Fluke 1507 CAL Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 1507 CAL manuals!
Problems with Fluke 1507 CAL?
Ask a Question
Free Fluke 1507 CAL manuals!
Problems with Fluke 1507 CAL?
Ask a Question
Popular Fluke 1507 CAL Manual Pages
Product Manual - Page 1
1507/1503 Insulation Testers Users Manual
June 2005 Rev. 1, 2/19
2005-2019 Fluke Corporation. All rights reserved. All product names are trademarks of their respective companies.
Product Manual - Page 4
.../1503
Users Manual
Testing the Batteries ...18 Testing the Fuse ...19 Replacing the Batteries and Fuse 20 Specifications...21
AC/DC Voltage Measurement 23 Earth-bond Resistance Measurement 24 Insulation Specifications 24
Model 1507 ...25 Model 1503 ...26 IEC 61557 Specification 26 Insulation Resistance Maximum and Minimum Display Values 28 Earth-Bond Resistance Maximum Display Values 32...
Product Manual - Page 5
.... Although this manual describes the operation of both Models 1507 and 1503, all illustrations and examples assume use of danger from the primary supply level (overhead or underground utility service). The Tester measures or tests the following: • AC / DC Voltage • Earth-Bond Resistance • Insulation Resistance
1 Introduction
The Fluke model 1507 and model 1503 are designed...
Product Manual - Page 8
... and EMC standards.
Conforms to the distribution part of the building's low-voltage MAINS installation. Measurement Category II is applicable to test and measuring ... as unsorted municipal waste.
4 Consult user documentation.
T
Fuse Double Insulated
Battery
6 WARNING.
1507/1503 Users Manual
Table 1. Symbols
Symbol
W X
P
~
Description
Symbol
...
Product Manual - Page 11
... position.
Indicates when the
insulation resistance measurement is active. Causes the Tester to configure the Tester for insulation tests.
Test lock. When pressed before the button, the test remains active until you press the button.
Sets a pass/fail limit for a polarization index or dielectric absorption ratio test.
Buttons and...
Product Manual - Page 13
...;
Appears on the primary display.
>
Indicates an out of range value. Calibrate the Tester.
9 Appears when
insulation test voltage is selected. The Tester will not operate at all until the battery is active. Insulation Testers Understanding the Display
Table 5. Invalid calibration data. ZERO
VAC, VDC, Ω, kΩ, MΩ, GΩ
Ohms lead zero is replaced.
Product Manual - Page 15
... avoid electric shock, injury, or damage to make measurements. Table 7.
Starts the Calibration mode.
when removing the test leads, remove the live lead; Power-Up Options
...the Tester, disconnect circuit power and discharge all LCD segments.
switch position displays the software version number.
switch position displays the model number. Insulation Testers Making...
Product Manual - Page 16
1507/1503 Users Manual
Measuring Volts
1507 INSULATION TESTER
Figure 5. See Testing the Fuse later in memory, and subtracts it from readings. Note
Measurements can be saved.
4. Connect the probes to the circuit to be performed on the display. The Tester measures the probe resistance, stores the reading in this manual. To measure resistance:
1. Short the ends of...
Product Manual - Page 17
The resistance reading appears on the lower portion of >2 V warns if voltage greater than the maximum display range, the Tester displays the > symbol and the maximum resistance for the range.
.
Insulation Testers Making Measurements
1507 INSULATION TESTER
bbw04f.emf
Figure 6.
Measuring Earth-Bond Resistance
13 Push and hold the button to start the test. When resistance...
Product Manual - Page 19
... Index and Dielectric Absorption Ratios (Model 1507)
1507 INSULATION TESTER
bbw05f.emf
Figure 7. Measuring Insulation Resistance
Measuring Polarization Index and Dielectric Absorption Ratios (Model 1507)
Polarization Index (PI) is the ratio of test clips is the ratio of the 1-minute insulation resistance to the 1 minute insulation resistance. Insulation tests should only be performed on...
Product Manual - Page 21
...
2.
bbw10f.emf
Figure 8. Measuring Polarization Index and Dielectric Absorption Ratios
17 To use the Compare function:
1. 1507 INSULATION TESTER
or
Insulation Testers Using the Compare Function (Model 1507)
Using the Compare Function (Model 1507)
Use the Compare function to set a pass/fail compare level for 1 second to select the desired compare value. The green pass indicator will...
Product Manual - Page 22
1507/1503 Users Manual
1507 INSULATION TESTER
Cleaning
Periodically wipe the case with no probes inserted.
2.
Press the blue button to the position with a damp cloth and mild detergent. bbw11f.emf
Figure 9. Using the Compare Function
18 Testing the Batteries
The Tester continuously monitors battery voltage.
To test the batteries:
1. If the low battery icon (...
Product Manual - Page 23
... . Testing the Fuse
XW Warning
To avoid electrical shock or injury, remove the test leads and any input signals before replacing the fuse. If the display reading is the fuse is bad and should be replaced.
1507 INSULATION TESTER
Insulation Testers Testing the Fuse
315 mA
Fuse
OK
Figure 10. Testing the Fuse
bbw06f.emf
19...
Product Manual - Page 29
Model 1507
Output Voltage
50 V dc (0 % to + 20 %)
100 V dc (0 % to + 20 %)
250 V dc (0 % to +...01 MΩ 0.1 MΩ 0.01 MΩ 0.1 MΩ 0.01 MΩ 0.1 MΩ 0.01 MΩ 0.1 MΩ 1 MΩ 0.1 MΩ 1 MΩ 0.1 GΩ
Insulation Testers Specifications
Test Current 1 mA @ 50 kΩ
Accuracy ± (% of Rdg + Digits)
± (3 % + 5)
1 mA @ 100 kΩ
± (3 % + 5)
1 mA ...
Fluke 1507 CAL Reviews
Do you have an experience with the Fluke 1507 CAL that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!