BenQ T420 Support and Manuals
Popular BenQ T420 Manual Pages
RS232 Commands for PDP and IFP Products - Page 2
...the control units that can sent or receive the RS232 protocol command.
2 Description 2.1 Hardware specification
LCD communication port in the rear side (1) Connector type: DSUB 9 Pin Male (2) ...and PC or other control unit with PC
2.2 Communication Setting
- 1 Introduction This document describes the hardware interface spec and software protocols of crossover (null modem) cable
required for use...
RS232 Commands for PDP and IFP Products - Page 6
...691; 011:Danish
Option, not support if the platform doesn't have this feature.
ʳ 012:Swedish
Option, not support if the platform doesn't have this feature.
ʳ 013:Italian
Option, not support if the platform doesn't have ...ʳ
42 000: Disable ʳ 001: Enable
All the buttons at the remote controller have no function
ʳ
ʳ 002: Passthrough Master Note: To set Pass through...
RS232 Commands for PDP and IFP Products - Page 7
...care Option, not support if the platform doesn't have this feature. ʳ Option, not support if the platform doesn't have this feature. ʳ Option, not support if the platform...; s 8ʳ s ʳʳ ʳ
ʳʳ ʳ
8ʳ s
ʳ 003: Passthrough Slave
Note1: To set Pass through,
the command must use the
"With ID protocal", and the ID
should between "01"~"98".
RS232 Commands for PDP and IFP Products - Page 8
... return "Invalid Command Reply". For touch model only. ʳ ʳ ʳ
V1.0
8 / 20
Commercial Display RS-232 Protocol Ex: value=012 means Year 2012 If the setting is illegal (Ex: Februrary doesn't ...001: Portrait A4 001 ~ 010
Option, not support if the platform doesn't have the date Feb/31), return "Invalid Command Reply". If the setting is illegal (Ex: Day31 doesn't exist in April...
RS232 Commands for PDP and IFP Products - Page 10
...=0x61 means the Timer no.1 is select
Wednesday, bit4 for
and enable, and its
enable/disable setting.
Byte4=0x00~0x3B. Timer is
enable or not. Byte1[6]: The Timer is
enable or not. Byte1..., bit1 for Friday, bit6 is disable.
On Timer.
On Timer.
Byte1[3:0]=0x1~0x07.
supported if the model doesn't have this
value is used to decide which
Timer is selected, and its On ...
RS232 Commands for PDP and IFP Products - Page 14
...set Pass through, the command
must use the "With ID protocal", and the ID ʳ should between "01"~"98". Option, not support if the platform doesn't have this feature.
Option, not support...691;
69 ʳ
6A ʳ ʳ
6C ʳ 6D 6E 70
002: Passthrough Master Note: To set Pass through, the command must use the "With ID protocal", and the ID
should be: Byte1=0x30, Byte2=0x35...
RS232 Commands for PDP and IFP Products - Page 16
... doesn't have this feature. Option, not support if the platform doesn't have this feature. Option, not support if the platform doesn't have this feature. Option, not support if the platform doesn't have this feature. For touch model only. Option, not support if the platform doesn't have this feature. Option, not support if the platform doesn't have this...
RS232 Commands for PDP and IFP Products - Page 20
...: Byte1 - Network Setting
14 ʳ g
Input Value: Byte1 - Byte2 - Byte1=0x02, Byte2=0xFF, Byte3=0xFF,
(2) If Byte1=0x01(IP Address) at Input value. Byte3...Byte9 (1) Byte1=0x00: IP Setup Mode
Byte1=0x01:...0x01 (same as Byte1 at Input
value, the return value should be
Byte1=0x00
Byte2=0x00: Manual
Ex: Subnet Mask=255.255.255.0, the return
E1
0x01: DHCP
value:
Byte3~9 are reserved...
T420 Data Sheet - Page 1
... simple to install in any office setting using a VESA wall mount. Trainer or speaker can always enjoy optimal picture quality in office. Connect your computer directly by enriching their meeting efficiency, training effectiveness, collaborative discussion, and team building.
Integrated Speaker
To help professional elites gain the competitive edge by touching the screen. Specifications
LCD...
Large Display User Manual - Page 2
... the prior written permission of this document. No part of BenQ Corporation. Copyright
Copyright 2012 BenQ Corporation. BenQ Corporation reserves the right to revise this publication and... to make changes from time to time in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual...
Large Display User Manual - Page 3
... 8
Parts of the display and their functions 9
Front panel 9 Rear panel 10 Input/output terminals 11 Remote control 13 Using the remote control 14
Setting up the display 15
Mounting the display 15 Connecting audio/video signals 18 Connecting the touch module 25 Connecting power 26
Using the touch screen 27
Calibrating the touch screen 30 Important instructions for...
Large Display User Manual - Page 25
The touch module supports easy Plug-and-Play operations. Setting up the display
25
Connecting the touch module
Connect the USB cable on the computer. T420
TL550
T650
There is no need to install additional drivers on the display to a computer.
Large Display User Manual - Page 30
... bent.
• Keep the touch screen out of the screen. Clean the retro-reflective bars as illustrated below. 30
Using the touch screen
Calibrating the touch screen
Ensure that you have installed the USB cable on the enclosed CD to perform the operation. A dusty environment may adversely affect the performance of your touch screen. You can calibrate the touch screen to use it more...
Large Display User Manual - Page 55
Troubleshooting
55
Troubleshooting
Problem No picture
No sound The computer input image looks strange
The control panel buttons do not work
Solution
Check the following :
• Have you turned on the mute function on the display or the input source device?
Have you chosen an unsupported output resolution on the computer? Refer to Supported...manually adjust the image. Unlock the buttons and...
BenQ T420 Reviews
Do you have an experience with the BenQ T420 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!