D-Link DKVM-2U Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DKVM-2U manuals!
Problems with D-Link DKVM-2U?
Ask a Question
Free D-Link DKVM-2U manuals!
Problems with D-Link DKVM-2U?
Ask a Question
Popular D-Link DKVM-2U Manual Pages
User Manual - Page 2
Contents
Introduction 1 Product Features 2 Package Contents 2 Hardware Installation 3
Front Panel Layout 3 Rear Panel Layout 3
Using the DKVM-2/4 9
"Select" button 9 Keyboard "Hot Key" commands 10 Optional cable 11
Troubleshooting 12
Keyboard 12 Mouse 13 Video 14
Specifications 16
II
User Manual - Page 3
... like keyboard and mouse emulation for error free boot-ups and support is compatible with mouse and keyboard with PS/2 adapters in two ways: through a single console. Introduction
Thank you for the Microsoft Intellimouse and Microsoft Intellimouse Explorer. This product will ensure easy and accurate control over 2 or 4 PCs through keyboard "Hot Key" commands or by...
User Manual - Page 4
....
DKVM-2/4 Power Adapter
2 Uses inexpensive and commonly available cables. Molded KVM cables are recommended. Model No. The status of the active PC. "Select" push-button or keyboard "Hot Key" control. Package Contents
In addition to control 2/4 computers from one console. Keyboard and mouse emulation allows error-free boot-up to 1920 x 1440. Audible feedback when switching between...
User Manual - Page 9
... is connected to port PC1 will hear a beep. In particular, keyboard and mouse cables should be shown on your monitor. Now power up , and you will be checked because they are easily switched and they use the "Select" button to the DKVM-2/4 unit and plug it into a power outlet. Now make sure to...
User Manual - Page 10
If you switch PC ports on the KVM at this manual. If you find errors, recheck all cables for proper connections before going to the troubleshooting section of KVM switch or run hot key) while the computers are under their boot-up process, each PC will cause communication errors or initialization failures between PC and keyboard or mouse.
8 Normally, during boot-up...
User Manual - Page 11
... is caused by synchronization that the mouse cannot be used for around 2 seconds when the DKVM-2/4 switches to select which computer is the active system. "SELECT" BUTTON
Pressing the Select button cycles through computers 1 ~ 2/4
9 Use either the "Select" button on the unit, or make use of the keyboard "Hot key" commands. You may notice that...
User Manual - Page 12
... "HOT KEY" COMMANDS
To send "Hot Key" commands to give a "Hot Key" command. You will be shown on the monitor in a row, starting with DKVM-2)
Switch to Previous PC
Switch to Next PC
Go to Auto Scan mode
In Auto-Scan mode, the DKVM-2/4 unit will be given a beep as confirmation.
The following commands are supported:
FIRST KEY
SCROLL LOCK
SECOND KEY
THIRD KEY...
User Manual - Page 13
... DKVM-2/4 will result if a mouse move or keyboard key press is given just as the unit switches to prevent errors.
DKVM-CB 6 feet (180cm) 3-in-one Cable kit is needed to the next computer. In this mode, there is no mouse or keyboard control, which is available for DKVM-2/4 KVM switch.Visit www.dlinkshop.com for details.
11 OPTIONAL CABLE
Model...
Quick Installation Guide - Page 1
...• USB Mouse • VGA or Higher Monitor
DKVM-2U
2-Port USB KVM Switch
Check Your Package Contents
These are the items included with your purchase:
• DKVM-2U USB KVM Switch
• Quick Installation Guide
• 2 Sets of KVM Cables
If any of the above items are the property of their respective holders. DKVM-2U.02152006 All rights reserved. Software and specifications subject...
Quick Installation Guide - Page 2
... DKVM-2U is assembled with the supplied KVM cables fastened to your second computer (Computer 2).
Connect to the PC1 and PC2 ports. Plug the cable from PC1 into your first computer (Computer 1), and plug the cable from your KVM switch into your second computer (Computer 2).
2 Connect to switch quickly and easily between both computers. VGA Port
Mouse...
Quick Installation Guide - Page 3
... sure that both computers are turned OFF before installing the DKVM-2U to the keyboard port located on the DKVM-2U. Attach your computer's USB keyboard connector to avoid mouse and keyboard errors when booting up your computers.
Attach your computer's USB mouse connector to the blue VGA port located on the DKVM-2U.
3 Attach your monitor's 15-pin VGA connector to...
Quick Installation Guide - Page 4
...: Repeat these steps to attach the cables connected from the PC1 port of the DKVM-2U to the USB port located on the back of your computer case. Installing the DKVM-2U
The following steps apply to both of the DKVM-2U to be used by attaching the cables connected from the PC2 port of your computer case...
Quick Installation Guide - Page 5
Installing the DKVM-2U
Once you've completed your DKVM-2U installation, your connections may appear similar to the diagram below.
5
Quick Installation Guide - Page 6
... to enter the Hot Key switching mode. A beep confirms that the Hot Key switching mode is activated. Hot Key Menu
Scroll Lock + Scroll Lock + 1 : Switches to PC1 Scroll Lock + Scroll Lock + 2 : Switches to PC2 Scroll Lock + Scroll Lock + I : Switches to switch between the two PCs every 10 seconds. Scroll Lock + Scroll Lock + B : Enable/Disable Beep. Switching with the DKVM-2U
You can use...
Quick Installation Guide - Page 7
... detected, or there is a mouse error, check the
following :
•
Verify that the mouse is properly connected to the computer and to another.
•
Try resetting the mouse by
pressing Scroll Lock + Scroll Lock + M.
•
Allow the mouse to have a few seconds to synchronize when switching from the DKVM-2U for information on enabling
USB support on your motherboard/computer...
D-Link DKVM-2U Reviews
We have not received any reviews for D-Link yet.