Dewalt DCG413FR2 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DCG413FR2 manuals!
Problems with Dewalt DCG413FR2?
Ask a Question
Free Dewalt DCG413FR2 manuals!
Problems with Dewalt DCG413FR2?
Ask a Question
Popular Dewalt DCG413FR2 Manual Pages
Instruction Manual - Page 3
... , if not avoided, may result in minor or moderate injury. (Used without word) Indicates a safety related message.
English
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any DeWALT tool, call us toll...
Instruction Manual - Page 5
...serviced by a qualified repair person using only identical replacement parts. c ) When battery pack is not in electrocution or shock. This will ensure that can result in electric shock, fire and/or serious injury.
Read all instructions... After inspecting and installing an accessory, position...follow all safety warnings, instructions, illustrations and specifications provided with this power...
Instruction Manual - Page 6
... grind with a new or replacement wheel installed, hold the tool in a...Specific for peripheral grinding, side forces applied to these conditions. b ) The grinding surface of center depressed wheels must be used to twisting or binding of the wheel in moving parts and should always be hazardous. Proper wheel flanges support... the operating action of this manual is snagged or pinched by ...
Instruction Manual - Page 7
...Specific for the dust exposure. Wear protective clothing and
wash exposed areas with large
battery packs will not cause a tripping or falling hazard.
Supports must be sure to read the safety instructions... activities contains chemicals known to the State of the wheel.
When ordering replacement battery packs, be placed under their definitions are as those dust masks that...
Instruction Manual - Page 8
...instructions for any reason. The battery pack can contact exposed battery terminals. If medical attention is needed, the battery electrolyte is attached to fit into the charger. Never attempt to the service... the appropriate Watt hour rating must be considered 3 batteries at the end of this manual for compatibility of three batteries with a hammer, stepped on . If battery liquid gets ...
Instruction Manual - Page 9
....
Failure to follow the warnings and instructions may also contact your local retailer for...service center or to your local recycling center for recycling. It does not indicate tool functionality and is only an indication of a cord suitable for Cord Sets
Volts 120 V
Total Length of Cord in this manual... The charger and battery pack are specifically designed to be charged
To actuate ...
Instruction Manual - Page 10
... with these standards when operated with Part 15 of such marks by DeWALT is...8226; The connectivity range is up to an authorized service center when service or repair is CAN ICES-3(B)/NMB-3(B) compliant.
• This... to this time or left in a residential installation. take it on environment and location.
•...and found to comply with the instructions, may impair the operation of ...
Instruction Manual - Page 11
... status of lithiumion battery packs, charge the battery pack fully before cleaning. Charger Cleaning Instructions
WARNING: Shock hazard. Important Charging Notes
1. This is connected to maximum charge rate...the slots. Fig. A cold battery pack will charge at an authorized service center. b. If charging problems persist, take the charger and battery pack to use water or any cleaning...
Instruction Manual - Page 12
... be recharged before use this manual for a complete list of ...serviced and re-assembled by more than 1/8" (3.0 mm), the tool must be released then depressed to store a fully charged battery pack in water or any adjustments or removing/ installing attachments or accessories.
SAVE THESE INSTRUCTIONS...steel wool, aluminum foil, or any part of charge. ASSEMBLY AND ADJUSTMENTS
...
Instruction Manual - Page 13
...installing is not against the wheel. An accidental start -up can also be used with conventional sanding discs. F)
CAUTION: Prior to provide maximum operator protection. Slide the guard into one of these instructions...The tool may require purchasing the correct guard from your local dealer or authorized service center. Mounting Guard (Fig. Mounting Non-Hubbed Wheels (Fig. Refer to ...
Instruction Manual - Page 14
... installed with sanding discs that it will normally break apart during this manual.
12 To remove the wheel, grasp and turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments... into the tool handle, align the battery pack with a wrench. Follow the instructions given in the Accessories Chart.
• Make sure the disc or wheel rotates...
Instruction Manual - Page 15
...line to the tool will run up and during use the correct guard per the instructions in this manual. If sanding with flap discs, move the tool constantly in the work surface....unexpected tool shutdown.
Allow the grinder to particular function. Lift the tool from rotating when installing or removing wheels. The tool will result and attached accessory may spin off by releasing the...
Instruction Manual - Page 17
.... DeWALT is a problem with your local dealer or authorized service center. no questions asked. In addition to products sold in Latin America, see country specific warranty information contained in case there is not responsible for any injury caused by tampering and may have been made or attempted by normal use identical replacement parts. This warranty...
Instruction Manual - Page 18
... smallest proper guard possible that does not contact the accessory.
* NOTE: A Type 1/41 guard is available at extra cost from your local dealer or authorized service center.
16 English 5" (125 mm) Grinding Wheels
ACCESSORIES CHART 5" (125 mm) Sanding Flap Discs
Sanding Discs
Type 27 guard Backing flange
Type 27 Depressed center...
Instruction Manual - Page 60
...and the array of the tool. Actual charge time may vary. Read the instruction manual for one or more specific information.
Nominal voltage is 18, 54 or 108. (120V Max* is under... chargeur. DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286 (JUN17) Part No. Lea el manual de instrucciones para obtener información más precisa.
* Maximum initial battery voltage (...
Dewalt DCG413FR2 Reviews
We have not received any reviews for Dewalt yet.