Brother International T-8752A Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International T-8752A manuals!
Problems with Brother International T-8752A?
Ask a Question
Free Brother International T-8752A manuals!
Problems with Brother International T-8752A?
Ask a Question
Popular Brother International T-8752A Manual Pages
Instruction Manual - English - Page 2
... sewing machines, it correctly.
Thank you must make the ground connection".)
T-8421A, 8422A, 8452A, 8722A, 8752A
i Indications
DANGER CAUTION
The instructions which follow this term indicate situations where failure to follow the instructions may result in the instruction manual. The instructions which follow this term indicate situations where failure to follow the...
Instruction Manual - English - Page 10
... kg.
The machine may cause your hand to the upright position with your Brother dealer or a qualified electrician for any tools, etc. The installation should only be carried out by a qualified technician. About the machine set-up location
Do not set up this sewing machine near the table holes. 2.
Use both hands to tilt...
Instruction Manual - English - Page 31
... trimmed automatically.
2142M
25
T-8421A, 8422A, 8452A, 8722A, 8752A When the treadle is
depressed backward, end backtacking is carried out. (For models with thread trimmer, the
thread is trimmed automatically.)
If the treadle has not yet been depressed backward, the end backtack function can be set the number of backtack stitches for A, B, C and...
Instruction Manual - English - Page 32
... that the indicator illuminates, the set number of stitches (start or end backtack stitches or fixed stitches) are sewn automatically and the thread is then trimmed (models with thread trimmer only) simply ...and to cancel warning conditions. (Refer to p.25.)
2156M
T-8421A, 8422A, 8452A, 8722A, 8752A
26 USING THE OPERATION PANEL (BASIC OPERATIONS)
(6) Fixed stitch key
When this key is pressed ...
Instruction Manual - English - Page 33
... 8422A, 8452A, 8722A, 8752A NOTE:
If the treadle is returned to the neutral position, the sewing machine will continue
operating until the set number of the thread trimming...After it has finished, the thread is trimmed automatically (models with thread trimmer, if the indicator of start backtack stitches
Example:
2 Setting end backtack stitches
2157M
Example:
2158M
3
Start backtacking ...
Instruction Manual - English - Page 34
... the setting can be changed.)
T-8421A, 8422A, 8452A, 8722A, 8752A
28 USING THE OPERATION PANEL (BASIC OPERATIONS)
2912M
1
Example:
2161M
From 1 to 1999 stitches can then be set.
2
After the set by ... stitches in E (fixed stitches) have been sewn. When the AUTO key is trimmed (models with thread trimmer) and the sewing machine switches to fixed stitch sewing mode.
2160M
Press ...
Instruction Manual - English - Page 37
...8752A ENTER key (4) This key is used to change the maximum sewing speed.
* Refer to change to stitch number display mode. (This completes the needle up stop position setting.)
Becomes higher
* A setting...power switch.
2. If you press the key, the setting value will become higher.
4. Press the or key (3) to the Service Manual for two seconds or more. Becomes lower
6-3.
Adjusting the...
Instruction Manual - English - Page 43
For all models except foundation specifications and T-8452A-405
Do not pass the thread through the thread amount adjuster... the thread amount adjuster (1) is moved to prevent skipped stitches, thread tightening problems such as looping, or thread breakages
37
T-8421A, 8422A, 8452A, 8722A, 8752A For foundation specifications and T-8452A-405
Pass the thread through . 8.
Do not pass the ...
Instruction Manual - English - Page 44
...cause your hand to use is broken. 2. Replace the needle if it is bent or if the...sewing.
2932M
T-8421A, 8422A, 8452A, 8722A, 8752A
38
Daily cleaning procedures
The following cleaning procedures ... if the treadle is depressed by Brother. * If this type of this...service life. Open the slide plates at the left and right. 3. Turn the machine pulley to move the needle to page 22.) 3. Install...
Instruction Manual - English - Page 50
...thread tension, or replace the bobbin or bobbin case. Adjust the thread take -up amount too large? TROUBLESHOOTING
11.
Sewing
Items with medium-weight material specifications, poor thread tightening...small? CAUTION
Turn off the power switch and disconnect the power cord before calling for repairs or service. If using a sewing machine with a "*" in severe injury.
DANGER
Wait at ...
Instruction Manual - English - Page 52
... spring attached? (Models with an oiled grindstone or replace it turns in the opposite direction to gradually reduce the sewing speed. Is the upper thread tension too strong? Make the thread take-up amount too small?
Is the bobbin scratched? The bobbin winding amount should not be more that 80 %. TROUBLESHOOTING
Problem 5 Uneven seam...
Instruction Manual - English - Page 57
INSTRUCTION MANUAL
Printed in Japan
http://www.brother.com/
T-8421A, 8422A, 8452A , 8722A, 8752A SA2698-301
2005.04.B (1)
Instruction Manual - Spanish - Page 57
MANUAL DE INSTRUCCIONES
Printed in Japan
http://www.brother.com/
T-8421A, 8422A, 8452A , 8722A, 8752A SA2698-301
2005.04.B (1)
Parts Manual - English - Page 2
T- 8752A- 4
2 1
1
0:
/ Minimum lubrication type
3:
/ Medium-weight materials
2
5: / Heavy-weight materials BROTHER INDUSTRIES, LTD.
Parts Manual - English - Page 36
Q Threading mechanism
REF.NO CODE Q'TY
ຠฬ
NAME OF PARTS
RM
1
SA3417001 1
2
SA3415001 2
1
SA2607001 1
2
SA3416001 2
UPPER THREAD TENSION ASSY, -3 TENSION SPRING, L UPPER...TAKE-UP SPRING, L GUIDE ASSY, T/TAKE-UP SPRING SPACER THREAD TAKE-UP SPRING, R COLLAR STOPPER SUPPORT NUT, 1 M3 SET SCREW, (CP) M3.5 SPRING GUIDE SET SCREW ADJUSTING THUMB SET SCREW, (CP) M3.5...
Brother International T-8752A Reviews
We have not received any reviews for Brother International yet.