Fender MX-Meterbridge Support and Manuals
Get Help and Manuals for this Fender item
View All Support Options Below
Free Fender MX-Meterbridge manuals!
Problems with Fender MX-Meterbridge?
Ask a Question
Free Fender MX-Meterbridge manuals!
Problems with Fender MX-Meterbridge?
Ask a Question
Popular Fender MX-Meterbridge Manual Pages
Owners Manual - Page 2
...
Part Number. Whether you need to your sound system.
With your MX-Meterbridge from Fender Pro Audio, your eyes can see the music as it 's what you think you know that matters, it happens. The MX-Meterbridge allows you to +3 VU
600O Likewise, the MX-Meterbridge offers you the flexibility of your audio mix, the MX-5200 Series Professional Meterbridge...
Owners Manual - Page 3
... cutting of delicate conductive traces and soldering of your mx-meterbridge requires some modification to existing circuitry on the top ...-2,0,7/MY MAPNW /7//7,4714 10h7h7 1W7
MY PLEASE READ BEFORE INSTALLING YOUR METERBRIDGE. Installations performed by a Fender authorized electronics service center.
METERBRIDGE INSTALLATION
VERY IMPORTANT!
Proper installation of an added wire.
Owners Manual - Page 4
Very gently and very carefully lift and remove the Master I /O board, very carefully cut the top trace from P99 Pin #14.
CP7
MX-52I6 maw 1g OUTPUTS/t
Pr
0,
2
(*
INO•t• Ift01.1t0
*5'
O(1,11_ ."114 ,
Ot
.re
(*,
3
r*,
Solder Sid* Component Side
IF ILJ
it
MASTER I/O PCB
4) On the ...
Owners Manual - Page 5
...
MASTER I/O PCB
7) Very gently and very carefully, reinsert the Master I/O PCB and secure it using the washer/nut pairs and screws previously removed in the Meterbridge assembly kit, connect P69 located on the underside of the Master PCB. T 4 ( on the inside of the Master Output Panel to Pin #14 P99 located...
Owners Manual - Page 6
..., use hole pairs B and D. Remove the washers and nuts from the Meter Bridge.
° MX-52I6 MIXING 2
4), [ 691i 2
IA/
0
O (#),
A t ibriA '
0
O
O
Ot,...meterbridge as indicated below.
If you have an MX-5216, use hole pairs B and C.
Remove the washers and nuts from CHANNEL 1 INSERT and LINE INPUT and AUXIUARY OUTPUT 4 and MON OUT 2 jacks. MIXERS MX-5216 W-5224
MX-5232
INSTRUCTIONS...
Owners Manual - Page 7
...7 6 5 4 3 2
I /O PCB
*NOTE: Carefully fold the ribbon cable when re -installing the trim strip. From the Meterbridge, connect the 8-pin terminal socket to P99 located on the underside of the console.
/1
2 3 ...176;OOOO4" OO OO
ooa o 0000
o° 0000 0000
MX-52I6 MIXING ccksou-siliow,-====immer'
CCIt ES2 ayVE.E1
'04... HANG OUTSIDE THE MIXER.
12) Replace the Master Module Panel and secure ...
Owners Manual - Page 8
... R 1) Leave the input signal set up (Mono steps 1,2 and 3...to adjust the meterbridge unless you ... from the table) on the meterbridge until it reads 0 VU.
...- Please note: your meterbridge for a reference standard ... 0.
METERBRIMMI
Your MX-Meterbridge is a calibration ...your MX-Meterbridge has been preset at the...METERBRIDGE...Leave the Mono set up and ... L & R set up and read the ...
Fender MX-Meterbridge Reviews
We have not received any reviews for Fender yet.