BenQ MP510 - SVGA DLP Projector Support and Manuals
Get Help and Manuals for this BenQ item
Popular BenQ MP510 Manual Pages
User's Manual - Page 4
... lamp is recommended that you follow the instructions mentioned in this could fail if power cuts or surges
of this manual ...light beam may fluctuate or cut
out, it is on the projector or remote control.
4 Important safety instructions NOT stable. 1. Important safety instructions
Your BenQ projector is important that you operate your eyes. However, to qualified service...
User's Manual - Page 7
...is securely installed.
17.
If you to have the projector
serviced. Do not step on the
projector.
Besides probable
inverted pictures for ceiling mount
physical damage...BenQ to the projector, doing
installation. Use only BenQ's Ceiling Mount Kit for ceiling mounting of the wrong gauge or length screws. It is capable of the ceiling mount bracket. Safety instructions for mounting...
User's Manual - Page 8
... time and may vary within the lamp manufacturers specifications. Carefully unpack and verify that you have all of purchase. Standard packing list
1. Soft carry case
8 Introduction Shipping contents
The projector is normal and expected behavior. Projector 2. User manual 4. Power cord
Optional accessories
1. Quick start guide
5. Ceiling mounting kit
3. This is shipped with the...
User's Manual - Page 9
Video input socket 17. Quick-release foot 19. Lamp cover 20. Ceiling mounting screw holes
10
Introduction 9 AC power cord inlet 12. RS232 control port
Under side... 11. S-Video input socket
20 18. External control panel (See "Projector" on page 17 for servicing) 14. USB socket (for details.
6 1.
2. 7 3. 8 4. 9 5.
6. 7. 8. 9. RGB (PC)/Component video (YPbPr/ YCbCr) signal ...
User's Manual - Page 10
... for
on page 45 for details.)
details. 6. Selects the desired menu items.
10 Introduction Exits and saves the menu settings.
3.
Sequentially selects the input signal D-
"Indicators" on page 34 for details.)
8.
Lamp indicator light (See "Indicators" on page 27 for details.)
under operation. Indicates the status of the projected picture. Selects the desired...
User's Manual - Page 11
...as
setting available for details.)
Used to make adjustments.
4. TIMER SETUP (See "Setting the
...4 3
9
presentation timer" on page 25 for details.)
5
Automatically determines the best
picture timings for
details.)
10
Enters presentation timer setting... On/Show (See "Setting the
presentation timer" on your own timer setting.
7.
Remote control
5....
User's Manual - Page 13
... the projector suspended upside-down from the ceiling in the
Advanced > Mirror menu after you turn the projector on the ceiling.
Rear Table
Select this installation location. Note that a special rear projection screen and the BenQ Projector Ceiling Mounting Kit are required for quick setup and portability.
2. Set in front of screen; 2.
User's Manual - Page 22
... of the input signal exceeds the projector's operating range, you will be used in this manual, and keep the manual in a safe place.
5. The set and activated, the projector cannot be inconvenienced if you ever forget it is finished when the message "Password setup completed" displays.
If the frequency/resolution of the following 3 steps. The...
User's Manual - Page 23
... help from the local BenQ service center to confirm.
Perform one of the following 3 steps.
Press AUTO to decode the number. Press Up to the
Setting > Change Password menu.
2. Press MENU on the projector or MENU on the remote control to open the on to the
Setting > Password menu after the password is incorrect, a "Password Error" message displays. Write...
User's Manual - Page 24
... right corner of time. To set
the Auto Off time, go to the
Advanced > Auto Off menu and press Left/ Right
to set a time from the lamp may cause damage to your desired...can press the button again to the projector, you can manually press SOURCE repeatedly until your eyes.
2. To cycle through the available input signals: 1. The strong light from 5 to 20 minutes in the
Advanced menu is...
User's Manual - Page 41
... projector and in Economic mode helps to replace the lamp, please install a new lamp or consult your dealer.
This message will remind you notice that you may explode. This is time to extend the lamp life by the built-in the center of lamp time. Warning message
When the Lamp indicator lights up after 3000 hours usage. The following...
User's Manual - Page 44
... qualified service personnel for 5 seconds to let the OSD disappear.
For more detailed information, please refer to reset
Temperature information
When the Temperature warning light is too high. 2. 12. Resetting the lamp counter
Do not reset if the lamp is warning you of the following possible problems: 1. Press AUTO on the projector or on , it is not replaced as...
User's Manual - Page 48
... 72
48 Specifications
8. General
Product name
Digital Projector
Model name
MP510
Optical
Resolution
800 x 600 SVGA
Display system
1-CHIP DMD
Lens F/Number
F=2.57 (fixed)
Lamp
160 W lamp
Electrical
Power supply... input
RCA jack x1 D-sub Component RCA jack x 3, through RGB input
Control (for servicing)
USB mouse connector RS-232 serial control
A/B series x 1 mini Din 9 pin x...
User's Manual - Page 50
... of purchase date will be required with BenQ's written instructions, especially the ambient humidity must be replacement of any person of such revision or changes. *DLP, Digital Micromirror Device and DMD are copyrights of BenQ Corporation. All rights reserved. Further, BenQ Corporation reserves the right to the contents hereof and specifically disclaims any warranties, merchantability or...
TD PRJ PRG - Page 1
...
Manual Zoom, 1.22:1 Vertical + 40o
200W, 3000/4000 Hrs.
200W, 3000/4000 Hrs.
200W, 3000/4000 Hrs.
132W, 2000/3000 Hrs.
300W, 2000/3000 Hrs.
300W, 3000/4000 Hrs.
640x350 to 1280x1024
640x350 to 1280x1024
640x350 to 1280x1024
640x480 to 1280x1024
640x350 to 1280x1024
640x350 to change without notice. Price and Product specifications...
BenQ MP510 Reviews
We have not received any reviews for BenQ yet.