Dewalt D28493N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28493N manuals!
Problems with Dewalt D28493N?
Ask a Question
Free Dewalt D28493N manuals!
Problems with Dewalt D28493N?
Ask a Question
Popular Dewalt D28493N Manual Pages
Instruction Manual - Page 5
... to lose control. Replace damaged cords immediately.
General Safety Instructions
WARNING!
Never use an outdoor extension cord marked "W-A" or "W." Water entering a power tool will increase the risk of the 3 plug blades; Read and understand all instructions listed below, may ignite the dust or fumes.
ELECTRICAL SAFETY Grounded tools must , at all codes and ordinances. If...
Instruction Manual - Page 6
....
Use the correct tool for one tool may result in the hands of parts, and any adjustments, changing accessories, or storing the tool.
Properly maintained tools, with the switch is designed.
2
Do not use only identical replacement parts. Follow instructions in moving parts, breakage of untrained users. Keep proper footing and balance at the rate for...
Instruction Manual - Page 8
... for instructions on button (B) provides increased comfort in which a tool will be positioned 30°, 60°, and 90° left or right of harmful chemicals. • The label on how often you do this manual.
A lock-on rotating the gear case.
4 D28474 D28493 D28494 D28497 D28499
7" Angle Grinder 9" Angle Grinder 7"/9" Angle Grinder 7"/9" Angle Sander 7"/9" Angle Grinder...
Instruction Manual - Page 9
... DEWALT authorized service centers or qualified service personnel. The side handle must be inside the bend of the tool.
SOFT MOUNT The grinder is provided to prevent the
spindle from rotating when installing or removing
wheels. i.e., a new 7" wheel may not be properly positioned in five locations based on personal preference and application. Replacement should be replaced with part...
Instruction Manual - Page 12
...
English
CAUTION: Accessories must be purchased through DEWALT dealers and DEWALT Factory Service centers.
• One top position: Top handle position is designed for edge grinding applications. D284939
9" Type 27 guard
Rotating the Rear Handle
D284948 D284937 D284936 D284934 D284933 D284932
9" Type 28 guard 7" Type 27 guard 6" Type 11 Flaring cup guard with flange 4" Type 11 Flaring cup...
Instruction Manual - Page 13
... to a complete stop before making any adjustments or removing or installing accessories. Lock-on button will remain depressed and tool will remain on ...setting the tool down.
OPERATION
Power Source
Plug the Large Angle Grinder into a dedicated electrical circuit.
NOTE: If the gear case and motor housing become separated by more than 1/8", the tool must be done by a DEWALT Service...
Instruction Manual - Page 14
... the gear case
H
cover. DEWALT models D28493, D28494, D28474, D28499 are included in the groove on may only be used for use a wrench to the guard or the
mounting hub may be used without a guard only when sanding with conventional sanding
GRINDING WHEEL
SURFACE
discs. Mounting instructions for these accessory
guards are provided with a guard...
Instruction Manual - Page 15
...Allow the tool to reach full speed before setting it down .
11 WARNING: Do not...remove the
K
wheel. Install the metal backing flange (J) on the backing flange pilot.
Reverse the ... local dealer or authorized service center. 1. Wheel breakage and...Type 27 guard to 10˚ angle between the tool and work surface.
5.
tering the wheel on spindle J (E) against the backing flange...
Instruction Manual - Page 16
...installing accessories.
Place the sanding disc (M) on the clamp nut into the center of a guard. (See Mounting and Using Depressed Center Grinding Wheels and Sanding Flap Discs). Remove the tool from DEWALT service centers and DEWALT... in a straight line to 15˚ angle between the tool
and work sur- Finer grits...setting it down to operate at extra cost from the work surface.
Instruction Manual - Page 17
... cup wheel guard is off and unplug tool before setting it . Flaring cup wheels require proper flanges and guards.
removing or installing accessories. Before reconnecting the
1. Use only wire brushes and...2. Maintain a 5˚ to 10˚ angle between the spindle and the
operator to the tool guard D284936 are available as shown.
A Type 27 guard is off and unplug tool before ...
Instruction Manual - Page 18
... the spindle lock button and tighten the wheel by hand, seating wheel against backing flange before setting it down until the guard lug engages and rotates freely in the work surface before making any
adjustments or removing or installing
accessories. To remove the wheel, reverse the above procedure.
F
P
O
3. Position the guard facing backward, as...
Instruction Manual - Page 19
... to operate at high speed.
3. Lubrication
DEWALT tools are ready for use solvents or other harsh chemicals for cleaning the non-metallic parts of time, the guard becomes loose, tight...Remove Soft Mount (F).
2. Install the clamp nut, ensuring that the wheel remains centered
on the backing flange pilot.
4. This will keep you begin a cut, maintain the angle of the cutting wheel to...
Instruction Manual - Page 20
... the sides of purchase may be hazardous. Re-install the brush doors before making any accessory for a free replacement.
We will repair, without charge, any other qualified service personnel. This warranty gives you specific legal rights and you local dealer or authorized service center. FREE WARNING LABEL REPLACEMENT: If your DEWALT heavy duty industrial tool, simply return it to...
Parts Diagram - Page 3
Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for D28493N Type 3
Description
Qty Required
BEARING CUP
1
WASHER
1
WASHER
2
SPRING WASHER
1
LOCK NUT
1
ID LABEL
1
STATOR
1
RETAINING RING
1
BALL BEARING
1
DUST SHIELD
1
BEARING
1
BEARING,NEEDLE
1
SLEEVE
1
PIN
1
...
Parts Diagram - Page 4
All Rights Reserved. Page 3
Parts list, pricing, and availability subject to change. Please visit www.dewaltservicenet.com for D28493N Type 3
Description
Qty Required
PLATE,RETAINER
1
GREASE
1
GREASE,1 LB.
1
GREASE, 7LBS
1
COPYRIGHT© 2005. Item Number
127 800 800 800
Part Number
613366-00 30301914-01 429954-01 429954-00
Parts List for current parts information.
Dewalt D28493N Reviews
We have not received any reviews for Dewalt yet.