BenQ MX723 Support and Manuals
Get Help and Manuals for this BenQ item
Popular BenQ MX723 Manual Pages
MX723 and MW724 Quick Start Guide - Page 12
... (without notice. BenQ QSG-MX723_MW724.book Page 12 Monday, November 10, 2014 3:08 PM
(EN)
Specifications
All specifications are subject to ...Supports firmware upgrade Type A 1.5A output
Input terminals
Computer input RGB input D-Sub 15-pin (female) x 2
Video signal input S-VIDEO Mini DIN 4-pin port x 1 VIDEO RCA jack x 1 SD/HDTV signal input Analog - Optical
Resolution (MX723) 1024 x 768 XGA...
MX723, MW724 User Manual - Page 12
... you also purchase a separate Kensington lock compatible security cable and attach it is securely and safely installed. BenQ recommends that you purchased your attention to prevent possible damage to person and property. You can purchase a BenQ projector ceiling mount or wall mount kit from the ceiling or wall due to both the Kensington lock...
MX723, MW724 User Manual - Page 17
... will dictate which installation location you turn the projector on the remote control to position the projector for this location with the projector placed near the floor in the SYSTEM SETUP: Basic > Projector Installation menu after you turn the projector on the ceiling. Purchase the BenQ Projector Ceiling Mounting Kit from the ceiling behind the screen. Set Rear Ceiling in...
MX723, MW724 User Manual - Page 34
... BenQ service center to the SYSTEM SETUP: Advanced > Security Settings.
2. Open the OSD menu and go to decode the number. IMPORTANT: The digits being input will display a coded number on the projector. To leave the OSD menu, press Menu/Exit. Write your selected password down the number and turn on the screen.
2. Write down here in this manual...
MX723, MW724 User Manual - Page 35
.... 6. Switching input signal
The projector can also manually cycle through the available input signals.
1. You can be connected to the Security Settings page. Data (graphic) "PC" presentations using mostly
Operation 35 5. You will not have successfully assigned a new password to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system...
MX723, MW724 User Manual - Page 68
... -screen instructions to change the lamp.
It is strongly recommended that vary depending on page 66), you replace the lamp at this stage.
The lamp is normal lamp behavior.
The lamp brightness diminishes with Economic selected ("Setting Lamp Mode" on different models.
68 Maintenance "XXXX" shown in some instances the lamp may continue to replace the lamp, please install...
MX723, MW724 User Manual - Page 69
....lamprecycle.org.
• If lamp replacement is performed while the projector is underneath the lamp socket to avoid any possible injury or damage to dispose of electrical shock, always turn the projector off and disconnect the projector from the ceiling, make sure that you use caution when removing lamp glass that you purchase a BenQ projector lamp for approximately 45 minutes...
MX723, MW724 User Manual - Page 75
...) USB
Mini B Supports firmware upgrade Type A 1.5A output
Input terminals
Computer input RGB input D-Sub 15-pin (female) x 2
Video signal input S-VIDEO Mini DIN 4-pin port x 1 VIDEO RCA jack x 1 SD/HDTV signal input Analog -
Specifications 75 Component RCA jack x 3 (through RGB input) Digital-HDMI x 1
Audio signal input Audio in the Standby Settings is on environmental...
MX723, MW724 User Manual - Page 81
...than 4920 feet, and avoiding to operate the projector in any form or by BenQ Corporation. Others are trademarks of any defective parts (labor included). No part of BenQ Corporation. Warranty and Copyright information 81 Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with BenQ's written instructions, especially the ambient humidity must be...
Network Projector Operation Guide - Page 4
Example of an e-mail alert 21
Quick buttons 21 Using the web control lock 22
Projecting computer screen contents 23
One projector displaying one computer screen 23 Supported Resolutions 23 Using the Projection Login Code 23
PJLink Commands 24
4
Network Projector Operation Guide - Page 5
...administrator. Connecting the projector with the wired and/or wireless network function. The Network Settings page is displayed.
• Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu ... NETWORK SETTING on your Ethernet or router.
2. Press to highlight Apply and press MODE/ENTER. 7. Press to highlight DHCP and press / to select On. 6.
Preparation
Your BenQ projector is...
Network Projector Operation Guide - Page 9
.... The model cannot play sound if the input source is , you want to project. • To pause projection, click Pause. You can auto search then connect to complete the connection automatically.
You can also type a desired projector name and click Search. • Auto search and connect: If there is only one BenQ projector in...
Network Projector Operation Guide - Page 18
... activated, the projector can decide a 4-digit code in Login (4 Digits). If Projection Login Code is set to ON and User Defined Projection Login Code is designed to Default: The settings of connected computers. See "Using the Projection Login Code" on page 22 for more information. • Password Change: You can change the Admin password. • Projection Login Code: If activated...
Network Projector Operation Guide - Page 20
... the pre-defined projector system errors (see "Problems that trigger e-mail alert function" on page 21 for an example. • Mail Notification: Enable e-mail alert function by setting it to check if the Alert Mail works.
20 Controlling the projector remotely through a web browser The e-mail alert function is detected.
*: The SMTP protocol supports default TCP...
Network Projector Operation Guide - Page 24
... name. items
24 PJLink Commands INF1? Mute control. Power control. The below supported commands may vary depending on Lamp hour
Return "11 12 21 22 31 51 52 53" Return "Digital Projector" Return "Education Series" Return "BenQ" Return model name as below , "BenQ Projector" Return "Version" Error Status Return all status
Parameter 0 = Power Off 1 = Power On 0 = Power Off...
BenQ MX723 Reviews
We have not received any reviews for BenQ yet.