chart below lists the 3800g imager models. Refer to determine the models that can be used with many interfaces, which are described in this User's Guide. 1
Getting Started
About This Manual
This User's Guide provides installation and programming instructions for programming information regarding...
User Manual - Page 17
... CDC class device and automatically uses a class driver. CTS/RTS Emulation
On
* Off
3800g User's Guide
1 - 3
IBM SurePos (USB Handheld Scanner) Interface
IBM SurePos (USB Tabletop Scanner) Interface
USB HID
Scan the following code to program the 3800g to emulate a regular RS-232based Com Port.
The driver will need to download a driver from the Hand Held Products website (www.handheld...
User Manual - Page 25
Supported Terminals (Continued)
Terminal Telex 122 key
USB PC Keyboard USB Mac Keyboard USB Com Port USB HIDPOS * Factory default setting
Model(s)
078, 078A, 79, 80, 191, 196, 1191,1192, 1471, 1472, 1476, 1477, 1482, 1483
Terminal ID 046
124 * 125 130 131
3800g User's Guide
2 - 3
User Manual - Page 37
... 3-4). Default = 5,000 ms.
Hands Free Time-Out
Reread Delay
This sets the time period before the imager can set the time the imager should remain in manual trigger mode by setting the Hands Free Time-Out. Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from...
User Manual - Page 38
... set the delay (from the inside back cover of Centering Window
3 - 6
3800g User's Guide
To change the left or right edge of the centering window, scan Centering On, then scan one of view so the imager reads only the bar code you want. Centering On Left of Centering Window
* Centering Off Right of this manual...
User Manual - Page 42
... Code 128, 9999 = all lengths 43 start character match for Code 93, 43h = "C" FF termination string for Code 93 9999 code length that must be enabled to count any programmed prefixes, suffixes, or formatted characters as part of the length. Code 93
You would set up the sequence editor with the following command line:
SEQBLK62001141FF6A001242FF69001143FF
3 - 10
3800g User's Guide...
User Manual - Page 49
...manual.
3800g User's Guide
4 - 5 Next, scan the Character to 0. Scan the Intercharacter Delay bar code below , then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual...the Intercharacter Delay bar code, then set the number of steps to 0. Note: Intercharacter delays are not supported in USB serial emulation. Intercharacter...
User Manual - Page 52
...of this manual This exits, saving any Data Format changes. For example, scan 0 0 3 for the numeric value
5 - 2
3800g User's Guide In ...the Supported Terminals Chart on page 2-2), Code I .D. Scan Save from the Programming Chart inside the back cover of this manual ...an ASCII code, see ASCII Conversion Chart (Code Page 1252) on page A-1), and the bar code data length for the specific data ...
User Manual - Page 59
..., the imager changes to manual trigger mode. Default = 5,000 ms.
Hands Free Time-Out
3800g User's Guide
6 - 3
Note: If...code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover, and Save. Hands Free Time-Out
The Automatic Trigger and Presentation Modes are referred to the original hands free mode. You can set the time the imager should remain in manual...
User Manual - Page 66
... end of the scanned data. Minimum and Maximum lengths = 0-48. Code 39 Check Character
No Check Character indicates that the imager reads and transmits bar code data with the scanned data. Minimum Message Length
Maximum Message Length
7 - 6
3800g User's Guide When Check Character is set to Message Length on page 7-2 for additional information.
Refer to...
User Manual - Page 72
... (three-bar start /stop )
Straight 2 of 5 Industrial
On * Off
Straight 2 of 5 IATA (two-bar start /stop )
7 - 12
3800g User's Guide Minimum Message Length Maximum Message Length
Straight 2 of 5 Industrial Message Length
Scan the bar codes below to Message Length on page 7-2 for additional information. Minimum Default = 4, Maximum Default = 48. Minimum and Maximum lengths...
User Manual - Page 76
...7 - 16
3800g User's Guide However, if you wish to transmit Code 128 function codes with Code 128 bar code data. The data characters should then appear properly. Minimum Message Length
Maximum Message Length
Code 128 Code Page
Code pages define the mapping of Printed Bar Codes on page 7-2 for additional information.
Minimum and Maximum lengths = 0-80. If this manual. Minimum...
User Manual - Page 88
RSS-14
< Default All RSS-14 Settings >
RSS-14
* On Off
RSS Limited
< Default All RSS Limited Settings >
RSS Limited
* On Off
RSS Expanded
< Default All RSS Expanded Settings >
7 - 28
3800g User's Guide
User Manual - Page 119
Selection
Setting * Indicates default
UPC E Expand
UPC E Check Digit
UPC E Number System
UPC E 2 Digit Addenda
UPC E 5 Digit Addenda
...On *Off On *Off On *Not Required Required Off *On *Off On Default All EAN/ JAN 8 Settings Off *On
3800g User's Guide
Serial Command # Indicates a numeric entry
UPEEXP0 UPEEXP1 UPECKX0 UPECKX1 UPENSX0 UPENSX1 UPEAD20 UPEAD21 UPEAD50 UPEAD51 UPEARQ0 UPEARQ1 UPEADS0...
User Manual - Page 129
... information about cable replacement. 13
Maintenance
Repairs
Repairs and/or upgrades are not to be performed only by an authorized service center. abrasive wipes may damage the finish or the window.
A badly worn cable or damaged connector may also be performed on the housing or window - Please see Customer Support on page 13-2.
3800g User's Guide
13 - 1
Caution...
Honeywell 3800G14-USBKITE Reviews
We have not received any reviews for Honeywell yet.