Owners Manual
Page 8
...The thinner and harder the wood, the finer the teeth of the lower wheel. Never start the bandsaw with the workpiece in drive belt are unavoidably near the saw blade. The tiltable table is used for cutting curves, but will prevent unnecessary problems. a. c. e. d. "L" wrench (not 15rovided) ... turn the bandsaw off and disconnect the bandsaw from the center of the saw blade tension. The miter gauge is tilted downward. Use a dry brush. CHANGING THE DRIVE BELT a. Slowly feed the workpiece towards the saw blade tension by turning the lock switch on it , as the motor ...
...The thinner and harder the wood, the finer the teeth of the lower wheel. Never start the bandsaw with the workpiece in drive belt are unavoidably near the saw blade. The tiltable table is used for cutting curves, but will prevent unnecessary problems. a. c. e. d. "L" wrench (not 15rovided) ... turn the bandsaw off and disconnect the bandsaw from the center of the saw blade tension. The miter gauge is tilted downward. Use a dry brush. CHANGING THE DRIVE BELT a. Slowly feed the workpiece towards the saw blade tension by turning the lock switch on it , as the motor ...
Owners Manual
Page 9
The blade tension knob has not been tightened. 2. The saw blade. 4. The drive belt has snapped. 1. The wheels are dull or damaged. 4, Blade guides not suitably adjusted. 1. Try a new saw blade has broken. 4. Clean the machine regularly. Clean the ventilating slots of the wheels. 3. From ... the blade tension knob. 2. The blade teeth are not in a straight line. The saw blade or put on the bandsaw. Open the doors and check. 3. Replace the belt. 1. Use a 14 T.P.L saw blade does not cut in alignment or defective bearing. 2. Adjust the blade tracking knob (...
The blade tension knob has not been tightened. 2. The saw blade. 4. The drive belt has snapped. 1. The wheels are dull or damaged. 4, Blade guides not suitably adjusted. 1. Try a new saw blade has broken. 4. Clean the machine regularly. Clean the ventilating slots of the wheels. 3. From ... the blade tension knob. 2. The blade teeth are not in a straight line. The saw blade or put on the bandsaw. Open the doors and check. 3. Replace the belt. 1. Use a 14 T.P.L saw blade does not cut in alignment or defective bearing. 2. Adjust the blade tracking knob (...
Owners Manual
Page 11
...Lock Special Nut M22 Lower Door Leaf Spring Rivet 4X8 Lock Housing Special Spring Washer 10 Slotted Insert Hex. Socket Set Screw M6xlO Drive Belt Ball Bearing 12ram Retaining Ring 28 Lower Wheel Tire Retaining Ring 12 Saw Blade Upper Wheel Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M6 Cable w/...Indicator Tapping Screw ST3.5x9.5 Table Table Insert Hex. Bolt M6x45 Door locking knob body Hex. Nut M6 Slotted Insert Special Spring Washer 10 Lock Housing Upper Door Rivet 4x8 Leaf Spring Special Nut M22 Tongue Lock Spring Washer 6 Lock Nut M6 Blade Tension Knob Cap Blade...
...Lock Special Nut M22 Lower Door Leaf Spring Rivet 4X8 Lock Housing Special Spring Washer 10 Slotted Insert Hex. Socket Set Screw M6xlO Drive Belt Ball Bearing 12ram Retaining Ring 28 Lower Wheel Tire Retaining Ring 12 Saw Blade Upper Wheel Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M6 Cable w/...Indicator Tapping Screw ST3.5x9.5 Table Table Insert Hex. Bolt M6x45 Door locking knob body Hex. Nut M6 Slotted Insert Special Spring Washer 10 Lock Housing Upper Door Rivet 4x8 Leaf Spring Special Nut M22 Tongue Lock Spring Washer 6 Lock Nut M6 Blade Tension Knob Cap Blade...