Makita XHU04Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XHU04Z manuals!
Problems with Makita XHU04Z?
Ask a Question
Free Makita XHU04Z manuals!
Problems with Makita XHU04Z?
Ask a Question
Popular Makita XHU04Z Manual Pages
XHU04Z Instruction Manual - Page 1
IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar. 1 INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Hedge Trimmer Taille-haie sans fil Cortasetos Inalámbrico
XHU04
014621
IMPORTANT: Read Before Using.
XHU04Z Instruction Manual - Page 2
... tools to a rotating part of flammable liquids, gases or dust. BL1815N/BL1820
BL1830/BL1840/BL1850
Net weight
4.7 kg (10.3 lbs)
5.2 kg (11.4 lbs)
• Due to lose control. Power tool plugs must match the outlet. Use of an GFCI reduces the risk of electric shock. 5. ENGLISH (Original instructions)
SPECIFICATIONS
Model Blade length Strokes per...
XHU04Z Instruction Manual - Page 3
...off when clearing jammed material. Carry the hedge trimmer by a qualified
repair person using only identical replacement parts. Proper handling of starting the power tool ...serviced by the handle with specifically designated battery packs. Use the correct
power tool for operations different from blade. Use of dust extraction and collection facilities, ensure these instructions...
XHU04Z Instruction Manual - Page 4
...or transport the trimmer with clear water and seek medical attention right away. Clean the hedge trimmer and especially the cutter after use ) replace strict adherence
to follow the safety rules stated in this
instruction manual may result in...
failure to safety rules for damage, and if damaged repair immediately. 16. WARNING:
DO NOT let comfort or familiarity with your attention will be hung on ...
XHU04Z Instruction Manual - Page 5
... the indicators light up.
5 Never recharge a fully charged battery cartridge. CAUTION: • Always install the battery cartridge fully until it is equipped with room temperature at 10 ﾟ C - 40... the motor to drop or strike battery. 9. Overcharging shortens the battery service life.
3. SAVE THESE INSTRUCTIONS. Charge the battery cartridge once in damage to the tool and battery ...
XHU04Z Instruction Manual - Page 6
...: • Always make sure that the switch trigger actuates properly and returns to 6 (full speed).
6 Speed change
1. Adjusting dial 1
014623
The strokes per minute can set the angle of the handle either one of the switch triggers.
Star marking
012128
Overdischarge protection
1
1. By further use, the tool stops and the battery...
XHU04Z Instruction Manual - Page 7
...
CAUTION: • Be careful not to the table below for the relationship between the number settings on the tool when trimming the hedge straight can be turned only as far
as a reference...blades towards the trimming direction and move it helps to cut branches thicker than 10 mm diameter with this trimmer. These should first be trimmed
3. Failure to 1. Do not force it as 6 and back to ...
XHU04Z Instruction Manual - Page 8
... removing chip receiver (optional accessory)
CAUTION: • Always be installed on the tool
with the nuts on both sides so that the chip receiver does not contact branch catcher at the top of the tool.
1
1. NOTE: • When replacing the chip receiver, always wear
gloves so that its hooks locked in the...
XHU04Z Instruction Manual - Page 9
...Clean out the tool by wiping off and the battery cartridge is removed. • When replacing the shear blade, always wear gloves without removing blade cover so that the tool is
applied...cause damage to the tool. • For specific way of removing and installing shear
blades refer to do so may result. Blade cover
2
2. Blade cover 3. Plate
011159
Set the crank at the angle as machine oil...
XHU04Z Instruction Manual - Page 10
...in such a
manner as shown in the shear blades fit onto the crank. Adjust the crank position as it was installed if it should be taken away by mistake. Oval hole of
1
shear blade
011259
Take out the blade cover from... from the old shear blades and fit it for easy handling during the replacement of the plate. At this time, apply some grease provided with a slotted screwdriver.
1.
XHU04Z Instruction Manual - Page 11
...screwdriver to the limit mark. Storage The hook hole in this manual. Store the tool out of the reach of slotted screwdriver into...on the tool. To maintain product SAFETY and RELIABILITY, repairs, any other accessories or attachments might present a risk ... cap cover by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Reinstall the holder cap cover on the...
XHU04Z Instruction Manual - Page 12
... AND AFTER THE TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. EN0006-1
12 Should any trouble develop during this one year period, return the COMPLETE tool, freight...
XHU04Z Parts Breakdown - Page 2
Model XHU04Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
265995-6 TAPPING SCREW 4X18
002
452164-0 KNOB
003
455093-6 LOCK OFF LEVER
004
455091-0 SWITCH LEVER A
005
650730-9 SWITCH TG72BD-6
006
187879-7 HANDLE SET...
452162-4 LOCK LEVER
015
455092-8 SLIDER
016
187879-7 HANDLE SET
016 C10 263005-3 RUBBER PIN 6
016 C20 803N80-7 INDICATION...
XHU04Z Parts Breakdown - Page 3
... +TRUSS HEAD SCREW M5X20
045 C40 345205-8 BRANCH CATCHER
045 C50 911208-0 PAN HEAD SCREW M5X10
045 C60 188605-7 OIL VESSEL SET
046
346325-1 PLATE
047
253835-0 FLAT WASHER 8
048
211032-4 BALL BEARING 608ZZ
049
265182-7 + PAN HEAD SCREW M5X25
050
452156... 608ZZ
043
253835-0 FLAT WASHER 8
044
142215-4 GEAR COMPLETE
045
196689-1 SHEAR BLADE ASSEMBLY SET
045 C10 264013-7 HEX.
Makita XHU04Z Reviews
We have not received any reviews for Makita yet.