BenQ 7765PA - PalmPro XGA DLP Projector Support and Manuals
Get Help and Manuals for this BenQ item
Popular BenQ 7765PA Manual Pages
Operating Guide - Page 1
Digital Multimedia Projector
PalmPro 7763PA/65PA
OPERATING GUIDE
Thank you very much for purchasing this manual, keep it for portability (4) RGB input terminal (5) RS232 Communication (6) Mouse emulation (7) Complies with VESA DDC1/2B specifications
English I After reading this Acer DLP™ Technology Projector. Features
(1) High brightness (2) High resolution (3) Compact size, light ...
Operating Guide - Page 2
.... All rights reserved.
AND PLEASE READ ALL OF THESE INSTRUCTIONS BEFORE YOU OPERATE YOUR PROJECTOR. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to the contents hereof and specifically disclaims any warranties, merchantability or fitness for replacement. Do not attempt to notify any language or computer language...
Operating Guide - Page 4
...27
A
Lamp Replacement 27
B
Cleaning the Lens 27
C Troubleshooting 27
Specifications 29
A
Optical 29
B
Electrical 29
C Mechanical 29
D Preset Display Resolution Table 29
Appendix 30
AV Connection Port 30
AV Control Pad 30
A
Connecting the Box 31
English IV
Positioning 4
B. Adjustable Feet 4
Moving the Projector 5
Accessories 6
Connection 7
A
Connecting...
Operating Guide - Page 5
...vision; English 1
C Portability
This projector has a sophisticated shape, like that of an attaché case, with a geometric effect that is already set to the height of the line...65PA), and supports SXGA using TI's Digital Micromirror Device (DMD) and our own optical design, with a retractable carrying handle that increases light usage efficiency.
1 Introduction
Projector Features
A ...
Operating Guide - Page 9
... dust and scratches on the surface of the cabinet. Replace the lens cover and rotate the feet fully clockwise (to shorten the feet) when moving the projector. Do not transport the projector in an unsuitable transport case by using a courier or transport service. Caution The carry bag (supplied) is not designed to protect the...
Operating Guide - Page 10
Projection Lens
Manual
User's manual AAA Batteries
Figure 7 Accessories
Remote Control
Mac Adapter 15pin D-sub connector ADB Mouse adapter PS/2 Mouse adapter Serial Mouse adapter General cable
English 6 Please save ...
Operating Guide - Page 13
... if the horizontal frequency of the input signal exceeds the range of the projector.
The LED will then blink orange and the lamp will shut down, but the fan will continue to run for about 1 minute to turn on the lamp. "INPUT SIGNAL DETECTED, ACTIVATING AUTO IMAGE" will blink green during warm up...
Operating Guide - Page 15
To select items. To navigate through sub pages or to increase the scale bar number. English 11
To enter sub pages. Figure 13 Menu control pad
MAIN UNIT Menu
4 ( KEYSTONE+ ) 3 ( KEYSTONE- ) Exit (AUTO)
FUNCTION
To call the OSD menu. To navigate through sub pages or to decrease the scale bar number. To exit from the current page or OSD menu, and save setting changes.
Operating Guide - Page 17
... follow instructions in placing batteries into place. When the on the projector and to emulate mouse function when the projector is ...Disk Pad acts as indicated inside the battery
compartment. • Replace the lid and snap into the remote control units.
•...On
To turn the projection lamp on button. When operating in the direction of the arrow. • Install two 'AAA' batteries as...
Operating Guide - Page 18
... and 30 degrees vertical relative to a line that is a right angle to the remote sensor. In such cases, continued use of Lamp
The light source lamp has a limited service life. Replace the lamp with a new one. The distance between the remote control and remote sensor must be shorter than four meters (13 feet). Caution •...
Operating Guide - Page 20
... not well attached If the LED blinks rapidly, it on again. Temperature is too high If the projector's internal temperature is not attached properly. 3. Caution: The lamp indicator will turn it indicates that the lamp is too hot to operate safely, the LED will blink slowly for 45 minutes, then turn off , it...
Operating Guide - Page 21
... parts inside of the projector may explode if improperly handled. English 17 Loose screws could result in color unevenness, etc.)
Replace the lamp with a new one and fix it using the same screw.
• Firmly tighten the lamp screw. Turn the main power switch off the projector and unplug the AC cord. B Replacing the Lamp
Replacing the lamp When replacing the lamp...
Operating Guide - Page 26
...If flicker occurs on this page: Auto Resize, H. Size manually to the screen. H.Posit ion
(move
the
(move the image up)
image
down)
Position adjustments are saved when the projector is power off to adjust the H. Positio n
(move
..., users may turn Auto Image off . Phase
H. Size
Setting effects When Auto Resize is from Video other instead of the image to fit the screen size.
Operating Guide - Page 27
... 0 (stop). The default setting of lamp will automatically detect the video system.
And you can select desired video systems. When selecting system, the projector will detect the selected system ...There are
supported: English, French, German, Italian, Spanish,
Simple Chinese and Chinese. (See Figure 26). To set the time. 0 means Auto Off function inactive.
*Default setting is Video ...
Operating Guide - Page 31
... Select the correct video system.
C Troubleshooting
PROBLEMS NO POWER
NO PICTURE
IMAGE ISN'T ...projector back on the screen. Remove the lens cap. Stand within the adjustment range of the lens. Adjust the brightness and contrast. Adjust the focus. Make sure there is no obstacle between the unit and screen is not in use. 4 Maintenance and
Troubleshooting
A Lamp Replacement...
BenQ 7765PA Reviews
We have not received any reviews for BenQ yet.