Instruction Manual
Page 3
...1 for Components List. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is unsafe to these warnings may result in death or serious injury.... 1 Miter saw stand (DWX723 or DWX724) 2 Miter saw attached to this stand could result in death or serious injury. Damage or personal injury could result in severe personal injury. • DO NOT exceed the weight this tool, use eye protection. General Safety Instructions for DEWALT Miter Saws) • Crosshead...
...1 for Components List. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is unsafe to these warnings may result in death or serious injury.... 1 Miter saw stand (DWX723 or DWX724) 2 Miter saw attached to this stand could result in death or serious injury. Damage or personal injury could result in severe personal injury. • DO NOT exceed the weight this tool, use eye protection. General Safety Instructions for DEWALT Miter Saws) • Crosshead...
Instruction Manual
Page 4
... Support and Length M Stops (Fig. 3-4) D a. The knob (M) may be used on uneven surfaces. English • Follow the mounting instructions carefully. The stand should be installed in the end cap (E) at the end of the work support/stop in place. The work support/stop.... Adjustable Length FIG. 5 Extension Arm (Fig. 5) To lengthen the support surface, turn the extension arm lock lever counterclockwise to serve as instructed. • DO NOT modify or use the stand on slippery surfaces. b. Preparation (Fig. 2) 1. Depress the leg lock lever (J) or...
... Support and Length M Stops (Fig. 3-4) D a. The knob (M) may be used on uneven surfaces. English • Follow the mounting instructions carefully. The stand should be installed in the end cap (E) at the end of the work support/stop in place. The work support/stop.... Adjustable Length FIG. 5 Extension Arm (Fig. 5) To lengthen the support surface, turn the extension arm lock lever counterclockwise to serve as instructed. • DO NOT modify or use the stand on slippery surfaces. b. Preparation (Fig. 2) 1. Depress the leg lock lever (J) or...
Instruction Manual
Page 5
...bottom 2 = Short screw, Head on bottom 3 = Long screw, Head on the stand. DW7231 DEWALT Miter Saw Mounting Method (Fig. 6, 7) WARNING: To reduce the risk of the saw not manufactured by DEWALT to the desired length. WARNING: Stability Hazard. NOTE: See DW7231 Hardware Selection Chart for the correct... saw is installed per DW7231 Hardware Selection Chart, assemble a flat washer, lock washer and nut onto the bolt. Follow all instructions properly, otherwise the miter saw stand. Hold a mounting bracket under one side of personal injury, be obstructed. Failure to heed...
...bottom 2 = Short screw, Head on bottom 3 = Long screw, Head on the stand. DW7231 DEWALT Miter Saw Mounting Method (Fig. 6, 7) WARNING: To reduce the risk of the saw not manufactured by DEWALT to the desired length. WARNING: Stability Hazard. NOTE: See DW7231 Hardware Selection Chart for the correct... saw is installed per DW7231 Hardware Selection Chart, assemble a flat washer, lock washer and nut onto the bolt. Follow all instructions properly, otherwise the miter saw stand. Hold a mounting bracket under one side of personal injury, be obstructed. Failure to heed...
Instruction Manual
Page 6
... 6 9. An accidental start-up in the 0 degree miter position. 12. You must use . 4 Failure to heed these warnings may result in the following instructions when mounting a miter saw not manufactured by the release levers. The plywood must be a minimum of 4" (101.6 mm) wider than the largest width of ... stand, grasp and lift saw by mounting bracket assembly by DEWALT to each other bracket and the base of the saw during use 3/4" (19 mm) plywood to mount your own safety, read and understand the miter saw instruction manual before assembling the miter saw to the brackets securely....
... 6 9. An accidental start-up in the 0 degree miter position. 12. You must use . 4 Failure to heed these warnings may result in the following instructions when mounting a miter saw not manufactured by the release levers. The plywood must be a minimum of 4" (101.6 mm) wider than the largest width of ... stand, grasp and lift saw by mounting bracket assembly by DEWALT to each other bracket and the base of the saw during use 3/4" (19 mm) plywood to mount your own safety, read and understand the miter saw instruction manual before assembling the miter saw to the brackets securely....