Bosch 1364 - 15 Amp Hand Held Abrasive Cutoff Machine Support and Manuals
Popular Bosch 1364 Manual Pages
Operating Instructions - Page 2
...or dust. Replace damaged cords ...operating a power tool. Do not use the cord to follow all instructions listed...support the workpiece to "Recommended sizes of Extension Cords" in the Accessory section of inattention while operating power tools may result in moving parts...install a polarized outlet. Refer to a stable platform.
A moment of this manual...on the switch or plugging ...
Operating Instructions - Page 3
... cause loss of control. When servicing a tool, use damaged or incorrect wheel flanges or round nut. Abrasive Cut-Off Machine Safety Rules
Always use tool if switch does not turn it is designed.
Keep cutting tools sharp and clean. A guard protects operator from broken wheel fragments. Hold tool by qualified repair personnel. Face shield or...
Operating Instructions - Page 4
...operator. Abrasive wheels may tend to climb out or recoil out of your side. These blades... Off Machines are the result of control during this manual.
Abrasive...machine near flammable materials.
Fragments from the operator, depending on auxiliary handle. Position the cord clear of cut material when wheel is set in a series of shallow depth of the tool. See the instructions...
Operating Instructions - Page 5
....
If wheel is binding, it may cause binding and recoil. Supports must be tight and secure before making a "Pocket Cut" into...motion or recoil may cut setting increases loading on how often you to remove the machine from the workpiece as ...
machine with approved safety equipment, such as the machine is binding, or when interrupting a cut . WARNING
Some dust created by the operator...
Operating Instructions - Page 6
... to Canadian Standards by Underwriters Laboratories.
Selector settings I, II, III,
Speed, torque or position settings.
Higher number means greater speed
0
Infinitely variable selector with off
Speed is listed to NOM Mexican Standards.
-6- This symbol designates that this tool is listed by Underwriters Laboratories, and listed to warning messages
Ni-Cad RBRC seal
Designates...
Operating Instructions - Page 7
...
GUARD
GUARD SECURING
CAP SCREW SPINDLE
SPINDLE LOCK
AUXILIARY HANDLE
MOUNTING BOLTS
Model No.
BM 1609929C59 12/02 12/10/02 9:44 AM Page 7
Functional Description and Specifications
! Cutting Depth Arbor No load RPM
1364
12" 3-7/8" 7/8" 5,000
1365
14" 4-7/8" 7/8"& 1" 4,300
NOTE: For tool specifications refer to the nameplate on your tool.
-7- Maximum capacities Abrasive wheel...
Operating Instructions - Page 8
... Switch enables the operator to "OFF" position automatically.
Install abrasive wheel onto spindle.
3.
The switch is running. INSTALLING ABRASIVE WHEELS Always use wheel guard, foot plate and auxiliary
handle with recess in the wheel can be bolted to guide and balance the tool can occur if
overtightened.
! Install inner flange onto spindle, with this abrasive cut off machine...
Operating Instructions - Page 9
... Depending on the wheel.
6. Replace bad wheels immediately. With the tool...Cutoff Machine set up in place.
CUTTING CONCRETE will normally break apart during this time.
2. Avoid overloading tool. ABRASIVE WHEELS Use aluminum oxide wheels for operating...Models 1364 & 1365 are not considered solid support structures.
8. Both can be used overhead or in direction away from the operator...
Operating Instructions - Page 10
....
-10- Replace housing screws and securely tighten screws.
5. Remove the auxiliary handle mounting bolts, reposition handle using auxiliary hole in guard, and remove foot plate.
4. BM 1609929C59 12/02 12/10/02 9:44 AM Page 10
REVERSING FIRE DIRECTION However we strongly recommend having this task performed by an authorized Bosch Service center.
1.
Operating Instructions - Page 11
...be replaced at once to six months the brushes be
performed by a Bosch Factory Service
Center or Authorized Bosch Service Station...maintain peak efficiency of operation, or at Bosch Factory Service Center or Authorized Bosch Service Station. BEARINGS After ...switch levers must be kept clean and free of power or
overheating. CAUTION
Certain cleaning agents and solvents damage
plastic parts...
Parts Diagram - Page 2
...600 206 020
1 600 206 030
1 601 334 008
Designation MOTOR HOUSING \ BLACK
Price group
31
FIELD \ 100-120V
39
FAN
14
ON-OFF SWITCH
31
POWER SUPPLY CORD \ USA/CDN 2,15m 2 x 2,08mm SJ 14/2 27
...HOLDING BRACKET
11
Page 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
http://le11288.le.de.bosch.com/sid/printdirect.asp?ID_PRODUCT=0601364039&ID_VERSION=1
Page 2 of 7 2/27/2007
Parts Diagram - Page 3
...1 601 110 449
REFERENCE PLATE \ CAUTION
11
1
651 1
1 605 510 213
PROTECTIVE COVER \ 12"
2
661 1
1 608 190 014
GUIDE BLOCK \ Ø 300 MM
2
661/03 2
2 910 281 246
ROUND-HEAD BOLT \ M 8x30 DIN 603
11
2
661/04 2
.../50 1
3 607 950 013
OFFSET SCREWDRIVER \ 3/8", SW9
22
2
http://le11288.le.de.bosch.com/sid/printdirect.asp?ID_PRODUCT=0601364039&ID_VERSION=1
Page 3 of 7 2/27/2007
Parts Diagram - Page 4
...; 25,4 MM), SW 28,6, SW 9,6
2
763 1
1 600 793 007
SUCTION BEND \ Ø 35 MM
2
810 1
1 607 014 171
CARBON-BRUSH SET
26
1
821 1
1 607 000 920
GEAR HOUSING
38
1
822 1
1 607 000 947
PARTS SET
37
1
830 1
1 604 011 155
ARMATURE \ 110-115V
51
1
840 1
1 607 000 206
PUSH-BUTTON \ BLACK
14
1
846 1
1 607...
Bosch 1364 Reviews
Do you have an experience with the Bosch 1364 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Bosch yet.
Earn 750 points for your review!