Ariens Power Brush 36 Support and Manuals
Get Help and Manuals for this Ariens item
View All Support Options Below
Free Ariens Power Brush 36 manuals!
Problems with Ariens Power Brush 36?
Ask a Question
Free Ariens Power Brush 36 manuals!
Problems with Ariens Power Brush 36?
Ask a Question
Most Recent Ariens Power Brush 36 Questions
Power Broom Bucks When Sweeping Snow And Is Difficult To Control Is There An A
is there an adjustment for this
is there an adjustment for this
(Posted by Mafh 2 years ago)
Ariens Power Brush 36 Videos
Ariens Hydro Power Brush 36" Demo
Duration: 1:49
Total Views: 65
Duration: 1:49
Total Views: 65
Zamiatarka ca?oroczna ARIENS Power Brush 36 Hydro
Duration: 3:44
Total Views: 287
Duration: 3:44
Total Views: 287
Ariens Power Brush 36 inch *caster wheel mod* Pt 2/2
Duration: 1:43
Total Views: 323
Duration: 1:43
Total Views: 323
Ariens Power Brush 36 inch *caster wheel mod* Pt 1/2
Duration: 1:38
Total Views: 1,714
Duration: 1:38
Total Views: 1,714
Popular Ariens Power Brush 36 Manual Pages
Owners Manual - Page 3
... claims meeting requirements during the limited warranty period will help the company process warranty claims or contact you do not understand or have purchased this manual may void the warranty. • Record Unit Model and Serial number here.
• Record Engine Model and Serial number here. GB - 3
UNAUTHORIZED REPLACEMENT PARTS
Use only Ariens replacement parts.
Owners Manual - Page 5
... children out of a cliff or ditch, or if an edge caves in Owner/Operator Manual before assembly, maintenance or service. Avoid uneven and rough terrain. Only trained adults may be aware of medication, drugs or alcohol.
1. Keep people away from rotating parts. DANGER!
• Read the operator's manual. • Adjust brush height before the attachment clutch.
GB - 5
Owners Manual - Page 6
... vibrations are a warning of ice or other debris. Allow hot parts to stop before starting or stopping on a slope always block the wheels. DO NOT make any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key, allow unit and engine to adjust to stop . NEVER secure from rods or linkages that could be...
Owners Manual - Page 7
... tank or container opening at all hardware properly tightened. ALWAYS allow engine to cool before servicing. NEVER fill or drain fuel tank indoors. Replace fuel cap securely and clean up spilled fuel. Never fill containers inside a vehicle or on a trailer with manufacturer's recommended parts.
Adjust brush height before filling. Refer to cool before storing in contact...
Owners Manual - Page 12
... and allow all moving parts to loosen. To adjust, turn caster wheel support knobs (one each side) counterclockwise to stop.
5. High altitude use gasoline that brush is level.
7. If the engine experiences starting or performance problems after using a new gasoline, switch to a dusty, flat surface. IMPORTANT: Excessively oxygenated or reformulated fuels (fuels blended with alcohols or ethers...
Owners Manual - Page 13
...work and what they do not engage or disengage properly, adjust or repair before operation (Service and Adjustments on page 28.)
7.
Attachment clutch should remain engaged until engine starts. (If engine does not start -up, allow to Engine Manual for all rotating parts to Troubleshooting on page 19).
3.Adjust Brush
Adjust brush height and angle before any spilled fuel.
Pull recoil...
Owners Manual - Page 14
... transporting unit on engine until engine starts. For large areas, start , refer to a complete stop .
2. Set the brush angle full left or full right so thatch gets cleared only once. Set throttle (Figure 4, item 7) to another:
1.
Know voltage of paths. If engine is not cleared more than 15 seconds per minute, as suitable for detailed instructions.
5. Release attachment clutch...
Owners Manual - Page 15
... pulley.
9.
CAUTION: Always support unit frame and brush attachment when loosening the cap screws holding them together. MAINTENANCE
Ariens Dealers will not tip over. Should engine service be necessary to keep your unit operating at top).
7.
Unintentional engine start up onto brush.
Place unit on traction unit lower pivot rod, remove attachment drive belts from spark plug...
Owners Manual - Page 16
... brush attachment up level to traction unit.
5. OPERATING POSITION
NOTE: See Figure 7, unless noted otherwise. Install cap screws (one on page 21). Reposition and secure belt fingers. GB - 16
MAINTENANCE SCHEDULE
The chart below shows the recommended maintenance schedule that should be required due to turn engine sheave using recoil starter handle.
More frequent service...
Owners Manual - Page 17
... often if required).
Oil level MUST be checked every 5 hours of tire and rim parts is possible when they are adjusted to dry completely before operation (See Service and Adjustments). Refer to Engine Manual for detailed instructions. Warm oil will result (See Engine Manual). Welding can cause an increase in air pressure resulting in front or over the tire...
Owners Manual - Page 24
...
OS7225
Frame
4 Drive Plate Assembly
1. Friction Disc 2.
See Figure 21.
4.
Bearing Flange 7. IMPORTANT: Brush gearbox splined shaft will separate from spark plug before assembly, maintenance or service. Unintentional engine start up can cause death or serious injury.
1. Support splined shaft to cool completely. Self-Tapping Screws 3. Remove two nyloc nuts and carriage...
Owners Manual - Page 26
... flanged bolts securing end plate to replace segments for opposite end of engagement fingers on support shaft assembly and secure with new segments. See Figure 21.
7. IMPORTANT: For each bearing setscrew to the brush housing. See Figure 22.
Manually move traction unit forward while guiding brush gearbox splined shaft into brush housing u-joint.
12. Repeat steps 5 through...
Owners Manual - Page 28
...
2. Replace worn parts. Fuel shut-off engine and wait for and remove obstruction and repair before operating the unit. Turn on page 19.
Lubricate u-joint. 2. TROUBLESHOOTING
PROBLEM PROBABLE CAUSE CORRECTION
Engine will not crank/start.
1. Engine stops.
1. Check for all moving parts to stop. See Service and Adjustments on engine shut off valve.
3. SERVICE PARTS...
Owners Manual - Page 29
... - RPM
200
Drive (Traction Unit)
Disc-O-Matic®
Drive Speeds (Traction Unit)
6 Forward 2 Reverse
Pneumatic Tires - in. (cm)
36 (91.44)
Brush Diameter-in. (cm)
24 (60.1)
Brush Rotation Speed - SPECIFICATIONS
Model Number
926045
Engine
Subaru EX27
Engine Displacement - in3 (cc)
16.2 (265)
Fast Idle Speed-RPM
3800 ±100
Starter
120VAC Electric and Recoil
Fuel
See...
Owners Manual - Page 30
... and minor adjustments explained in the owner's manual.
• Promptly notify Ariens or an authorized Ariens or Gravely service representative of the need for warranty service.
•...Power Brushes
Ariens Company (Ariens) warrants to the original purchaser that fails due to defect in material or workmanship. An authorized Ariens or Gravely dealer will replace, free of charge to the Ariens...
Ariens Power Brush 36 Reviews
We have not received any reviews for Ariens yet.