Planning Guides
Page 1
...proper applications and cutout information. 3. See the planning guide for the particular appliance for external blower NOTES: 1. A B Circuit Requirement** ERV3615 36" (91.4 cm) 33 3/8" 84.8 cm) Three prong electrical outlet connected to change without notice. See following pages for further information... these raised vents only with a single Dacor approved remote or in raised position 15" (38.1 cm) warning • Observe all governing codes and ordinances during planning and installation. Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent Revised...
...proper applications and cutout information. 3. See the planning guide for the particular appliance for external blower NOTES: 1. A B Circuit Requirement** ERV3615 36" (91.4 cm) 33 3/8" 84.8 cm) Three prong electrical outlet connected to change without notice. See following pages for further information... these raised vents only with a single Dacor approved remote or in raised position 15" (38.1 cm) warning • Observe all governing codes and ordinances during planning and installation. Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent Revised...
Planning Guides
Page 2
... length for wind resistance. Avoid "S" or "back to back" configurations of the elbows and transitions from the hood exhaust as possible. ERV3615 Approved Dacor Blowers* Remote blowers: REMP3 or REMP16 In-line blowers: ILHSF8 or ILHSF10 For example, for each 90° elbow is 15 feet... especially when elbows are required. ■■ If multiple elbows are used, try to the blower installation instructions. Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent Revised 01/21/11 Page 2/3 PLANNING GUIDE Duct Work Design Tips ■■ Wherever possible, reduce...
... length for wind resistance. Avoid "S" or "back to back" configurations of the elbows and transitions from the hood exhaust as possible. ERV3615 Approved Dacor Blowers* Remote blowers: REMP3 or REMP16 In-line blowers: ILHSF8 or ILHSF10 For example, for each 90° elbow is 15 feet... especially when elbows are required. ■■ If multiple elbows are used, try to the blower installation instructions. Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent Revised 01/21/11 Page 2/3 PLANNING GUIDE Duct Work Design Tips ■■ Wherever possible, reduce...
Planning Guides
Page 3
www.Dacor.com Phone: (800) 7938-0.6093 Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent All tolerances: ±1/16" (±1.6 mm) unless otherwise stated Exhaust outlet location options side view front view Revised 01/...
www.Dacor.com Phone: (800) 7938-0.6093 Document # PG08-004 ERV3615 36" Wide, High Extension Slim Raised Vent All tolerances: ±1/16" (±1.6 mm) unless otherwise stated Exhaust outlet location options side view front view Revised 01/...
Installation Instructions
Page 5
..." (6.5 cm) Top cap with vent down 9/16" (1.4 cm) Tolerances: ±1/16" (±1.6 mm) unless otherwise stated A - See installation instructions for cooking appliance. Top Cap Width 36" (91.4 cm) B -
..." (6.5 cm) Top cap with vent down 9/16" (1.4 cm) Tolerances: ±1/16" (±1.6 mm) unless otherwise stated A - See installation instructions for cooking appliance. Top Cap Width 36" (91.4 cm) B -
Installation Instructions
Page 9
... equivalent length of each elbow and transition (see table) must be used with a REMP16 and the above components is: 15 feet + 15 feet + 4 feet + 2 feet = 36 feet. • The maximum amount of straight duct that is smaller in cross-sectional area than the required duct sizes in " the duct work that...
... equivalent length of each elbow and transition (see table) must be used with a REMP16 and the above components is: 15 feet + 15 feet + 4 feet + 2 feet = 36 feet. • The maximum amount of straight duct that is smaller in cross-sectional area than the required duct sizes in " the duct work that...