Fluke A3003 FC Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke A3003 FC manuals!
Problems with Fluke A3003 FC?
Ask a Question
Free Fluke A3003 FC manuals!
Problems with Fluke A3003 FC?
Ask a Question
Popular Fluke A3003 FC Manual Pages
Quick Reference Guide - Page 1
...2
INRUSH
Hz
LOG
3 INRUSH
Hz
1
2
4
5
6
Tactile Barrier
Backlight
40 sec
LOG
INRUSH
1
2 Hz
5
6
LOG
INRUSH
3
4
Hz
7
8
PN 4583110 March 2015 © 2015 Fluke Corporation.
a3003 FC
Wireless DC Clamp
Quick Reference Guide
Warning To prevent possible electrical shock, fire, or personal injury, read the "a3003 FC Safety Sheet" before you use this Product.
Calibration Manual - Page 1
All product names are trademarks of their respective companies.
All rights reserved. a3003 FC/a3004 FC Wireless DC Clamp
Calibration Manual
December 2017 ©2017 Fluke Corporation.
Calibration Manual - Page 5
....com. For complete operating instructions, see www.fluke.com. Introduction
W Warning Read all the information necessary to 2000 A dc current (a3003 FC) or 100 mA dc current (a3004 FC) using a detachable clamp. To register your product, visit http://register.fluke.com. To view, print, or download the latest manual supplement, visit http://us.fluke.com/usen/support/manuals.
1
The Product...
Calibration Manual - Page 6
...instructions. Use the Product only as specified, or the protection supplied by the Product can cause damage to prevent incorrect
measurements. Have an approved technician repair the Product. Use only specified replacement parts... Product with local and national safety codes. a3003 FC/a3004 FC Calibration Manual
Safety Information
A Warning identifies hazardous ...
Calibration Manual - Page 7
....
Repair the Product before use ... part of the building's low-voltage MAINS installation.... RISK OF DANGER. HAZARDOUS VOLTAGE. Risk of any combination of test probe, test probe accessory, current clamp accessory, and the Product is the LOWEST rating of electric shock.
The affixed label indicates that can cause burns or explode. Do not dispose of this manual...
Calibration Manual - Page 8
2000A DC CURRiE2NT00CL0AMP
a3003 FC/a3004 FC Calibration Manual
Tactile Barrier Figure 1. a3003 FC Wireless DC Clamp
Tactile Barrier Figure 2. a3004 FC Wireless DC Clamp 4
Calibration Manual - Page 9
... Specifications
Specifications
Maximum Voltage between Terminals and Earth Ground 30 V Range
a3003 FC 1.0 A to 999.9 A dc, 1000 A to 2000 A dc (with Fluke i2000 Current Clamp) a3004 FC 0.05 mA to 20.99 mA dc, 21.0 mA to 99.9 mA dc (with Fluke i20 Current Clamp) Resolution a3003 FC 0.1 A, 1 A a3004 FC 0.01 mA, 0.1 A Accuracy a3003 FC 2 % ±5 digits, 2.5 % ±5 digits a3003 FC...
Calibration Manual - Page 10
... Communication Equipment. Coil
--
a3003 FC/a3004 FC Calibration Manual
Electromagnetic Compatibility (EMC) International...PN: 4628796)
Cable
CABLE ASSEMBLY,1000V, 914MILLIMETER, SILICON,BLACK,A3003FC (PN: 4632023)
For 2000 A Clamp Calibration
Transconductance Amplifier
..., diameter 4 m
Recommended Model Fluke 5522A Only for a3003 DC Meter Only for industrial electromagnetic...
Calibration Manual - Page 12
...parts in the work station.
• Put shorting strips on the edge of the connector to static sensitive parts. a3003 FC/a3004 FC Calibration Manual... practices to minimize damage to help protect installed staticsensitive parts.
• Use anti-static type solder...the original
• Handle static-sensitive parts
• Handle static-sensitive parts by non-conductive edges. containers until...
Calibration Manual - Page 14
... any part of the Meter. 3. Test the Display To verify that the Product operates within the published specifications. The display shows ----. 2. Do the performance tests periodically and after service or repair. See Figure 4. Figure 4. With the Meter off , push and hold . 2. Plug the clamp into the Meter:
• 2000 A dc clamp into the a3003 FC...
Calibration Manual - Page 16
... with 2 banana jacks at both ends. a. a3003 FC/a3004 FC Calibration Manual
Table 3. a3003 and a3004 DC Meter Performance Verification
Test Connection
Single...(950.0 A) 80 mA (2000 A) -550 mV -190 mV -100 mV -10 mV 0 mV 10 mV 100 mV 190 mV 550 mV
Resolution Specification
0.1
1.0 % ±5 digits
0.01
0.2 % ±5 digits
0.01
0.2 % ±5 digits
0.01
0.2 % ±5 digits
0.01
0.2...
Calibration Manual - Page 18
a3003 FC/a3004 FC Calibration Manual
5522A CALIBRATOR
STBY 7 4 1
+/
L3 PHASE N PHASE
HIGH CURRENT OUTPUT
180A PK 7V PK MAX
850V PK MAX
HI LO W CURRENT OUTPUT
HI
30A PK 7V PK MAX
LO
LO
850V PK MAX
PUT
HI
3V PK 300mA PK MAX
LO
10V PK MAX
Figure 6. Calibration Connections for 2000 A Clamp
14
Calibration Manual - Page 20
... the calibration adjustment the temperature must be factory-calibrated to room temperature. 2. b. a3003 FC/a3004 FC Calibration Manual
Figure 7. Calibration Steps for the Meter
Calibration Step
Calibrator Output (mV)
A3303
A3304...Follow the instructions to enter normal measurement.
16 Push until PoS shows on the display. For each value in Enter the Password until ...
Calibration Manual - Page 22
...set the 12 A dc output to drive the high current from 52120A.
18 Push to the Meter. a3003 FC/a3004 FC Calibration Manual...passes. Follow the instructions to the 3 kA...the 5522A, set the parameters: ...bottom area of the jaw. 5. Calibration Specifications 2000 A Clamp
Display
Output to 3KA...mA
C-06
-2000 A
-80 mA
[1]: Manually adjust the current signal from the 5522A to the...
Calibration Manual - Page 24
a3003 FC/a3004 FC Calibration Manual
Replaceable Parts User-replaceable parts and accessories are shown in Table 9. User-Replaceable Parts
Description
Fluke Part Number
Battery Door Batteries
4583058 376756
20 Table 9.
Fluke A3003 FC Reviews
We have not received any reviews for Fluke yet.